u-boot/arch/arm/dts/zynqmp-sck-kv-g-revB.dts
Michal Simek dd0ebfe8a4 arm64: zynqmp: Remove comment about gem spec in kv260
The latest SOM specification doesn't enforce certain MIO lines allocated
for ethernet or ethernet controller itself. That's why remove comment about
it which is likely there from early version of specification.
Also removed the same comment from pinctrl node. It is clear that it has to
be defined for different carrier cards.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9406377bf2c391ac0200670511bd6b0edb097c96.1676880543.git.michal.simek@amd.com
2023-03-09 13:15:00 +01:00

332 lines
6.4 KiB
Text

// SPDX-License-Identifier: GPL-2.0
/*
* dts file for KV260 revA Carrier Card
*
* (C) Copyright 2020 - 2021, Xilinx, Inc.
*
* Michal Simek <michal.simek@xilinx.com>
*/
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/net/ti-dp83867.h>
#include <dt-bindings/phy/phy.h>
#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
/dts-v1/;
/plugin/;
&{/} {
compatible = "xlnx,zynqmp-sk-kv260-rev1",
"xlnx,zynqmp-sk-kv260-revB",
"xlnx,zynqmp-sk-kv260", "xlnx,zynqmp";
model = "ZynqMP KV260 revB";
};
&i2c1 { /* I2C_SCK C23/C24 - MIO from SOM */
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1_default>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
scl-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
sda-gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
u14: ina260@40 { /* u14 */
compatible = "ti,ina260";
#io-channel-cells = <1>;
label = "ina260-u14";
reg = <0x40>;
};
/* u43 - 0x2d - USB hub */
/* u27 - 0xe0 - STDP4320 DP/HDMI splitter */
};
&amba {
ina260-u14 {
compatible = "iio-hwmon";
io-channels = <&u14 0>, <&u14 1>, <&u14 2>;
};
si5332_0: si5332_0 { /* u17 */
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <125000000>;
};
si5332_1: si5332_1 { /* u17 */
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <25000000>;
};
si5332_2: si5332_2 { /* u17 */
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <48000000>;
};
si5332_3: si5332_3 { /* u17 */
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <24000000>;
};
si5332_4: si5332_4 { /* u17 */
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <26000000>;
};
si5332_5: si5332_5 { /* u17 */
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <27000000>;
};
};
/* DP/USB 3.0 */
&psgtr {
status = "okay";
/* pcie, usb3, sata */
clocks = <&si5332_5>, <&si5332_4>, <&si5332_0>;
clock-names = "ref0", "ref1", "ref2";
};
&zynqmp_dpsub {
status = "okay";
phy-names = "dp-phy0", "dp-phy1";
phys = <&psgtr 1 PHY_TYPE_DP 0 0>, <&psgtr 0 PHY_TYPE_DP 1 0>;
assigned-clock-rates = <27000000>, <25000000>, <300000000>;
};
&zynqmp_dpdma {
status = "okay";
assigned-clock-rates = <600000000>;
};
&usb0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0_default>;
phy-names = "usb3-phy";
phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
assigned-clock-rates = <250000000>, <20000000>;
usb5744: usb-hub { /* u43 */
status = "okay";
compatible = "microchip,usb5744";
i2c-bus = <&i2c1>;
reset-gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
};
};
&dwc3_0 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
maximum-speed = "super-speed";
};
&sdhci1 { /* on CC with tuned parameters */
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdhci1_default>;
/*
* SD 3.0 requires level shifter and this property
* should be removed if the board has level shifter and
* need to work in UHS mode
*/
no-1-8-v;
disable-wp;
xlnx,mio-bank = <1>;
clk-phase-sd-hs = <126>, <60>;
clk-phase-uhs-sdr25 = <120>, <60>;
clk-phase-uhs-ddr50 = <126>, <48>;
assigned-clock-rates = <187498123>;
bus-width = <8>;
};
&gem3 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gem3_default>;
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
mdio: mdio {
#address-cells = <1>;
#size-cells = <0>;
phy0: ethernet-phy@1 {
#phy-cells = <1>;
reg = <1>;
compatible = "ethernet-phy-id2000.a231";
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
ti,dp83867-rxctrl-strap-quirk;
reset-assert-us = <100>;
reset-deassert-us = <280>;
reset-gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
};
};
};
&pinctrl0 {
status = "okay";
pinctrl_uart1_default: uart1-default {
conf {
groups = "uart1_9_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
drive-strength = <12>;
};
conf-rx {
pins = "MIO37";
bias-high-impedance;
};
conf-tx {
pins = "MIO36";
bias-disable;
};
mux {
groups = "uart1_9_grp";
function = "uart1";
};
};
pinctrl_i2c1_default: i2c1-default {
conf {
groups = "i2c1_6_grp";
bias-pull-up;
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
mux {
groups = "i2c1_6_grp";
function = "i2c1";
};
};
pinctrl_i2c1_gpio: i2c1-gpio {
conf {
groups = "gpio0_24_grp", "gpio0_25_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
mux {
groups = "gpio0_24_grp", "gpio0_25_grp";
function = "gpio0";
};
};
pinctrl_gem3_default: gem3-default {
conf {
groups = "ethernet3_0_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
conf-rx {
pins = "MIO70", "MIO72", "MIO74";
bias-high-impedance;
low-power-disable;
};
conf-bootstrap {
pins = "MIO71", "MIO73", "MIO75";
bias-disable;
low-power-disable;
};
conf-tx {
pins = "MIO64", "MIO65", "MIO66",
"MIO67", "MIO68", "MIO69";
bias-disable;
low-power-enable;
};
conf-mdio {
groups = "mdio3_0_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
bias-disable;
};
mux-mdio {
function = "mdio3";
groups = "mdio3_0_grp";
};
mux {
function = "ethernet3";
groups = "ethernet3_0_grp";
};
};
pinctrl_usb0_default: usb0-default {
conf {
groups = "usb0_0_grp";
power-source = <IO_STANDARD_LVCMOS18>;
};
conf-rx {
pins = "MIO52", "MIO53", "MIO55";
bias-high-impedance;
drive-strength = <12>;
slew-rate = <SLEW_RATE_FAST>;
};
conf-tx {
pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
"MIO60", "MIO61", "MIO62", "MIO63";
bias-disable;
drive-strength = <4>;
slew-rate = <SLEW_RATE_SLOW>;
};
mux {
groups = "usb0_0_grp";
function = "usb0";
};
};
pinctrl_sdhci1_default: sdhci1-default {
conf {
groups = "sdio1_0_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
bias-disable;
};
conf-cd {
groups = "sdio1_cd_0_grp";
bias-high-impedance;
bias-pull-up;
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
mux-cd {
groups = "sdio1_cd_0_grp";
function = "sdio1_cd";
};
mux {
groups = "sdio1_0_grp";
function = "sdio1";
};
};
};
&uart1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1_default>;
};