Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-19 11:18:28 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/arch/arm/cpu/armv7/sunxi/board.c
Daniel Kochmański f76eba38b3 sunxi/nand: Add support to the SPL for loading u-boot from internal NAND memory 
This commit adds support to the sunxi SPL to load u-boot from the internal
NAND. Note this only adds support to access the boot partitions to load
u-boot, full NAND support to load the kernel, etc. from the nand data
partition will come later.

Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-29 13:46:36 +02:00

240 lines
6.9 KiB
C
Raw Blame History

/*
* (C) Copyright 2012 Henrik Nordstrom <henrik@henriknordstrom.net>
*
* (C) Copyright 2007-2011
* Allwinner Technology Co., Ltd. <www.allwinnertech.com>
* Tom Cubie <tangliang@allwinnertech.com>
*
* Some init for sunxi platform.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <i2c.h>
#include <serial.h>
#ifdef CONFIG_SPL_BUILD
#include <spl.h>
#endif
#include <asm/gpio.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/timer.h>
#include <linux/compiler.h>
struct fel_stash {
uint32_t sp;
uint32_t lr;
uint32_t cpsr;
uint32_t sctlr;
uint32_t vbar;
uint32_t cr;
};
struct fel_stash fel_stash __attribute__((section(".data")));
static int gpio_init(void)
{
#if CONFIG_CONS_INDEX == 1 && defined(CONFIG_UART0_PORT_F)
#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I)
/* disable GPB22,23 as uart0 tx,rx to avoid conflict */
sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUNXI_GPIO_INPUT);
sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUNXI_GPIO_INPUT);
#endif
#if defined(CONFIG_MACH_SUN8I)
sunxi_gpio_set_cfgpin(SUNXI_GPF(2), SUN8I_GPF_UART0_TX);
sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUN8I_GPF_UART0_RX);
#else
sunxi_gpio_set_cfgpin(SUNXI_GPF(2), SUNXI_GPF_UART0_TX);
sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUNXI_GPF_UART0_RX);
#endif
sunxi_gpio_set_pull(SUNXI_GPF(4), 1);
#elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I))
sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUN4I_GPB_UART0);
sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUN4I_GPB_UART0);
sunxi_gpio_set_pull(SUNXI_GPB(23), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN5I)
sunxi_gpio_set_cfgpin(SUNXI_GPB(19), SUN5I_GPB_UART0);
sunxi_gpio_set_cfgpin(SUNXI_GPB(20), SUN5I_GPB_UART0);
sunxi_gpio_set_pull(SUNXI_GPB(20), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN6I)
sunxi_gpio_set_cfgpin(SUNXI_GPH(20), SUN6I_GPH_UART0);
sunxi_gpio_set_cfgpin(SUNXI_GPH(21), SUN6I_GPH_UART0);
sunxi_gpio_set_pull(SUNXI_GPH(21), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 1 && defined(CONFIG_MACH_SUN9I)
sunxi_gpio_set_cfgpin(SUNXI_GPH(12), SUN9I_GPH_UART0);
sunxi_gpio_set_cfgpin(SUNXI_GPH(13), SUN9I_GPH_UART0);
sunxi_gpio_set_pull(SUNXI_GPH(13), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 2 && defined(CONFIG_MACH_SUN5I)
sunxi_gpio_set_cfgpin(SUNXI_GPG(3), SUN5I_GPG_UART1);
sunxi_gpio_set_cfgpin(SUNXI_GPG(4), SUN5I_GPG_UART1);
sunxi_gpio_set_pull(SUNXI_GPG(4), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 3 && defined(CONFIG_MACH_SUN8I)
sunxi_gpio_set_cfgpin(SUNXI_GPB(0), SUN8I_GPB_UART2);
sunxi_gpio_set_cfgpin(SUNXI_GPB(1), SUN8I_GPB_UART2);
sunxi_gpio_set_pull(SUNXI_GPB(1), SUNXI_GPIO_PULL_UP);
#elif CONFIG_CONS_INDEX == 5 && defined(CONFIG_MACH_SUN8I)
sunxi_gpio_set_cfgpin(SUNXI_GPL(2), SUN8I_GPL_R_UART);
sunxi_gpio_set_cfgpin(SUNXI_GPL(3), SUN8I_GPL_R_UART);
sunxi_gpio_set_pull(SUNXI_GPL(3), SUNXI_GPIO_PULL_UP);
#else
#error Unsupported console port number. Please fix pin mux settings in board.c
#endif
return 0;
}
void spl_board_load_image(void)
{
debug("Returning to FEL sp=%x, lr=%x\n", fel_stash.sp, fel_stash.lr);
return_to_fel(fel_stash.sp, fel_stash.lr);
}
void s_init(void)
{
#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I_A23
/* Magic (undocmented) value taken from boot0, without this DRAM
* access gets messed up (seems cache related) */
setbits_le32(SUNXI_SRAMC_BASE + 0x44, 0x1800);
#endif
#if defined CONFIG_MACH_SUN6I || \
defined CONFIG_MACH_SUN7I || \
defined CONFIG_MACH_SUN8I
/* Enable SMP mode for CPU0, by setting bit 6 of Auxiliary Ctl reg */
asm volatile(
"mrc p15, 0, r0, c1, c0, 1\n"
"orr r0, r0, #1 << 6\n"
"mcr p15, 0, r0, c1, c0, 1\n");
#endif
clock_init();
timer_init();
gpio_init();
i2c_init_board();
}
#ifdef CONFIG_SPL_BUILD
/* The sunxi internal brom will try to loader external bootloader
* from mmc0, nand flash, mmc2.
*
* Unfortunately we can't check how SPL was loaded so assume it's
* always the first SD/MMC controller, unless it was explicitly
* stated that SPL is on nand flash.
*/
u32 spl_boot_device(void)
{
#if defined(CONFIG_SPL_NAND_SUPPORT)
/*
* This is compile time configuration informing SPL, that it
* was loaded from nand flash.
*/
return BOOT_DEVICE_NAND;
#else
/*
* When booting from the SD card, the "eGON.BT0" signature is expected
* to be found in memory at the address 0x0004 (see the "mksunxiboot"
* tool, which generates this header).
*
* When booting in the FEL mode over USB, this signature is patched in
* memory and replaced with something else by the 'fel' tool. This other
* signature is selected in such a way, that it can't be present in a
* valid bootable SD card image (because the BROM would refuse to
* execute the SPL in this case).
*
* This branch is just making a decision at runtime whether to load
* the main u-boot binary from the SD card (if the "eGON.BT0" signature
* is found) or return to the FEL code in the BROM to wait and receive
* the main u-boot binary over USB.
*/
if (readl(4) == 0x4E4F4765 && readl(8) == 0x3054422E) /* eGON.BT0 */
return BOOT_DEVICE_MMC1;
else
return BOOT_DEVICE_BOARD;
#endif
}
/* No confirmation data available in SPL yet. Hardcode bootmode */
u32 spl_boot_mode(void)
{
return MMCSD_MODE_RAW;
}
void board_init_f(ulong dummy)
{
preloader_console_init();
#ifdef CONFIG_SPL_I2C_SUPPORT
/* Needed early by sunxi_board_init if PMU is enabled */
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
#endif
sunxi_board_init();
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
board_init_r(NULL, 0);
}
#endif
void reset_cpu(ulong addr)
{
#ifdef CONFIG_SUNXI_GEN_SUN4I
static const struct sunxi_wdog *wdog =
&((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;
/* Set the watchdog for its shortest interval (.5s) and wait */
writel(WDT_MODE_RESET_EN | WDT_MODE_EN, &wdog->mode);
writel(WDT_CTRL_KEY | WDT_CTRL_RESTART, &wdog->ctl);
while (1) {
/* sun5i sometimes gets stuck without this */
writel(WDT_MODE_RESET_EN | WDT_MODE_EN, &wdog->mode);
}
#endif
#ifdef CONFIG_SUNXI_GEN_SUN6I
static const struct sunxi_wdog *wdog =
((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;
/* Set the watchdog for its shortest interval (.5s) and wait */
writel(WDT_CFG_RESET, &wdog->cfg);
writel(WDT_MODE_EN, &wdog->mode);
writel(WDT_CTRL_KEY | WDT_CTRL_RESTART, &wdog->ctl);
#endif
}
#ifndef CONFIG_SYS_DCACHE_OFF
void enable_caches(void)
{
/* Enable D-cache. I-cache is already enabled in start.S */
dcache_enable();
}
#endif
#ifdef CONFIG_CMD_NET
/*
* Initializes on-chip ethernet controllers.
* to override, implement board_eth_init()
*/
int cpu_eth_init(bd_t *bis)
{
__maybe_unused int rc;
#ifdef CONFIG_MACPWR
gpio_direction_output(CONFIG_MACPWR, 1);
mdelay(200);
#endif
#ifdef CONFIG_SUNXI_GMAC
rc = sunxi_gmac_initialize(bis);
if (rc < 0) {
printf("sunxi: failed to initialize gmac\n");
return rc;
}
#endif
return 0;
}
#endif
Reference in a new issue View git blame Copy permalink