u-boot/arch/arm/cpu/armv7/am33xx/board.c
Tom Rini 196311dc72 arm:am33xx: Rework s_init and add board_early_init_f
With the changes to the i2c framework (and adopting the omap24xx_i2c
driver to them) we can no longer call i2c functions prior to gd having
been set and cleared.  When SPL booting, this is handled by setting gd
to point to SRAM in s_init.  However in the cases where we are loaded
directly by ROM (memory mapped NOR or QSPI) we need to make use of the
normal hooks to slightly delay these calls.

Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06 17:46:14 -04:00

265 lines
6.3 KiB
C

/*
* board.c
*
* Common board functions for AM33XX based boards
*
* Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <errno.h>
#include <spl.h>
#include <asm/arch/cpu.h>
#include <asm/arch/hardware.h>
#include <asm/arch/omap.h>
#include <asm/arch/ddr_defs.h>
#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mem.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/sys_proto.h>
#include <asm/io.h>
#include <asm/emif.h>
#include <asm/gpio.h>
#include <i2c.h>
#include <miiphy.h>
#include <cpsw.h>
#include <asm/errno.h>
#include <linux/compiler.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
#include <linux/usb/musb.h>
#include <asm/omap_musb.h>
#include <asm/davinci_rtc.h>
DECLARE_GLOBAL_DATA_PTR;
static const struct gpio_bank gpio_bank_am33xx[] = {
{ (void *)AM33XX_GPIO0_BASE, METHOD_GPIO_24XX },
{ (void *)AM33XX_GPIO1_BASE, METHOD_GPIO_24XX },
{ (void *)AM33XX_GPIO2_BASE, METHOD_GPIO_24XX },
{ (void *)AM33XX_GPIO3_BASE, METHOD_GPIO_24XX },
#ifdef CONFIG_AM43XX
{ (void *)AM33XX_GPIO4_BASE, METHOD_GPIO_24XX },
{ (void *)AM33XX_GPIO5_BASE, METHOD_GPIO_24XX },
#endif
};
const struct gpio_bank *const omap_gpio_bank = gpio_bank_am33xx;
#if defined(CONFIG_OMAP_HSMMC) && !defined(CONFIG_SPL_BUILD)
int cpu_mmc_init(bd_t *bis)
{
int ret;
ret = omap_mmc_init(0, 0, 0, -1, -1);
if (ret)
return ret;
return omap_mmc_init(1, 0, 0, -1, -1);
}
#endif
/* AM33XX has two MUSB controllers which can be host or gadget */
#if (defined(CONFIG_MUSB_GADGET) || defined(CONFIG_MUSB_HOST)) && \
(defined(CONFIG_AM335X_USB0) || defined(CONFIG_AM335X_USB1))
static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
/* USB 2.0 PHY Control */
#define CM_PHY_PWRDN (1 << 0)
#define CM_PHY_OTG_PWRDN (1 << 1)
#define OTGVDET_EN (1 << 19)
#define OTGSESSENDEN (1 << 20)
static void am33xx_usb_set_phy_power(u8 on, u32 *reg_addr)
{
if (on) {
clrsetbits_le32(reg_addr, CM_PHY_PWRDN | CM_PHY_OTG_PWRDN,
OTGVDET_EN | OTGSESSENDEN);
} else {
clrsetbits_le32(reg_addr, 0, CM_PHY_PWRDN | CM_PHY_OTG_PWRDN);
}
}
static struct musb_hdrc_config musb_config = {
.multipoint = 1,
.dyn_fifo = 1,
.num_eps = 16,
.ram_bits = 12,
};
#ifdef CONFIG_AM335X_USB0
static void am33xx_otg0_set_phy_power(u8 on)
{
am33xx_usb_set_phy_power(on, &cdev->usb_ctrl0);
}
struct omap_musb_board_data otg0_board_data = {
.set_phy_power = am33xx_otg0_set_phy_power,
};
static struct musb_hdrc_platform_data otg0_plat = {
.mode = CONFIG_AM335X_USB0_MODE,
.config = &musb_config,
.power = 50,
.platform_ops = &musb_dsps_ops,
.board_data = &otg0_board_data,
};
#endif
#ifdef CONFIG_AM335X_USB1
static void am33xx_otg1_set_phy_power(u8 on)
{
am33xx_usb_set_phy_power(on, &cdev->usb_ctrl1);
}
struct omap_musb_board_data otg1_board_data = {
.set_phy_power = am33xx_otg1_set_phy_power,
};
static struct musb_hdrc_platform_data otg1_plat = {
.mode = CONFIG_AM335X_USB1_MODE,
.config = &musb_config,
.power = 50,
.platform_ops = &musb_dsps_ops,
.board_data = &otg1_board_data,
};
#endif
#endif
int arch_misc_init(void)
{
#ifdef CONFIG_AM335X_USB0
musb_register(&otg0_plat, &otg0_board_data,
(void *)USB0_OTG_BASE);
#endif
#ifdef CONFIG_AM335X_USB1
musb_register(&otg1_plat, &otg1_board_data,
(void *)USB1_OTG_BASE);
#endif
return 0;
}
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
/*
* In the case of non-SPL based booting we'll want to call these
* functions a tiny bit later as it will require gd to be set and cleared
* and that's not true in s_init in this case so we cannot do it there.
*/
int board_early_init_f(void)
{
prcm_init();
set_mux_conf_regs();
return 0;
}
/*
* This function is the place to do per-board things such as ramp up the
* MPU clock frequency.
*/
__weak void am33xx_spl_board_init(void)
{
do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
}
#if defined(CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC)
static void rtc32k_enable(void)
{
struct davinci_rtc *rtc = (struct davinci_rtc *)RTC_BASE;
/*
* Unlock the RTC's registers. For more details please see the
* RTC_SS section of the TRM. In order to unlock we need to
* write these specific values (keys) in this order.
*/
writel(RTC_KICK0R_WE, &rtc->kick0r);
writel(RTC_KICK1R_WE, &rtc->kick1r);
/* Enable the RTC 32K OSC by setting bits 3 and 6. */
writel((1 << 3) | (1 << 6), &rtc->osc);
}
#endif
static void uart_soft_reset(void)
{
struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
u32 regval;
regval = readl(&uart_base->uartsyscfg);
regval |= UART_RESET;
writel(regval, &uart_base->uartsyscfg);
while ((readl(&uart_base->uartsyssts) &
UART_CLK_RUNNING_MASK) != UART_CLK_RUNNING_MASK)
;
/* Disable smart idle */
regval = readl(&uart_base->uartsyscfg);
regval |= UART_SMART_IDLE_EN;
writel(regval, &uart_base->uartsyscfg);
}
static void watchdog_disable(void)
{
struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
writel(0xAAAA, &wdtimer->wdtwspr);
while (readl(&wdtimer->wdtwwps) != 0x0)
;
writel(0x5555, &wdtimer->wdtwspr);
while (readl(&wdtimer->wdtwwps) != 0x0)
;
}
void s_init(void)
{
/*
* The ROM will only have set up sufficient pinmux to allow for the
* first 4KiB NOR to be read, we must finish doing what we know of
* the NOR mux in this space in order to continue.
*/
#ifdef CONFIG_NOR_BOOT
enable_norboot_pin_mux();
#endif
/*
* Save the boot parameters passed from romcode.
* We cannot delay the saving further than this,
* to prevent overwrites.
*/
#ifdef CONFIG_SPL_BUILD
save_omap_boot_params();
#endif
watchdog_disable();
timer_init();
set_uart_mux_conf();
setup_clocks_for_console();
uart_soft_reset();
#if defined(CONFIG_NOR_BOOT) || defined(CONFIG_QSPI_BOOT)
gd->baudrate = CONFIG_BAUDRATE;
serial_init();
gd->have_console = 1;
#elif defined(CONFIG_SPL_BUILD)
gd = &gdata;
preloader_console_init();
#endif
#if defined(CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC)
/* Enable RTC32K clock */
rtc32k_enable();
#endif
#ifdef CONFIG_SPL_BUILD
board_early_init_f();
sdram_init();
#endif
}
#endif
#ifndef CONFIG_SYS_DCACHE_OFF
void enable_caches(void)
{
/* Enable D-cache. I-cache is already enabled in start.S */
dcache_enable();
}
#endif /* !CONFIG_SYS_DCACHE_OFF */