mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-26 22:52:18 +00:00
6d82517836
Now that new SPI NOR layer uses stateless 4 byte opcodes by default, don't enable SPI_FLASH_BAR. For SPI controllers that cannot support 4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c, renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to not break functionality. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
77 lines
1.9 KiB
Text
77 lines
1.9 KiB
Text
CONFIG_ARM=y
|
|
CONFIG_ARCH_MX6=y
|
|
CONFIG_SYS_TEXT_BASE=0x17800000
|
|
CONFIG_SPL_GPIO_SUPPORT=y
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_MX6_DDRCAL=y
|
|
CONFIG_TARGET_DISPLAY5=y
|
|
CONFIG_SPL_MMC_SUPPORT=y
|
|
CONFIG_SPL_SERIAL_SUPPORT=y
|
|
CONFIG_SPL=y
|
|
CONFIG_SPL_SPI_FLASH_SUPPORT=y
|
|
CONFIG_SPL_SPI_SUPPORT=y
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_FIT=y
|
|
CONFIG_SPL_LOAD_FIT=y
|
|
CONFIG_OF_BOARD_SETUP=y
|
|
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,MX6Q"
|
|
CONFIG_SUPPORT_RAW_INITRD=y
|
|
CONFIG_MISC_INIT_R=y
|
|
CONFIG_BOUNCE_BUFFER=y
|
|
CONFIG_SPL_BOOTCOUNT_LIMIT=y
|
|
# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
|
|
CONFIG_SPL_DMA_SUPPORT=y
|
|
CONFIG_SPL_ENV_SUPPORT=y
|
|
CONFIG_SPL_SAVEENV=y
|
|
CONFIG_SPL_I2C_SUPPORT=y
|
|
CONFIG_SPL_OS_BOOT=y
|
|
CONFIG_SPL_SPI_LOAD=y
|
|
CONFIG_SPL_WATCHDOG_SUPPORT=y
|
|
CONFIG_HUSH_PARSER=y
|
|
CONFIG_SYS_PROMPT="display5 > "
|
|
CONFIG_CMD_BOOTZ=y
|
|
# CONFIG_CMD_ELF is not set
|
|
CONFIG_CMD_ASKENV=y
|
|
CONFIG_CRC32_VERIFY=y
|
|
CONFIG_CMD_EEPROM=y
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_GPT=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_PART=y
|
|
CONFIG_CMD_SF=y
|
|
CONFIG_CMD_SPI=y
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_CMD_MII=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_CMD_TIME=y
|
|
CONFIG_CMD_EXT2=y
|
|
CONFIG_CMD_EXT4=y
|
|
CONFIG_CMD_FAT=y
|
|
CONFIG_CMD_FS_GENERIC=y
|
|
CONFIG_CMD_MTDPARTS=y
|
|
CONFIG_MTDIDS_DEFAULT="nor0=02008000.spi.1"
|
|
CONFIG_MTDPARTS_DEFAULT="mtdparts=02008000.spi.1:128k(SPL),1m(u-boot),64k(env1),64k(env2),4m(swu-kernel),16m(swu-initramfs),1m(factory),-(reserved)"
|
|
# CONFIG_SPL_EFI_PARTITION is not set
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="imx6q-display5"
|
|
CONFIG_ENV_IS_IN_SPI_FLASH=y
|
|
CONFIG_BOOTCOUNT_LIMIT=y
|
|
CONFIG_BOOTCOUNT_BOOTLIMIT=3
|
|
CONFIG_SYS_BOOTCOUNT_SINGLEWORD=y
|
|
CONFIG_SYS_BOOTCOUNT_ADDR=0x020CC068
|
|
CONFIG_FSL_ESDHC=y
|
|
CONFIG_MTD_DEVICE=y
|
|
CONFIG_SPI_FLASH=y
|
|
CONFIG_SPI_FLASH_SPANSION=y
|
|
CONFIG_SPI_FLASH_STMICRO=y
|
|
CONFIG_PHYLIB=y
|
|
CONFIG_PHY_MARVELL=y
|
|
CONFIG_FEC_MXC=y
|
|
CONFIG_MII=y
|
|
CONFIG_MXC_UART=y
|
|
CONFIG_SPI=y
|
|
CONFIG_MXC_SPI=y
|
|
CONFIG_IMX_WATCHDOG=y
|