mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-18 02:38:56 +00:00
541d57663f
The CONFIG_SYS_DPAA_QBMAN define is used by DPAA1 freescale SOCs to add device tree fixups that allow deep sleep in Linux. The define was placed in header files included by a number of boards, but was not explicitly documented in any of the Kconfigs. A description was added to the drivers/networking menuconfig and default selection for current SOCs that have this part Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
289 lines
8.8 KiB
C
289 lines
8.8 KiB
C
/*
|
|
* Copyright 2016 Freescale Semiconductor
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __LS1046A_COMMON_H
|
|
#define __LS1046A_COMMON_H
|
|
|
|
/* SPL build */
|
|
#ifdef CONFIG_SPL_BUILD
|
|
#define SPL_NO_QBMAN
|
|
#define SPL_NO_FMAN
|
|
#define SPL_NO_ENV
|
|
#define SPL_NO_MISC
|
|
#define SPL_NO_QSPI
|
|
#define SPL_NO_USB
|
|
#define SPL_NO_SATA
|
|
#endif
|
|
#if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT))
|
|
#define SPL_NO_MMC
|
|
#endif
|
|
#if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT))
|
|
#define SPL_NO_IFC
|
|
#endif
|
|
|
|
#define CONFIG_REMAKE_ELF
|
|
#define CONFIG_FSL_LAYERSCAPE
|
|
#define CONFIG_MP
|
|
#define CONFIG_GICV2
|
|
|
|
#include <asm/arch/config.h>
|
|
#include <asm/arch/stream_id_lsch2.h>
|
|
|
|
/* Link Definitions */
|
|
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
|
|
|
|
#define CONFIG_SUPPORT_RAW_INITRD
|
|
|
|
#define CONFIG_SKIP_LOWLEVEL_INIT
|
|
|
|
#define CONFIG_VERY_BIG_RAM
|
|
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000
|
|
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
|
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
|
|
#define CONFIG_SYS_DDR_BLOCK2_BASE 0x880000000ULL
|
|
|
|
#define CPU_RELEASE_ADDR secondary_boot_func
|
|
|
|
/* Generic Timer Definitions */
|
|
#define COUNTER_FREQUENCY 25000000 /* 25MHz */
|
|
|
|
/* Size of malloc() pool */
|
|
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024)
|
|
|
|
/* Serial Port */
|
|
#define CONFIG_CONS_INDEX 1
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK (get_serial_clock())
|
|
|
|
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
|
|
|
|
/* SD boot SPL */
|
|
#ifdef CONFIG_SD_BOOT
|
|
#define CONFIG_SPL_FRAMEWORK
|
|
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
|
|
#define CONFIG_SPL_LIBCOMMON_SUPPORT
|
|
#define CONFIG_SPL_LIBGENERIC_SUPPORT
|
|
#define CONFIG_SPL_ENV_SUPPORT
|
|
#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
|
|
#define CONFIG_SPL_WATCHDOG_SUPPORT
|
|
#define CONFIG_SPL_I2C_SUPPORT
|
|
#define CONFIG_SPL_SERIAL_SUPPORT
|
|
#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
|
|
|
|
#define CONFIG_SPL_MMC_SUPPORT
|
|
#define CONFIG_SPL_TEXT_BASE 0x10000000
|
|
#define CONFIG_SPL_MAX_SIZE 0x1f000 /* 124 KiB */
|
|
#define CONFIG_SPL_STACK 0x10020000
|
|
#define CONFIG_SPL_PAD_TO 0x21000 /* 132 KiB */
|
|
#define CONFIG_SPL_BSS_START_ADDR 0x8f000000
|
|
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
|
|
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
|
|
CONFIG_SPL_BSS_MAX_SIZE)
|
|
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
|
|
|
|
#ifdef CONFIG_SECURE_BOOT
|
|
#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
|
|
/*
|
|
* HDR would be appended at end of image and copied to DDR along
|
|
* with U-Boot image. Here u-boot max. size is 512K. So if binary
|
|
* size increases then increase this size in case of secure boot as
|
|
* it uses raw u-boot image instead of fit image.
|
|
*/
|
|
#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
|
|
#else
|
|
#define CONFIG_SYS_MONITOR_LEN 0x100000
|
|
#endif /* ifdef CONFIG_SECURE_BOOT */
|
|
#endif
|
|
|
|
/* NAND SPL */
|
|
#ifdef CONFIG_NAND_BOOT
|
|
#define CONFIG_SPL_PBL_PAD
|
|
#define CONFIG_SPL_FRAMEWORK
|
|
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
|
|
#define CONFIG_SPL_LIBCOMMON_SUPPORT
|
|
#define CONFIG_SPL_LIBGENERIC_SUPPORT
|
|
#define CONFIG_SPL_ENV_SUPPORT
|
|
#define CONFIG_SPL_WATCHDOG_SUPPORT
|
|
#define CONFIG_SPL_I2C_SUPPORT
|
|
#define CONFIG_SPL_SERIAL_SUPPORT
|
|
#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
|
|
|
|
#define CONFIG_SPL_NAND_SUPPORT
|
|
#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
|
|
#define CONFIG_SPL_TEXT_BASE 0x10000000
|
|
#define CONFIG_SPL_MAX_SIZE 0x17000 /* 90 KiB */
|
|
#define CONFIG_SPL_STACK 0x1001f000
|
|
#define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
|
|
|
|
#define CONFIG_SPL_BSS_START_ADDR 0x8f000000
|
|
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
|
|
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
|
|
CONFIG_SPL_BSS_MAX_SIZE)
|
|
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
|
|
#define CONFIG_SYS_MONITOR_LEN 0xa0000
|
|
#endif
|
|
|
|
/* I2C */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_MXC
|
|
#define CONFIG_SYS_I2C_MXC_I2C1
|
|
#define CONFIG_SYS_I2C_MXC_I2C2
|
|
#define CONFIG_SYS_I2C_MXC_I2C3
|
|
#define CONFIG_SYS_I2C_MXC_I2C4
|
|
|
|
/* PCIe */
|
|
#define CONFIG_PCIE1 /* PCIE controller 1 */
|
|
#define CONFIG_PCIE2 /* PCIE controller 2 */
|
|
#define CONFIG_PCIE3 /* PCIE controller 3 */
|
|
|
|
#ifdef CONFIG_PCI
|
|
#define CONFIG_PCI_SCAN_SHOW
|
|
#endif
|
|
|
|
/* Command line configuration */
|
|
|
|
/* MMC */
|
|
#ifndef SPL_NO_MMC
|
|
#ifdef CONFIG_MMC
|
|
#define CONFIG_FSL_ESDHC
|
|
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
|
|
#endif
|
|
#endif
|
|
|
|
/* FMan ucode */
|
|
#ifndef SPL_NO_FMAN
|
|
#define CONFIG_SYS_DPAA_FMAN
|
|
#ifdef CONFIG_SYS_DPAA_FMAN
|
|
#define CONFIG_SYS_FM_MURAM_SIZE 0x60000
|
|
#endif
|
|
|
|
#ifdef CONFIG_SD_BOOT
|
|
/*
|
|
* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
|
|
* about 1MB (2048 blocks), Env is stored after the image, and the env size is
|
|
* 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 18432(0x4800).
|
|
*/
|
|
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
|
|
#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x4800)
|
|
#elif defined(CONFIG_QSPI_BOOT)
|
|
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
|
|
#define CONFIG_SYS_FMAN_FW_ADDR 0x40900000
|
|
#define CONFIG_ENV_SPI_BUS 0
|
|
#define CONFIG_ENV_SPI_CS 0
|
|
#define CONFIG_ENV_SPI_MAX_HZ 1000000
|
|
#define CONFIG_ENV_SPI_MODE 0x03
|
|
#elif defined(CONFIG_NAND_BOOT)
|
|
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
|
|
#define CONFIG_SYS_FMAN_FW_ADDR (36 * CONFIG_SYS_NAND_BLOCK_SIZE)
|
|
#else
|
|
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
|
|
#define CONFIG_SYS_FMAN_FW_ADDR 0x60900000
|
|
#endif
|
|
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
|
|
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
|
|
#endif
|
|
|
|
/* Miscellaneous configurable options */
|
|
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
|
|
|
|
#define CONFIG_HWCONFIG
|
|
#define HWCONFIG_BUFFER_SIZE 128
|
|
|
|
#include <config_distro_defaults.h>
|
|
#ifndef CONFIG_SPL_BUILD
|
|
#define BOOT_TARGET_DEVICES(func) \
|
|
func(MMC, mmc, 0) \
|
|
func(USB, usb, 0)
|
|
#include <config_distro_bootcmd.h>
|
|
#endif
|
|
|
|
#ifndef SPL_NO_MISC
|
|
/* Initial environment variables */
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
|
|
"ramdisk_addr=0x800000\0" \
|
|
"ramdisk_size=0x2000000\0" \
|
|
"fdt_high=0xffffffffffffffff\0" \
|
|
"initrd_high=0xffffffffffffffff\0" \
|
|
"fdt_addr=0x64f00000\0" \
|
|
"kernel_addr=0x65000000\0" \
|
|
"scriptaddr=0x80000000\0" \
|
|
"scripthdraddr=0x80080000\0" \
|
|
"fdtheader_addr_r=0x80100000\0" \
|
|
"kernelheader_addr_r=0x80200000\0" \
|
|
"load_addr=0xa0000000\0" \
|
|
"kernel_addr_r=0x81000000\0" \
|
|
"fdt_addr_r=0x90000000\0" \
|
|
"ramdisk_addr_r=0xa0000000\0" \
|
|
"kernel_start=0x1000000\0" \
|
|
"kernelheader_start=0x800000\0" \
|
|
"kernel_load=0xa0000000\0" \
|
|
"kernel_size=0x2800000\0" \
|
|
"kernelheader_size=0x40000\0" \
|
|
"kernel_addr_sd=0x8000\0" \
|
|
"kernel_size_sd=0x14000\0" \
|
|
"kernelhdr_addr_sd=0x4000\0" \
|
|
"kernelhdr_size_sd=0x10\0" \
|
|
"console=ttyS0,115200\0" \
|
|
CONFIG_MTDPARTS_DEFAULT "\0" \
|
|
BOOTENV \
|
|
"boot_scripts=ls1046ardb_boot.scr\0" \
|
|
"boot_script_hdr=hdr_ls1046ardb_bs.out\0" \
|
|
"scan_dev_for_boot_part=" \
|
|
"part list ${devtype} ${devnum} devplist; " \
|
|
"env exists devplist || setenv devplist 1; " \
|
|
"for distro_bootpart in ${devplist}; do " \
|
|
"if fstype ${devtype} " \
|
|
"${devnum}:${distro_bootpart} " \
|
|
"bootfstype; then " \
|
|
"run scan_dev_for_boot; " \
|
|
"fi; " \
|
|
"done\0" \
|
|
"scan_dev_for_boot=" \
|
|
"echo Scanning ${devtype} " \
|
|
"${devnum}:${distro_bootpart}...; " \
|
|
"for prefix in ${boot_prefixes}; do " \
|
|
"run scan_dev_for_scripts; " \
|
|
"done;" \
|
|
"\0" \
|
|
"boot_a_script=" \
|
|
"load ${devtype} ${devnum}:${distro_bootpart} " \
|
|
"${scriptaddr} ${prefix}${script}; " \
|
|
"env exists secureboot && load ${devtype} " \
|
|
"${devnum}:${distro_bootpart} " \
|
|
"${scripthdraddr} ${prefix}${boot_script_hdr} " \
|
|
"&& esbc_validate ${scripthdraddr};" \
|
|
"source ${scriptaddr}\0" \
|
|
"qspi_bootcmd=echo Trying load from qspi..;" \
|
|
"sf probe && sf read $load_addr " \
|
|
"$kernel_start $kernel_size; env exists secureboot " \
|
|
"&& sf read $kernelheader_addr_r $kernelheader_start " \
|
|
"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
|
|
"bootm $load_addr#$board\0" \
|
|
"sd_bootcmd=echo Trying load from SD ..;" \
|
|
"mmcinfo; mmc read $load_addr " \
|
|
"$kernel_addr_sd $kernel_size_sd && " \
|
|
"env exists secureboot && mmc read $kernelheader_addr_r " \
|
|
"$kernelhdr_addr_sd $kernelhdr_size_sd " \
|
|
" && esbc_validate ${kernelheader_addr_r};" \
|
|
"bootm $load_addr#$board\0"
|
|
|
|
#endif
|
|
|
|
/* Monitor Command Prompt */
|
|
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
|
|
#define CONFIG_SYS_LONGHELP
|
|
|
|
#define CONFIG_AUTO_COMPLETE
|
|
#define CONFIG_SYS_MAXARGS 64 /* max command args */
|
|
|
|
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
|
|
|
|
#include <asm/arch/soc.h>
|
|
|
|
#endif /* __LS1046A_COMMON_H */
|