mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-11 07:34:31 +00:00
c2120fbfbc
The sandburst-specific i2c drivers have been deleted, conflict was just over the SPDX conversion. Conflicts: board/sandburst/common/ppc440gx_i2c.c board/sandburst/common/ppc440gx_i2c.h Signed-off-by: Tom Rini <trini@ti.com>
325 lines
12 KiB
C
325 lines
12 KiB
C
/*
|
|
* (C) Copyright 2007
|
|
* Stefan Roese, DENX Software Engineering, sr@denx.de.
|
|
*
|
|
* (C) Copyright 2004 Paul Reynolds <PaulReynolds@lhsolutions.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/************************************************************************
|
|
* katmai.h - configuration for AMCC Katmai (440SPe)
|
|
***********************************************************************/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* High Level Configuration Options
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_KATMAI 1 /* Board is Katmai */
|
|
#define CONFIG_4xx 1 /* ... PPC4xx family */
|
|
#define CONFIG_440 1 /* ... PPC440 family */
|
|
#define CONFIG_440SPE 1 /* Specifc SPe support */
|
|
#define CONFIG_440SPE_REVA 1 /* Support old Rev A. */
|
|
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
|
|
#define CONFIG_SYS_4xx_RESET_TYPE 0x2 /* use chip reset on this board */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0xFFFA0000
|
|
|
|
/*
|
|
* Enable this board for more than 2GB of SDRAM
|
|
*/
|
|
#define CONFIG_PHYS_64BIT
|
|
#define CONFIG_VERY_BIG_RAM
|
|
|
|
/*
|
|
* Include common defines/options for all AMCC eval boards
|
|
*/
|
|
#define CONFIG_HOSTNAME katmai
|
|
#include "amcc-common.h"
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
|
|
#undef CONFIG_SHOW_BOOT_PROGRESS
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Base addresses -- Note these are effective addresses where the
|
|
* actual resources get mapped (not physical addresses)
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH */
|
|
#define CONFIG_SYS_ISRAM_BASE 0x90000000 /* internal SRAM */
|
|
|
|
#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
|
|
#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */
|
|
#define CONFIG_SYS_PCI_TARGBASE CONFIG_SYS_PCI_MEMBASE
|
|
|
|
#define CONFIG_SYS_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */
|
|
#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */
|
|
#define CONFIG_SYS_PCIE_BASE 0xe0000000 /* PCIe UTL regs */
|
|
|
|
#define CONFIG_SYS_PCIE0_CFGBASE 0xc0000000
|
|
#define CONFIG_SYS_PCIE1_CFGBASE 0xc1000000
|
|
#define CONFIG_SYS_PCIE2_CFGBASE 0xc2000000
|
|
#define CONFIG_SYS_PCIE0_XCFGBASE 0xc3000000
|
|
#define CONFIG_SYS_PCIE1_XCFGBASE 0xc3001000
|
|
#define CONFIG_SYS_PCIE2_XCFGBASE 0xc3002000
|
|
|
|
/* base address of inbound PCIe window */
|
|
#define CONFIG_SYS_PCIE_INBOUND_BASE 0x0000000000000000ULL
|
|
|
|
/* System RAM mapped to PCI space */
|
|
#define CONFIG_PCI_SYS_MEM_BUS CONFIG_SYS_SDRAM_BASE
|
|
#define CONFIG_PCI_SYS_MEM_PHYS CONFIG_SYS_SDRAM_BASE
|
|
#define CONFIG_PCI_SYS_MEM_SIZE (1024 * 1024 * 1024)
|
|
|
|
#define CONFIG_SYS_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Initial RAM & stack pointer (placed in internal SRAM)
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_SYS_TEMP_STACK_OCM 1
|
|
#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
|
|
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Serial Port
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
|
|
#undef CONFIG_SYS_EXT_SERIAL_CLOCK
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* DDR SDRAM
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */
|
|
#define SPD_EEPROM_ADDRESS {0x51, 0x52} /* SPD i2c spd addresses*/
|
|
#define CONFIG_DDR_ECC 1 /* with ECC support */
|
|
#define CONFIG_DDR_RQDC_FIXED 0x80000038 /* optimal value found by GDA*/
|
|
#undef CONFIG_STRESS
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* I2C
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
|
|
|
|
#define CONFIG_SYS_SPD_BUS_NUM 0 /* The I2C bus for SPD */
|
|
|
|
#define IIC0_BOOTPROM_ADDR 0x50
|
|
#define IIC0_ALT_BOOTPROM_ADDR 0x54
|
|
|
|
#define CONFIG_SYS_I2C_MULTI_EEPROMS
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR (0x50)
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
|
|
|
|
/* I2C bootstrap EEPROM */
|
|
#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x50
|
|
#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0
|
|
#define CONFIG_4xx_CONFIG_BLOCKSIZE 8
|
|
|
|
/* I2C RTC */
|
|
#define CONFIG_RTC_M41T11 1
|
|
#define CONFIG_SYS_RTC_BUS_NUM 1 /* The I2C bus for RTC */
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
|
#define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* play along with linux */
|
|
|
|
/* I2C DTT */
|
|
#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */
|
|
#define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */
|
|
/*
|
|
* standard dtt sensor configuration - bottom bit will determine local or
|
|
* remote sensor of the ADM1021, the rest determines index into
|
|
* CONFIG_SYS_DTT_ADM1021 array below.
|
|
*/
|
|
#define CONFIG_DTT_SENSORS { 0, 1 }
|
|
|
|
/*
|
|
* ADM1021 temp sensor configuration (see dtt/adm1021.c for details).
|
|
* there will be one entry in this array for each two (dummy) sensors in
|
|
* CONFIG_DTT_SENSORS.
|
|
*
|
|
* For Katmai board:
|
|
* - only one ADM1021
|
|
* - i2c addr 0x18
|
|
* - conversion rate 0x02 = 0.25 conversions/second
|
|
* - ALERT ouput disabled
|
|
* - local temp sensor enabled, min set to 0 deg, max set to 85 deg
|
|
* - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
|
|
*/
|
|
#define CONFIG_SYS_DTT_ADM1021 { { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} }
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Environment
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment uses flash */
|
|
|
|
/*
|
|
* Default environment variables
|
|
*/
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
CONFIG_AMCC_DEF_ENV \
|
|
CONFIG_AMCC_DEF_ENV_POWERPC \
|
|
CONFIG_AMCC_DEF_ENV_NOR_UPD \
|
|
"kernel_addr=ff000000\0" \
|
|
"fdt_addr=ff1e0000\0" \
|
|
"ramdisk_addr=ff200000\0" \
|
|
"pciconfighost=1\0" \
|
|
"pcie_mode=RP:RP:RP\0" \
|
|
""
|
|
|
|
/*
|
|
* Commands additional to the ones defined in amcc-common.h
|
|
*/
|
|
#define CONFIG_CMD_CHIP_CONFIG
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_ECCTEST
|
|
#define CONFIG_CMD_EXT2
|
|
#define CONFIG_CMD_FAT
|
|
#define CONFIG_CMD_PCI
|
|
#define CONFIG_CMD_SDRAM
|
|
#define CONFIG_CMD_SNTP
|
|
|
|
#define CONFIG_IBM_EMAC4_V4 1 /* 440SPe has this EMAC version */
|
|
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
|
|
#define CONFIG_HAS_ETH0
|
|
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
|
|
#define CONFIG_PHY_RESET_DELAY 1000
|
|
#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */
|
|
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH related
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_SYS_FLASH_CFI
|
|
#define CONFIG_FLASH_CFI_DRIVER
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
|
|
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
|
|
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
|
|
|
|
#undef CONFIG_SYS_FLASH_CHECKSUM
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
|
|
#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
|
|
|
|
/* Address and size of Redundant Environment Sector */
|
|
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PCI stuff
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
/* General PCI */
|
|
#define CONFIG_PCI /* include pci support */
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
|
|
#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */
|
|
#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
|
|
#define CONFIG_PCI_CONFIG_HOST_BRIDGE
|
|
|
|
/* Board-specific PCI */
|
|
#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */
|
|
#undef CONFIG_SYS_PCI_MASTER_INIT
|
|
|
|
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
|
|
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
|
|
/* #define CONFIG_SYS_PCI_SUBSYS_ID CONFIG_SYS_PCI_SUBSYS_DEVICEID */
|
|
|
|
/*
|
|
* NETWORK Support (PCI):
|
|
*/
|
|
/* Support for Intel 82557/82559/82559ER chips. */
|
|
#define CONFIG_EEPRO100
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Xilinx System ACE support
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_SYSTEMACE 1 /* Enable SystemACE support */
|
|
#define CONFIG_SYS_SYSTEMACE_WIDTH 16 /* Data bus width is 16 */
|
|
#define CONFIG_SYS_SYSTEMACE_BASE CONFIG_SYS_ACE_BASE
|
|
#define CONFIG_DOS_PARTITION 1
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* External Bus Controller (EBC) Setup
|
|
*----------------------------------------------------------------------*/
|
|
|
|
/* Memory Bank 0 (Flash) initialization */
|
|
#define CONFIG_SYS_EBC_PB0AP (EBC_BXAP_BME_DISABLED | \
|
|
EBC_BXAP_TWT_ENCODE(7) | \
|
|
EBC_BXAP_BCE_DISABLE | \
|
|
EBC_BXAP_BCT_2TRANS | \
|
|
EBC_BXAP_CSN_ENCODE(0) | \
|
|
EBC_BXAP_OEN_ENCODE(0) | \
|
|
EBC_BXAP_WBN_ENCODE(0) | \
|
|
EBC_BXAP_WBF_ENCODE(0) | \
|
|
EBC_BXAP_TH_ENCODE(0) | \
|
|
EBC_BXAP_RE_DISABLED | \
|
|
EBC_BXAP_SOR_DELAYED | \
|
|
EBC_BXAP_BEM_WRITEONLY | \
|
|
EBC_BXAP_PEN_DISABLED)
|
|
#define CONFIG_SYS_EBC_PB0CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) | \
|
|
EBC_BXCR_BS_16MB | \
|
|
EBC_BXCR_BU_RW | \
|
|
EBC_BXCR_BW_16BIT)
|
|
|
|
/* Memory Bank 1 (Xilinx System ACE controller) initialization */
|
|
#define CONFIG_SYS_EBC_PB1AP (EBC_BXAP_BME_DISABLED | \
|
|
EBC_BXAP_TWT_ENCODE(4) | \
|
|
EBC_BXAP_BCE_DISABLE | \
|
|
EBC_BXAP_BCT_2TRANS | \
|
|
EBC_BXAP_CSN_ENCODE(0) | \
|
|
EBC_BXAP_OEN_ENCODE(0) | \
|
|
EBC_BXAP_WBN_ENCODE(0) | \
|
|
EBC_BXAP_WBF_ENCODE(0) | \
|
|
EBC_BXAP_TH_ENCODE(0) | \
|
|
EBC_BXAP_RE_DISABLED | \
|
|
EBC_BXAP_SOR_NONDELAYED | \
|
|
EBC_BXAP_BEM_WRITEONLY | \
|
|
EBC_BXAP_PEN_DISABLED)
|
|
#define CONFIG_SYS_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_ACE_BASE) | \
|
|
EBC_BXCR_BS_1MB | \
|
|
EBC_BXCR_BU_RW | \
|
|
EBC_BXCR_BW_16BIT)
|
|
|
|
/*-------------------------------------------------------------------------
|
|
* Initialize EBC CONFIG -
|
|
* Keep the Default value, but the bit PDT which has to be set to 1 ?TBC
|
|
* default value : 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000
|
|
*-------------------------------------------------------------------------*/
|
|
#define CONFIG_SYS_EBC_CFG (EBC_CFG_LE_UNLOCK | \
|
|
EBC_CFG_PTD_ENABLE | \
|
|
EBC_CFG_RTC_16PERCLK | \
|
|
EBC_CFG_ATC_PREVIOUS | \
|
|
EBC_CFG_DTC_PREVIOUS | \
|
|
EBC_CFG_CTC_PREVIOUS | \
|
|
EBC_CFG_OEO_PREVIOUS | \
|
|
EBC_CFG_EMC_DEFAULT | \
|
|
EBC_CFG_PME_DISABLE | \
|
|
EBC_CFG_PR_16)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* GPIO Setup
|
|
*----------------------------------------------------------------------*/
|
|
#define CONFIG_SYS_GPIO_PCIE_PRESENT0 17
|
|
#define CONFIG_SYS_GPIO_PCIE_PRESENT1 21
|
|
#define CONFIG_SYS_GPIO_PCIE_PRESENT2 23
|
|
#define CONFIG_SYS_GPIO_RS232_FORCEOFF 30
|
|
|
|
#define CONFIG_SYS_PFC0 (GPIO_VAL(CONFIG_SYS_GPIO_PCIE_PRESENT0) | \
|
|
GPIO_VAL(CONFIG_SYS_GPIO_PCIE_PRESENT1) | \
|
|
GPIO_VAL(CONFIG_SYS_GPIO_PCIE_PRESENT2) | \
|
|
GPIO_VAL(CONFIG_SYS_GPIO_RS232_FORCEOFF))
|
|
#define CONFIG_SYS_GPIO_OR GPIO_VAL(CONFIG_SYS_GPIO_RS232_FORCEOFF)
|
|
#define CONFIG_SYS_GPIO_TCR GPIO_VAL(CONFIG_SYS_GPIO_RS232_FORCEOFF)
|
|
#define CONFIG_SYS_GPIO_ODR 0
|
|
|
|
#endif /* __CONFIG_H */
|