mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-03 18:10:13 +00:00
c63e137014
JEDEC spec requires the clocks to be stable before deasserting reset signal for RDIMMs. Clocks start when any chip select is enabled and clock control register is set. This patch also adds the interface to toggle memory reset signal if needed by the boards. Signed-off-by: York Sun <yorksun@freescale.com>
95 lines
2.8 KiB
C
95 lines
2.8 KiB
C
/*
|
|
* Copyright 2008-2011 Freescale Semiconductor, Inc.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* Version 2 as published by the Free Software Foundation.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/io.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/fsl_ddr_sdram.h>
|
|
|
|
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
|
|
#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
|
|
#endif
|
|
|
|
void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
|
|
unsigned int ctrl_num, int step)
|
|
{
|
|
unsigned int i;
|
|
ccsr_ddr_t *ddr = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
|
|
|
|
#if defined(CONFIG_SYS_FSL_ERRATUM_NMG_DDR120) && defined(CONFIG_MPC85xx)
|
|
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
|
|
uint svr;
|
|
#endif
|
|
|
|
if (ctrl_num) {
|
|
printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
|
|
return;
|
|
}
|
|
|
|
#ifdef CONFIG_SYS_FSL_ERRATUM_NMG_DDR120
|
|
/*
|
|
* Set the DDR IO receiver to an acceptable bias point.
|
|
* Fixed in Rev 2.1.
|
|
*/
|
|
svr = get_svr();
|
|
if ((SVR_MAJ(svr) == 1) || IS_SVR_REV(svr, 2, 0)) {
|
|
if ((regs->ddr_sdram_cfg & SDRAM_CFG_SDRAM_TYPE_MASK) ==
|
|
SDRAM_CFG_SDRAM_TYPE_DDR2)
|
|
out_be32(&gur->ddrioovcr, 0x90000000);
|
|
else
|
|
out_be32(&gur->ddrioovcr, 0xA8000000);
|
|
}
|
|
#endif
|
|
|
|
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
|
|
if (i == 0) {
|
|
out_be32(&ddr->cs0_bnds, regs->cs[i].bnds);
|
|
out_be32(&ddr->cs0_config, regs->cs[i].config);
|
|
|
|
} else if (i == 1) {
|
|
out_be32(&ddr->cs1_bnds, regs->cs[i].bnds);
|
|
out_be32(&ddr->cs1_config, regs->cs[i].config);
|
|
|
|
} else if (i == 2) {
|
|
out_be32(&ddr->cs2_bnds, regs->cs[i].bnds);
|
|
out_be32(&ddr->cs2_config, regs->cs[i].config);
|
|
|
|
} else if (i == 3) {
|
|
out_be32(&ddr->cs3_bnds, regs->cs[i].bnds);
|
|
out_be32(&ddr->cs3_config, regs->cs[i].config);
|
|
}
|
|
}
|
|
|
|
out_be32(&ddr->timing_cfg_3, regs->timing_cfg_3);
|
|
out_be32(&ddr->timing_cfg_0, regs->timing_cfg_0);
|
|
out_be32(&ddr->timing_cfg_1, regs->timing_cfg_1);
|
|
out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2);
|
|
out_be32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2);
|
|
out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode);
|
|
out_be32(&ddr->sdram_mode_2, regs->ddr_sdram_mode_2);
|
|
out_be32(&ddr->sdram_md_cntl, regs->ddr_sdram_md_cntl);
|
|
out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval);
|
|
out_be32(&ddr->sdram_data_init, regs->ddr_data_init);
|
|
out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl);
|
|
out_be32(&ddr->init_addr, regs->ddr_init_addr);
|
|
out_be32(&ddr->init_ext_addr, regs->ddr_init_ext_addr);
|
|
|
|
/*
|
|
* 200 painful micro-seconds must elapse between
|
|
* the DDR clock setup and the DDR config enable.
|
|
*/
|
|
udelay(200);
|
|
asm volatile("sync;isync");
|
|
|
|
out_be32(&ddr->sdram_cfg, regs->ddr_sdram_cfg);
|
|
|
|
/* Poll DDR_SDRAM_CFG_2[D_INIT] bit until auto-data init is done. */
|
|
while (in_be32(&ddr->sdram_cfg_2) & 0x10) {
|
|
udelay(10000); /* throttle polling rate */
|
|
}
|
|
}
|