mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-11 07:34:31 +00:00
aa6e94deab
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM namespace do not easily transition to Kconfig. In many cases they likely should come from the device tree instead. Move these out of CONFIG namespace and in to CFG namespace. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
199 lines
4.7 KiB
C
199 lines
4.7 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright 2014 Freescale Semiconductor, Inc.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <fsl_ddr_sdram.h>
|
|
#include <fsl_ddr_dimm_params.h>
|
|
#include <init.h>
|
|
#include <log.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <linux/delay.h>
|
|
#include "ddr.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
void fsl_ddr_board_options(memctl_options_t *popts,
|
|
dimm_params_t *pdimm,
|
|
unsigned int ctrl_num)
|
|
{
|
|
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
|
|
ulong ddr_freq;
|
|
|
|
if (ctrl_num > 3) {
|
|
printf("Not supported controller number %d\n", ctrl_num);
|
|
return;
|
|
}
|
|
if (!pdimm->n_ranks)
|
|
return;
|
|
|
|
pbsp = udimms[0];
|
|
|
|
/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
|
|
* freqency and n_banks specified in board_specific_parameters table.
|
|
*/
|
|
ddr_freq = get_ddr_freq(0) / 1000000;
|
|
while (pbsp->datarate_mhz_high) {
|
|
if (pbsp->n_ranks == pdimm->n_ranks) {
|
|
if (ddr_freq <= pbsp->datarate_mhz_high) {
|
|
popts->clk_adjust = pbsp->clk_adjust;
|
|
popts->wrlvl_start = pbsp->wrlvl_start;
|
|
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
|
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
|
popts->cpo_override = pbsp->cpo_override;
|
|
popts->write_data_delay =
|
|
pbsp->write_data_delay;
|
|
goto found;
|
|
}
|
|
pbsp_highest = pbsp;
|
|
}
|
|
pbsp++;
|
|
}
|
|
|
|
if (pbsp_highest) {
|
|
printf("Error: board specific timing not found for %lu MT/s\n",
|
|
ddr_freq);
|
|
printf("Trying to use the highest speed (%u) parameters\n",
|
|
pbsp_highest->datarate_mhz_high);
|
|
popts->clk_adjust = pbsp_highest->clk_adjust;
|
|
popts->wrlvl_start = pbsp_highest->wrlvl_start;
|
|
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
|
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
|
} else {
|
|
panic("DIMM is not supported by this board");
|
|
}
|
|
found:
|
|
debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
|
|
pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
|
|
|
|
/* force DDR bus width to 32 bits */
|
|
popts->data_bus_width = 1;
|
|
popts->otf_burst_chop_en = 0;
|
|
popts->burst_length = DDR_BL8;
|
|
|
|
/*
|
|
* Factors to consider for half-strength driver enable:
|
|
* - number of DIMMs installed
|
|
*/
|
|
popts->half_strength_driver_enable = 1;
|
|
/*
|
|
* Write leveling override
|
|
*/
|
|
popts->wrlvl_override = 1;
|
|
popts->wrlvl_sample = 0xf;
|
|
|
|
/*
|
|
* Rtt and Rtt_WR override
|
|
*/
|
|
popts->rtt_override = 0;
|
|
|
|
/* Enable ZQ calibration */
|
|
popts->zq_en = 1;
|
|
|
|
#ifdef CONFIG_SYS_FSL_DDR4
|
|
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
|
|
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
|
|
DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */
|
|
#else
|
|
popts->cswl_override = DDR_CSWL_CS0;
|
|
|
|
/* optimize cpo for erratum A-009942 */
|
|
popts->cpo_sample = 0x58;
|
|
|
|
/* DHC_EN =1, ODT = 75 Ohm */
|
|
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
|
|
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
|
|
#endif
|
|
}
|
|
|
|
#ifdef CONFIG_SYS_DDR_RAW_TIMING
|
|
dimm_params_t ddr_raw_timing = {
|
|
.n_ranks = 1,
|
|
.rank_density = 1073741824u,
|
|
.capacity = 1073741824u,
|
|
.primary_sdram_width = 32,
|
|
.ec_sdram_width = 0,
|
|
.registered_dimm = 0,
|
|
.mirrored_dimm = 0,
|
|
.n_row_addr = 15,
|
|
.n_col_addr = 10,
|
|
.n_banks_per_sdram_device = 8,
|
|
.edc_config = 0,
|
|
.burst_lengths_bitmask = 0x0c,
|
|
|
|
.tckmin_x_ps = 1071,
|
|
.caslat_x = 0xfe << 4, /* 5,6,7,8 */
|
|
.taa_ps = 13125,
|
|
.twr_ps = 15000,
|
|
.trcd_ps = 13125,
|
|
.trrd_ps = 7500,
|
|
.trp_ps = 13125,
|
|
.tras_ps = 37500,
|
|
.trc_ps = 50625,
|
|
.trfc_ps = 160000,
|
|
.twtr_ps = 7500,
|
|
.trtp_ps = 7500,
|
|
.refresh_rate_ps = 7800000,
|
|
.tfaw_ps = 37500,
|
|
};
|
|
|
|
int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
|
|
unsigned int controller_number,
|
|
unsigned int dimm_number)
|
|
{
|
|
static const char dimm_model[] = "Fixed DDR on board";
|
|
|
|
if (((controller_number == 0) && (dimm_number == 0)) ||
|
|
((controller_number == 1) && (dimm_number == 0))) {
|
|
memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
|
|
memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
|
|
memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_DEEP_SLEEP)
|
|
void board_mem_sleep_setup(void)
|
|
{
|
|
void __iomem *qixis_base = (void *)QIXIS_BASE;
|
|
|
|
/* does not provide HW signals for power management */
|
|
clrbits_8(qixis_base + 0x21, 0x2);
|
|
udelay(1);
|
|
}
|
|
#endif
|
|
|
|
int fsl_initdram(void)
|
|
{
|
|
phys_size_t dram_size;
|
|
|
|
#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_SPL)
|
|
puts("Initializing DDR....using SPD\n");
|
|
dram_size = fsl_ddr_sdram();
|
|
#else
|
|
dram_size = fsl_ddr_sdram_size();
|
|
#endif
|
|
|
|
#if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD)
|
|
fsl_dp_resume();
|
|
#endif
|
|
|
|
erratum_a008850_post();
|
|
|
|
gd->ram_size = dram_size;
|
|
|
|
return 0;
|
|
}
|
|
|
|
int dram_init_banksize(void)
|
|
{
|
|
gd->bd->bi_dram[0].start = CFG_SYS_SDRAM_BASE;
|
|
gd->bd->bi_dram[0].size = gd->ram_size;
|
|
|
|
return 0;
|
|
}
|