mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-18 02:38:56 +00:00
6b0071c110
Create board support for GE PPD, based on mx53loco. Use mx53ppd_defconfig make target to configure for this board. Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
248 lines
7.1 KiB
C
248 lines
7.1 KiB
C
/*
|
|
* Copyright (C) 2011 Freescale Semiconductor, Inc.
|
|
* Jason Liu <r64343@freescale.com>
|
|
*
|
|
* Configuration settings for Freescale MX53 low cost board.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#include <asm/arch/imx-regs.h>
|
|
|
|
#define CONSOLE_DEV "ttymxc0"
|
|
|
|
#define CONFIG_CMDLINE_TAG
|
|
#define CONFIG_SETUP_MEMORY_TAGS
|
|
#define CONFIG_INITRD_TAG
|
|
|
|
#define CONFIG_SYS_FSL_CLK
|
|
|
|
/* Size of malloc() pool */
|
|
#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
|
|
|
|
#define CONFIG_HW_WATCHDOG
|
|
#define CONFIG_IMX_WATCHDOG
|
|
#define CONFIG_WATCHDOG_TIMEOUT_MSECS 8000
|
|
|
|
#define CONFIG_MISC_INIT_R
|
|
#define CONFIG_BOARD_LATE_INIT
|
|
#define CONFIG_MXC_GPIO
|
|
#define CONFIG_REVISION_TAG
|
|
|
|
#define CONFIG_MXC_UART
|
|
#define CONFIG_MXC_UART_BASE UART1_BASE
|
|
|
|
/* MMC Configs */
|
|
#define CONFIG_FSL_ESDHC
|
|
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
|
|
#define CONFIG_SYS_FSL_ESDHC_NUM 2
|
|
|
|
#define CONFIG_SUPPORT_RAW_INITRD /* bootz raw initrd support */
|
|
|
|
/* Eth Configs */
|
|
#define CONFIG_MII
|
|
|
|
#define CONFIG_FEC_MXC
|
|
#define IMX_FEC_BASE FEC_BASE_ADDR
|
|
#define CONFIG_FEC_MXC_PHYADDR 0x1F
|
|
|
|
/* USB Configs */
|
|
#define CONFIG_USB_EHCI_MX5
|
|
#define CONFIG_USB_HOST_ETHER
|
|
#define CONFIG_USB_ETHER_ASIX
|
|
#define CONFIG_USB_ETHER_MCS7830
|
|
#define CONFIG_USB_ETHER_SMSC95XX
|
|
#define CONFIG_MXC_USB_PORT 1
|
|
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
|
|
#define CONFIG_MXC_USB_FLAGS 0
|
|
|
|
#define CONFIG_SYS_RTC_BUS_NUM 2
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x30
|
|
|
|
/* I2C Configs */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_MXC
|
|
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
|
|
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
|
|
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
|
|
|
|
/* PMIC Controller */
|
|
#define CONFIG_POWER
|
|
#define CONFIG_POWER_I2C
|
|
#define CONFIG_DIALOG_POWER
|
|
#define CONFIG_POWER_FSL
|
|
#define CONFIG_POWER_FSL_MC13892
|
|
#define CONFIG_SYS_DIALOG_PMIC_I2C_ADDR 0x48
|
|
#define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x8
|
|
|
|
/* allow to overwrite serial and ethaddr */
|
|
#define CONFIG_ENV_OVERWRITE
|
|
#define CONFIG_CONS_INDEX 1
|
|
#define CONFIG_BAUDRATE 115200
|
|
|
|
/* Command definition */
|
|
#define CONFIG_SUPPORT_RAW_INITRD
|
|
|
|
#define CONFIG_ETHPRIME "FEC0"
|
|
|
|
#define CONFIG_LOADADDR 0x72000000 /* loadaddr env var */
|
|
#define CONFIG_SYS_TEXT_BASE 0x77800000
|
|
|
|
#define PPD_CONFIG_NFS \
|
|
"nfsserver=192.168.252.95\0" \
|
|
"gatewayip=192.168.252.95\0" \
|
|
"netmask=255.255.255.0\0" \
|
|
"ipaddr=192.168.252.99\0" \
|
|
"kernsize=0x2000\0" \
|
|
"use_dhcp=0\0" \
|
|
"nfsroot=/opt/springdale/rd\0" \
|
|
"bootargs_nfs=setenv bootargs ${bootargs} root=/dev/nfs " \
|
|
"${kern_ipconf} nfsroot=${nfsserver}:${nfsroot},v3,tcp rw\0" \
|
|
"choose_ip=if test $use_dhcp = 1; then set kern_ipconf ip=dhcp; " \
|
|
"set getcmd dhcp; else set kern_ipconf " \
|
|
"ip=${ipaddr}:${nfsserver}:${gatewayip}:${netmask}::eth0:off; " \
|
|
"set getcmd tftp; fi\0" \
|
|
"nfs=run choose_ip setargs bootargs_nfs; ${getcmd} ${loadaddr} " \
|
|
"${nfsserver}:${image}; bootm ${loadaddr}\0" \
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
PPD_CONFIG_NFS \
|
|
"bootlimit=10\0" \
|
|
"image=/boot/fitImage\0" \
|
|
"fdt_high=0xffffffff\0" \
|
|
"dev=mmc\0" \
|
|
"devnum=0\0" \
|
|
"rootdev=mmcblk0p\0" \
|
|
"quiet=quiet loglevel=0\0" \
|
|
"console=" CONSOLE_DEV "\0" \
|
|
"lvds=ldb\0" \
|
|
"setargs=setenv bootargs ${lvds} jtag=on mem=2G " \
|
|
"vt.global_cursor_default=0 bootcause=${bootcause} ${quiet} " \
|
|
"console=${console} ${rtc_status}\0" \
|
|
"bootargs_emmc=setenv bootargs root=/dev/${rootdev}${partnum} ro " \
|
|
"rootwait ${bootargs}\0" \
|
|
"doquiet=if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; " \
|
|
"then setenv quiet; fi\0" \
|
|
"hasfirstboot=ext2load ${dev} ${devnum}:${partnum} 0x7000A000 " \
|
|
"/boot/bootcause/firstboot\0" \
|
|
"swappartitions=setexpr partnum 3 - ${partnum}\0" \
|
|
"failbootcmd=" \
|
|
"ppd_lcd_enable; " \
|
|
"msg=\"Monitor failed to start. " \
|
|
"Try again, or contact GE Service for support.\"; " \
|
|
"echo $msg; " \
|
|
"setenv stdout vga; " \
|
|
"echo \"\n\n\n\n \" $msg; " \
|
|
"setenv stdout serial; " \
|
|
"mw.b 0x7000A000 0xbc; " \
|
|
"mw.b 0x7000A001 0x00; " \
|
|
"ext4write ${dev} ${devnum}:5 0x7000A000 /boot/failures 2\0" \
|
|
"altbootcmd=" \
|
|
"run doquiet; " \
|
|
"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
|
|
"run hasfirstboot || setenv partnum 0; " \
|
|
"if test ${partnum} != 0; then " \
|
|
"setenv bootcause REVERT; " \
|
|
"run swappartitions loadimage doboot; " \
|
|
"fi; " \
|
|
"run failbootcmd\0" \
|
|
"loadimage=" \
|
|
"ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
|
|
"doboot=" \
|
|
"echo Booting from ${dev}:${devnum}:${partnum} ...; " \
|
|
"run setargs; " \
|
|
"run bootargs_emmc; " \
|
|
"bootm ${loadaddr}\0" \
|
|
"tryboot=" \
|
|
"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
|
|
"run loadimage || run swappartitions && run loadimage || " \
|
|
"setenv partnum 0 && echo MISSING IMAGE;" \
|
|
"run doboot; " \
|
|
"run failbootcmd\0" \
|
|
"video-mode=" \
|
|
"lcd:800x480-24@60,monitor=lcd\0" \
|
|
|
|
#define CONFIG_MMCBOOTCOMMAND \
|
|
"if mmc dev ${devnum}; then " \
|
|
"run doquiet; " \
|
|
"run tryboot; " \
|
|
"fi; " \
|
|
|
|
#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND
|
|
|
|
#define CONFIG_ARP_TIMEOUT 200UL
|
|
|
|
/* Miscellaneous configurable options */
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_AUTO_COMPLETE
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
|
|
#define CONFIG_SYS_MAXARGS 48 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x70000000
|
|
#define CONFIG_SYS_MEMTEST_END 0x70010000
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
|
|
|
|
#define CONFIG_CMDLINE_EDITING
|
|
|
|
/* Physical Memory Map */
|
|
#define CONFIG_NR_DRAM_BANKS 2
|
|
#define PHYS_SDRAM_1 CSD0_BASE_ADDR
|
|
#define PHYS_SDRAM_1_SIZE (gd->bd->bi_dram[0].size)
|
|
#define PHYS_SDRAM_2 CSD1_BASE_ADDR
|
|
#define PHYS_SDRAM_2_SIZE (gd->bd->bi_dram[1].size)
|
|
#define PHYS_SDRAM_SIZE (gd->ram_size)
|
|
|
|
#define CONFIG_SYS_SDRAM_BASE (PHYS_SDRAM_1)
|
|
#define CONFIG_SYS_INIT_RAM_ADDR (IRAM_BASE_ADDR)
|
|
#define CONFIG_SYS_INIT_RAM_SIZE (IRAM_SIZE)
|
|
|
|
#define CONFIG_SYS_INIT_SP_OFFSET \
|
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_ADDR \
|
|
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
|
|
|
|
/* FLASH and environment organization */
|
|
#define CONFIG_ENV_OFFSET (6 * 64 * 1024)
|
|
#define CONFIG_ENV_SIZE (8 * 1024)
|
|
#define CONFIG_ENV_IS_IN_MMC
|
|
#define CONFIG_SYS_MMC_ENV_DEV 0
|
|
|
|
#define CONFIG_CMD_FUSE
|
|
#define CONFIG_FSL_IIM
|
|
|
|
#define CONFIG_SYS_I2C_SPEED 100000
|
|
|
|
/* I2C1 */
|
|
#define CONFIG_SYS_NUM_I2C_BUSES 9
|
|
#define CONFIG_SYS_I2C_MAX_HOPS 1
|
|
#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
|
|
{0, {{I2C_MUX_PCA9547, 0x70, 0} } }, \
|
|
{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
|
|
{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
|
|
{0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \
|
|
{0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \
|
|
{0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \
|
|
{0, {{I2C_MUX_PCA9547, 0x70, 6} } }, \
|
|
{0, {{I2C_MUX_PCA9547, 0x70, 7} } }, \
|
|
}
|
|
|
|
#define CONFIG_BCH
|
|
|
|
#define CONFIG_BOOTCOUNT_LIMIT
|
|
|
|
/* Backlight Control */
|
|
#define CONFIG_PWM_IMX
|
|
#define CONFIG_IMX6_PWM_PER_CLK 66666000
|
|
|
|
/* Framebuffer and LCD */
|
|
#ifdef CONFIG_VIDEO
|
|
#define CONFIG_VIDEO_IPUV3
|
|
#endif
|
|
|
|
#endif /* __CONFIG_H */
|