mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-30 00:21:06 +00:00
cd93d625fd
Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
152 lines
3.2 KiB
C
152 lines
3.2 KiB
C
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
|
/*
|
|
* Copyright (c) 2018 Microsemi Corporation
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <image.h>
|
|
#include <init.h>
|
|
#include <asm/io.h>
|
|
#include <led.h>
|
|
#include <miiphy.h>
|
|
#include <linux/bitops.h>
|
|
#include <linux/delay.h>
|
|
|
|
enum {
|
|
BOARD_TYPE_PCB110 = 0xAABBCE00,
|
|
BOARD_TYPE_PCB111,
|
|
BOARD_TYPE_PCB112,
|
|
};
|
|
|
|
int board_early_init_r(void)
|
|
{
|
|
/* Prepare SPI controller to be used in master mode */
|
|
writel(0, BASE_CFG + ICPU_SW_MODE);
|
|
clrsetbits_le32(BASE_CFG + ICPU_GENERAL_CTRL,
|
|
ICPU_GENERAL_CTRL_IF_SI_OWNER_M,
|
|
ICPU_GENERAL_CTRL_IF_SI_OWNER(2));
|
|
|
|
/* Address of boot parameters */
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE;
|
|
|
|
/* LED setup */
|
|
if (IS_ENABLED(CONFIG_LED))
|
|
led_default_state();
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void vcoreiii_gpio_set_alternate(int gpio, int mode)
|
|
{
|
|
u32 mask;
|
|
u32 val0, val1;
|
|
void __iomem *reg0, *reg1;
|
|
|
|
if (gpio < 32) {
|
|
mask = BIT(gpio);
|
|
reg0 = BASE_DEVCPU_GCB + GPIO_GPIO_ALT(0);
|
|
reg1 = BASE_DEVCPU_GCB + GPIO_GPIO_ALT(1);
|
|
} else {
|
|
gpio -= 32;
|
|
mask = BIT(gpio);
|
|
reg0 = BASE_DEVCPU_GCB + GPIO_GPIO_ALT1(0);
|
|
reg1 = BASE_DEVCPU_GCB + GPIO_GPIO_ALT1(1);
|
|
}
|
|
val0 = readl(reg0);
|
|
val1 = readl(reg1);
|
|
if (mode == 1) {
|
|
writel(val0 | mask, reg0);
|
|
writel(val1 & ~mask, reg1);
|
|
} else if (mode == 2) {
|
|
writel(val0 & ~mask, reg0);
|
|
writel(val1 | mask, reg1);
|
|
} else if (mode == 3) {
|
|
writel(val0 | mask, reg0);
|
|
writel(val1 | mask, reg1);
|
|
} else {
|
|
writel(val0 & ~mask, reg0);
|
|
writel(val1 & ~mask, reg1);
|
|
}
|
|
}
|
|
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
if (gd->board_type == BOARD_TYPE_PCB110 ||
|
|
gd->board_type == BOARD_TYPE_PCB112) {
|
|
phy_write(phydev, 0, 31, 0x10);
|
|
phy_write(phydev, 0, 18, 0x80F0);
|
|
while (phy_read(phydev, 0, 18) & 0x8000)
|
|
;
|
|
phy_write(phydev, 0, 31, 0);
|
|
}
|
|
if (gd->board_type == BOARD_TYPE_PCB111) {
|
|
phy_write(phydev, 0, 31, 0x10);
|
|
phy_write(phydev, 0, 18, 0x80A0);
|
|
while (phy_read(phydev, 0, 18) & 0x8000)
|
|
;
|
|
phy_write(phydev, 0, 14, 0x800);
|
|
phy_write(phydev, 0, 31, 0);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
void board_debug_uart_init(void)
|
|
{
|
|
/* too early for the pinctrl driver, so configure the UART pins here */
|
|
vcoreiii_gpio_set_alternate(10, 1);
|
|
vcoreiii_gpio_set_alternate(11, 1);
|
|
}
|
|
|
|
static void do_board_detect(void)
|
|
{
|
|
int i;
|
|
u16 pval;
|
|
|
|
/* MIIM 1 + 2 MDC/MDIO */
|
|
for (i = 56; i < 60; i++)
|
|
vcoreiii_gpio_set_alternate(i, 1);
|
|
|
|
/* small delay for settling the pins */
|
|
mdelay(30);
|
|
|
|
if (mscc_phy_rd(0, 0x10, 0x3, &pval) == 0 &&
|
|
((pval >> 4) & 0x3F) == 0x3c) {
|
|
gd->board_type = BOARD_TYPE_PCB112; /* Serval2-NID */
|
|
} else if (mscc_phy_rd(1, 0x0, 0x3, &pval) == 0 &&
|
|
((pval >> 4) & 0x3F) == 0x3c) {
|
|
gd->board_type = BOARD_TYPE_PCB110; /* Jr2-24 */
|
|
} else {
|
|
/* Fall-back */
|
|
gd->board_type = BOARD_TYPE_PCB111; /* Jr2-48 */
|
|
}
|
|
}
|
|
|
|
#if defined(CONFIG_MULTI_DTB_FIT)
|
|
int board_fit_config_name_match(const char *name)
|
|
{
|
|
if (gd->board_type == BOARD_TYPE_PCB110 &&
|
|
strcmp(name, "jr2_pcb110") == 0)
|
|
return 0;
|
|
|
|
if (gd->board_type == BOARD_TYPE_PCB111 &&
|
|
strcmp(name, "jr2_pcb111") == 0)
|
|
return 0;
|
|
|
|
if (gd->board_type == BOARD_TYPE_PCB112 &&
|
|
strcmp(name, "serval2_pcb112") == 0)
|
|
return 0;
|
|
|
|
return -1;
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_DTB_RESELECT)
|
|
int embedded_dtb_select(void)
|
|
{
|
|
do_board_detect();
|
|
fdtdec_setup();
|
|
|
|
return 0;
|
|
}
|
|
#endif
|