u-boot/drivers/mtd/nand/vf610_nfc.c
Stefan Agner 8fca2d8cb8 mtd: vf610_nfc: enable ONFI detection
This changes enable ONFI detection. The Read ID command now allows
one address byte which is needed for ONFI detection. To read the
ONFI parameter page, the NAND_CMD_PARAM need to be supported. The
CMD code enables one command and one address byte along with reading
data from flash using R/B#, as specified by ONFI.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-05-24 14:27:46 -05:00

745 lines
19 KiB
C

/*
* Copyright 2009-2014 Freescale Semiconductor, Inc. and others
*
* Description: MPC5125, VF610, MCF54418 and Kinetis K70 Nand driver.
* Ported to U-Boot by Stefan Agner
* Based on RFC driver posted on Kernel Mailing list by Bill Pringlemeir
* Jason ported to M54418TWR and MVFA5.
* Authors: Stefan Agner <stefan.agner@toradex.com>
* Bill Pringlemeir <bpringlemeir@nbsps.com>
* Shaohui Xie <b21989@freescale.com>
* Jason Jin <Jason.jin@freescale.com>
*
* Based on original driver mpc5121_nfc.c.
*
* This is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* Limitations:
* - Untested on MPC5125 and M54418.
* - DMA not used.
* - 2K pages or less.
* - Only 2K page w. 64+OOB and hardware ECC.
*/
#include <common.h>
#include <malloc.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <nand.h>
#include <errno.h>
#include <asm/io.h>
/* Register Offsets */
#define NFC_FLASH_CMD1 0x3F00
#define NFC_FLASH_CMD2 0x3F04
#define NFC_COL_ADDR 0x3F08
#define NFC_ROW_ADDR 0x3F0c
#define NFC_ROW_ADDR_INC 0x3F14
#define NFC_FLASH_STATUS1 0x3F18
#define NFC_FLASH_STATUS2 0x3F1c
#define NFC_CACHE_SWAP 0x3F28
#define NFC_SECTOR_SIZE 0x3F2c
#define NFC_FLASH_CONFIG 0x3F30
#define NFC_IRQ_STATUS 0x3F38
/* Addresses for NFC MAIN RAM BUFFER areas */
#define NFC_MAIN_AREA(n) ((n) * 0x1000)
#define PAGE_2K 0x0800
#define OOB_64 0x0040
/*
* NFC_CMD2[CODE] values. See section:
* - 31.4.7 Flash Command Code Description, Vybrid manual
* - 23.8.6 Flash Command Sequencer, MPC5125 manual
*
* Briefly these are bitmasks of controller cycles.
*/
#define READ_PAGE_CMD_CODE 0x7EE0
#define READ_ONFI_PARAM_CMD_CODE 0x4860
#define PROGRAM_PAGE_CMD_CODE 0x7FC0
#define ERASE_CMD_CODE 0x4EC0
#define READ_ID_CMD_CODE 0x4804
#define RESET_CMD_CODE 0x4040
#define STATUS_READ_CMD_CODE 0x4068
/* NFC ECC mode define */
#define ECC_BYPASS 0
#define ECC_45_BYTE 6
#define ECC_60_BYTE 7
/*** Register Mask and bit definitions */
/* NFC_FLASH_CMD1 Field */
#define CMD_BYTE2_MASK 0xFF000000
#define CMD_BYTE2_SHIFT 24
/* NFC_FLASH_CM2 Field */
#define CMD_BYTE1_MASK 0xFF000000
#define CMD_BYTE1_SHIFT 24
#define CMD_CODE_MASK 0x00FFFF00
#define CMD_CODE_SHIFT 8
#define BUFNO_MASK 0x00000006
#define BUFNO_SHIFT 1
#define START_BIT (1<<0)
/* NFC_COL_ADDR Field */
#define COL_ADDR_MASK 0x0000FFFF
#define COL_ADDR_SHIFT 0
/* NFC_ROW_ADDR Field */
#define ROW_ADDR_MASK 0x00FFFFFF
#define ROW_ADDR_SHIFT 0
#define ROW_ADDR_CHIP_SEL_RB_MASK 0xF0000000
#define ROW_ADDR_CHIP_SEL_RB_SHIFT 28
#define ROW_ADDR_CHIP_SEL_MASK 0x0F000000
#define ROW_ADDR_CHIP_SEL_SHIFT 24
/* NFC_FLASH_STATUS2 Field */
#define STATUS_BYTE1_MASK 0x000000FF
/* NFC_FLASH_CONFIG Field */
#define CONFIG_ECC_SRAM_ADDR_MASK 0x7FC00000
#define CONFIG_ECC_SRAM_ADDR_SHIFT 22
#define CONFIG_ECC_SRAM_REQ_BIT (1<<21)
#define CONFIG_DMA_REQ_BIT (1<<20)
#define CONFIG_ECC_MODE_MASK 0x000E0000
#define CONFIG_ECC_MODE_SHIFT 17
#define CONFIG_FAST_FLASH_BIT (1<<16)
#define CONFIG_16BIT (1<<7)
#define CONFIG_BOOT_MODE_BIT (1<<6)
#define CONFIG_ADDR_AUTO_INCR_BIT (1<<5)
#define CONFIG_BUFNO_AUTO_INCR_BIT (1<<4)
#define CONFIG_PAGE_CNT_MASK 0xF
#define CONFIG_PAGE_CNT_SHIFT 0
/* NFC_IRQ_STATUS Field */
#define IDLE_IRQ_BIT (1<<29)
#define IDLE_EN_BIT (1<<20)
#define CMD_DONE_CLEAR_BIT (1<<18)
#define IDLE_CLEAR_BIT (1<<17)
#define NFC_TIMEOUT (1000)
/* ECC status placed at end of buffers. */
#define ECC_SRAM_ADDR ((PAGE_2K+256-8) >> 3)
#define ECC_STATUS_MASK 0x80
#define ECC_ERR_COUNT 0x3F
/*
* ECC status is stored at NFC_CFG[ECCADD] +4 for little-endian
* and +7 for big-endian SOC.
*/
#ifdef CONFIG_VF610
#define ECC_OFFSET 4
#else
#define ECC_OFFSET 7
#endif
struct vf610_nfc {
struct mtd_info *mtd;
struct nand_chip chip;
void __iomem *regs;
uint column;
/* Status and ID are in alternate locations. */
int alt_buf;
#define ALT_BUF_ID 1
#define ALT_BUF_STAT 2
#define ALT_BUF_ONFI 3
struct clk *clk;
};
#define mtd_to_nfc(_mtd) \
(struct vf610_nfc *)((struct nand_chip *)_mtd->priv)->priv
#if defined(CONFIG_SYS_NAND_VF610_NFC_45_ECC_BYTES)
#define ECC_HW_MODE ECC_45_BYTE
static struct nand_ecclayout vf610_nfc_ecc = {
.eccbytes = 45,
.eccpos = {19, 20, 21, 22, 23,
24, 25, 26, 27, 28, 29, 30, 31,
32, 33, 34, 35, 36, 37, 38, 39,
40, 41, 42, 43, 44, 45, 46, 47,
48, 49, 50, 51, 52, 53, 54, 55,
56, 57, 58, 59, 60, 61, 62, 63},
.oobfree = {
{.offset = 8,
.length = 11} }
};
#elif defined(CONFIG_SYS_NAND_VF610_NFC_60_ECC_BYTES)
#define ECC_HW_MODE ECC_60_BYTE
static struct nand_ecclayout vf610_nfc_ecc = {
.eccbytes = 60,
.eccpos = { 4, 5, 6, 7, 8, 9, 10, 11,
12, 13, 14, 15, 16, 17, 18, 19,
20, 21, 22, 23, 24, 25, 26, 27,
28, 29, 30, 31, 32, 33, 34, 35,
36, 37, 38, 39, 40, 41, 42, 43,
44, 45, 46, 47, 48, 49, 50, 51,
52, 53, 54, 55, 56, 57, 58, 59,
60, 61, 62, 63 },
.oobfree = {
{.offset = 2,
.length = 2} }
};
#endif
static inline u32 vf610_nfc_read(struct mtd_info *mtd, uint reg)
{
struct vf610_nfc *nfc = mtd_to_nfc(mtd);
return readl(nfc->regs + reg);
}
static inline void vf610_nfc_write(struct mtd_info *mtd, uint reg, u32 val)
{
struct vf610_nfc *nfc = mtd_to_nfc(mtd);
writel(val, nfc->regs + reg);
}
static inline void vf610_nfc_set(struct mtd_info *mtd, uint reg, u32 bits)
{
vf610_nfc_write(mtd, reg, vf610_nfc_read(mtd, reg) | bits);
}
static inline void vf610_nfc_clear(struct mtd_info *mtd, uint reg, u32 bits)
{
vf610_nfc_write(mtd, reg, vf610_nfc_read(mtd, reg) & ~bits);
}
static inline void vf610_nfc_set_field(struct mtd_info *mtd, u32 reg,
u32 mask, u32 shift, u32 val)
{
vf610_nfc_write(mtd, reg,
(vf610_nfc_read(mtd, reg) & (~mask)) | val << shift);
}
static inline void vf610_nfc_memcpy(void *dst, const void *src, size_t n)
{
/*
* Use this accessor for the interal SRAM buffers. On ARM we can
* treat the SRAM buffer as if its memory, hence use memcpy
*/
memcpy(dst, src, n);
}
/* Clear flags for upcoming command */
static inline void vf610_nfc_clear_status(void __iomem *regbase)
{
void __iomem *reg = regbase + NFC_IRQ_STATUS;
u32 tmp = __raw_readl(reg);
tmp |= CMD_DONE_CLEAR_BIT | IDLE_CLEAR_BIT;
__raw_writel(tmp, reg);
}
/* Wait for complete operation */
static inline void vf610_nfc_done(struct mtd_info *mtd)
{
struct vf610_nfc *nfc = mtd_to_nfc(mtd);
uint start;
/*
* Barrier is needed after this write. This write need
* to be done before reading the next register the first
* time.
* vf610_nfc_set implicates such a barrier by using writel
* to write to the register.
*/
vf610_nfc_set(mtd, NFC_FLASH_CMD2, START_BIT);
start = get_timer(0);
while (!(vf610_nfc_read(mtd, NFC_IRQ_STATUS) & IDLE_IRQ_BIT)) {
if (get_timer(start) > NFC_TIMEOUT) {
printf("Timeout while waiting for !BUSY.\n");
return;
}
}
vf610_nfc_clear_status(nfc->regs);
}
static u8 vf610_nfc_get_id(struct mtd_info *mtd, int col)
{
u32 flash_id;
if (col < 4) {
flash_id = vf610_nfc_read(mtd, NFC_FLASH_STATUS1);
return (flash_id >> (3-col)*8) & 0xff;
} else {
flash_id = vf610_nfc_read(mtd, NFC_FLASH_STATUS2);
return flash_id >> 24;
}
}
static u8 vf610_nfc_get_status(struct mtd_info *mtd)
{
return vf610_nfc_read(mtd, NFC_FLASH_STATUS2) & STATUS_BYTE1_MASK;
}
/* Single command */
static void vf610_nfc_send_command(void __iomem *regbase, u32 cmd_byte1,
u32 cmd_code)
{
void __iomem *reg = regbase + NFC_FLASH_CMD2;
u32 tmp;
vf610_nfc_clear_status(regbase);
tmp = __raw_readl(reg);
tmp &= ~(CMD_BYTE1_MASK | CMD_CODE_MASK | BUFNO_MASK);
tmp |= cmd_byte1 << CMD_BYTE1_SHIFT;
tmp |= cmd_code << CMD_CODE_SHIFT;
__raw_writel(tmp, reg);
}
/* Two commands */
static void vf610_nfc_send_commands(void __iomem *regbase, u32 cmd_byte1,
u32 cmd_byte2, u32 cmd_code)
{
void __iomem *reg = regbase + NFC_FLASH_CMD1;
u32 tmp;
vf610_nfc_send_command(regbase, cmd_byte1, cmd_code);
tmp = __raw_readl(reg);
tmp &= ~CMD_BYTE2_MASK;
tmp |= cmd_byte2 << CMD_BYTE2_SHIFT;
__raw_writel(tmp, reg);
}
static void vf610_nfc_addr_cycle(struct mtd_info *mtd, int column, int page)
{
if (column != -1) {
struct vf610_nfc *nfc = mtd_to_nfc(mtd);
if (nfc->chip.options & NAND_BUSWIDTH_16)
column = column / 2;
vf610_nfc_set_field(mtd, NFC_COL_ADDR, COL_ADDR_MASK,
COL_ADDR_SHIFT, column);
}
if (page != -1)
vf610_nfc_set_field(mtd, NFC_ROW_ADDR, ROW_ADDR_MASK,
ROW_ADDR_SHIFT, page);
}
static inline void vf610_nfc_ecc_mode(struct mtd_info *mtd, int ecc_mode)
{
vf610_nfc_set_field(mtd, NFC_FLASH_CONFIG,
CONFIG_ECC_MODE_MASK,
CONFIG_ECC_MODE_SHIFT, ecc_mode);
}
static inline void vf610_nfc_transfer_size(void __iomem *regbase, int size)
{
__raw_writel(size, regbase + NFC_SECTOR_SIZE);
}
/* Send command to NAND chip */
static void vf610_nfc_command(struct mtd_info *mtd, unsigned command,
int column, int page)
{
struct vf610_nfc *nfc = mtd_to_nfc(mtd);
int page_sz = nfc->chip.options & NAND_BUSWIDTH_16 ? 1 : 0;
nfc->column = max(column, 0);
nfc->alt_buf = 0;
switch (command) {
case NAND_CMD_SEQIN:
/* Use valid column/page from preread... */
vf610_nfc_addr_cycle(mtd, column, page);
/*
* SEQIN => data => PAGEPROG sequence is done by the controller
* hence we do not need to issue the command here...
*/
return;
case NAND_CMD_PAGEPROG:
page_sz += mtd->writesize + mtd->oobsize;
vf610_nfc_transfer_size(nfc->regs, page_sz);
vf610_nfc_send_commands(nfc->regs, NAND_CMD_SEQIN,
command, PROGRAM_PAGE_CMD_CODE);
vf610_nfc_ecc_mode(mtd, ECC_HW_MODE);
break;
case NAND_CMD_RESET:
vf610_nfc_transfer_size(nfc->regs, 0);
vf610_nfc_send_command(nfc->regs, command, RESET_CMD_CODE);
break;
case NAND_CMD_READOOB:
page_sz += mtd->oobsize;
column = mtd->writesize;
vf610_nfc_transfer_size(nfc->regs, page_sz);
vf610_nfc_send_commands(nfc->regs, NAND_CMD_READ0,
NAND_CMD_READSTART, READ_PAGE_CMD_CODE);
vf610_nfc_addr_cycle(mtd, column, page);
vf610_nfc_ecc_mode(mtd, ECC_BYPASS);
break;
case NAND_CMD_READ0:
page_sz += mtd->writesize + mtd->oobsize;
column = 0;
vf610_nfc_transfer_size(nfc->regs, page_sz);
vf610_nfc_send_commands(nfc->regs, NAND_CMD_READ0,
NAND_CMD_READSTART, READ_PAGE_CMD_CODE);
vf610_nfc_addr_cycle(mtd, column, page);
vf610_nfc_ecc_mode(mtd, ECC_HW_MODE);
break;
case NAND_CMD_PARAM:
nfc->alt_buf = ALT_BUF_ONFI;
vf610_nfc_transfer_size(nfc->regs, 768);
vf610_nfc_send_command(nfc->regs, NAND_CMD_PARAM,
READ_ONFI_PARAM_CMD_CODE);
vf610_nfc_set_field(mtd, NFC_ROW_ADDR, ROW_ADDR_MASK,
ROW_ADDR_SHIFT, column);
vf610_nfc_ecc_mode(mtd, ECC_BYPASS);
break;
case NAND_CMD_ERASE1:
vf610_nfc_transfer_size(nfc->regs, 0);
vf610_nfc_send_commands(nfc->regs, command,
NAND_CMD_ERASE2, ERASE_CMD_CODE);
vf610_nfc_addr_cycle(mtd, column, page);
break;
case NAND_CMD_READID:
nfc->alt_buf = ALT_BUF_ID;
nfc->column = 0;
vf610_nfc_transfer_size(nfc->regs, 0);
vf610_nfc_send_command(nfc->regs, command, READ_ID_CMD_CODE);
vf610_nfc_set_field(mtd, NFC_ROW_ADDR, ROW_ADDR_MASK,
ROW_ADDR_SHIFT, column);
break;
case NAND_CMD_STATUS:
nfc->alt_buf = ALT_BUF_STAT;
vf610_nfc_transfer_size(nfc->regs, 0);
vf610_nfc_send_command(nfc->regs, command,
STATUS_READ_CMD_CODE);
break;
default:
return;
}
vf610_nfc_done(mtd);
}
/* Read data from NFC buffers */
static void vf610_nfc_read_buf(struct mtd_info *mtd, u_char *buf, int len)
{
struct vf610_nfc *nfc = mtd_to_nfc(mtd);
uint c = nfc->column;
/* Alternate buffers are only supported through read_byte */
if (nfc->alt_buf)
return;
vf610_nfc_memcpy(buf, nfc->regs + NFC_MAIN_AREA(0) + c, len);
nfc->column += len;
}
/* Write data to NFC buffers */
static void vf610_nfc_write_buf(struct mtd_info *mtd, const u_char *buf,
int len)
{
struct vf610_nfc *nfc = mtd_to_nfc(mtd);
uint c = nfc->column;
uint l;
l = min((uint)len, mtd->writesize + mtd->oobsize - c);
nfc->column += l;
vf610_nfc_memcpy(nfc->regs + NFC_MAIN_AREA(0) + c, buf, l);
}
/* Read byte from NFC buffers */
static u8 vf610_nfc_read_byte(struct mtd_info *mtd)
{
struct vf610_nfc *nfc = mtd_to_nfc(mtd);
u8 tmp;
uint c = nfc->column;
switch (nfc->alt_buf) {
case ALT_BUF_ID:
tmp = vf610_nfc_get_id(mtd, c);
break;
case ALT_BUF_STAT:
tmp = vf610_nfc_get_status(mtd);
break;
case ALT_BUF_ONFI:
#ifdef __LITTLE_ENDIAN
/* Reverse byte since the controller uses big endianness */
c = nfc->column ^ 0x3;
tmp = *((u8 *)(nfc->regs + NFC_MAIN_AREA(0) + c));
break;
#endif
default:
tmp = *((u8 *)(nfc->regs + NFC_MAIN_AREA(0) + c));
break;
}
nfc->column++;
return tmp;
}
/* Read word from NFC buffers */
static u16 vf610_nfc_read_word(struct mtd_info *mtd)
{
u16 tmp;
vf610_nfc_read_buf(mtd, (u_char *)&tmp, sizeof(tmp));
return tmp;
}
/* If not provided, upper layers apply a fixed delay. */
static int vf610_nfc_dev_ready(struct mtd_info *mtd)
{
/* NFC handles R/B internally; always ready. */
return 1;
}
/*
* This function supports Vybrid only (MPC5125 would have full RB and four CS)
*/
static void vf610_nfc_select_chip(struct mtd_info *mtd, int chip)
{
#ifdef CONFIG_VF610
u32 tmp = vf610_nfc_read(mtd, NFC_ROW_ADDR);
tmp &= ~(ROW_ADDR_CHIP_SEL_RB_MASK | ROW_ADDR_CHIP_SEL_MASK);
tmp |= 1 << ROW_ADDR_CHIP_SEL_RB_SHIFT;
if (chip == 0)
tmp |= 1 << ROW_ADDR_CHIP_SEL_SHIFT;
else if (chip == 1)
tmp |= 2 << ROW_ADDR_CHIP_SEL_SHIFT;
vf610_nfc_write(mtd, NFC_ROW_ADDR, tmp);
#endif
}
/* Count the number of 0's in buff upto max_bits */
static inline int count_written_bits(uint8_t *buff, int size, int max_bits)
{
uint32_t *buff32 = (uint32_t *)buff;
int k, written_bits = 0;
for (k = 0; k < (size / 4); k++) {
written_bits += hweight32(~buff32[k]);
if (written_bits > max_bits)
break;
}
return written_bits;
}
static inline int vf610_nfc_correct_data(struct mtd_info *mtd, u_char *dat)
{
struct vf610_nfc *nfc = mtd_to_nfc(mtd);
u8 ecc_status;
u8 ecc_count;
int flip;
ecc_status = __raw_readb(nfc->regs + ECC_SRAM_ADDR * 8 + ECC_OFFSET);
ecc_count = ecc_status & ECC_ERR_COUNT;
if (!(ecc_status & ECC_STATUS_MASK))
return ecc_count;
/* If 'ecc_count' zero or less then buffer is all 0xff or erased. */
flip = count_written_bits(dat, nfc->chip.ecc.size, ecc_count);
/* ECC failed. */
if (flip > ecc_count && flip > (nfc->chip.ecc.strength / 2))
return -1;
/* Erased page. */
memset(dat, 0xff, nfc->chip.ecc.size);
return 0;
}
static int vf610_nfc_read_page(struct mtd_info *mtd, struct nand_chip *chip,
uint8_t *buf, int oob_required, int page)
{
int eccsize = chip->ecc.size;
int stat;
uint8_t *p = buf;
vf610_nfc_read_buf(mtd, p, eccsize);
if (oob_required)
vf610_nfc_read_buf(mtd, chip->oob_poi, mtd->oobsize);
stat = vf610_nfc_correct_data(mtd, p);
if (stat < 0)
mtd->ecc_stats.failed++;
else
mtd->ecc_stats.corrected += stat;
return 0;
}
/*
* ECC will be calculated automatically
*/
static int vf610_nfc_write_page(struct mtd_info *mtd, struct nand_chip *chip,
const uint8_t *buf, int oob_required)
{
vf610_nfc_write_buf(mtd, buf, mtd->writesize);
if (oob_required)
vf610_nfc_write_buf(mtd, chip->oob_poi, mtd->oobsize);
return 0;
}
struct vf610_nfc_config {
int hardware_ecc;
int width;
int flash_bbt;
};
static int vf610_nfc_nand_init(int devnum, void __iomem *addr)
{
struct mtd_info *mtd = &nand_info[devnum];
struct nand_chip *chip;
struct vf610_nfc *nfc;
int err = 0;
struct vf610_nfc_config cfg = {
.hardware_ecc = 1,
#ifdef CONFIG_SYS_NAND_BUSWIDTH_16BIT
.width = 16,
#else
.width = 8,
#endif
.flash_bbt = 1,
};
nfc = malloc(sizeof(*nfc));
if (!nfc) {
printf(KERN_ERR "%s: Memory exhausted!\n", __func__);
return -ENOMEM;
}
chip = &nfc->chip;
nfc->regs = addr;
mtd->priv = chip;
chip->priv = nfc;
if (cfg.width == 16)
chip->options |= NAND_BUSWIDTH_16;
/* Use 8-bit mode during initialization */
vf610_nfc_clear(mtd, NFC_FLASH_CONFIG, CONFIG_16BIT);
/* Disable subpage writes as we do not provide ecc->hwctl */
chip->options |= NAND_NO_SUBPAGE_WRITE;
chip->dev_ready = vf610_nfc_dev_ready;
chip->cmdfunc = vf610_nfc_command;
chip->read_byte = vf610_nfc_read_byte;
chip->read_word = vf610_nfc_read_word;
chip->read_buf = vf610_nfc_read_buf;
chip->write_buf = vf610_nfc_write_buf;
chip->select_chip = vf610_nfc_select_chip;
/* Bad block options. */
if (cfg.flash_bbt)
chip->bbt_options = NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB |
NAND_BBT_CREATE;
/* Set configuration register. */
vf610_nfc_clear(mtd, NFC_FLASH_CONFIG, CONFIG_ADDR_AUTO_INCR_BIT);
vf610_nfc_clear(mtd, NFC_FLASH_CONFIG, CONFIG_BUFNO_AUTO_INCR_BIT);
vf610_nfc_clear(mtd, NFC_FLASH_CONFIG, CONFIG_BOOT_MODE_BIT);
vf610_nfc_clear(mtd, NFC_FLASH_CONFIG, CONFIG_DMA_REQ_BIT);
vf610_nfc_set(mtd, NFC_FLASH_CONFIG, CONFIG_FAST_FLASH_BIT);
/* Enable Idle IRQ */
vf610_nfc_set(mtd, NFC_IRQ_STATUS, IDLE_EN_BIT);
/* PAGE_CNT = 1 */
vf610_nfc_set_field(mtd, NFC_FLASH_CONFIG, CONFIG_PAGE_CNT_MASK,
CONFIG_PAGE_CNT_SHIFT, 1);
/* Set ECC_STATUS offset */
vf610_nfc_set_field(mtd, NFC_FLASH_CONFIG,
CONFIG_ECC_SRAM_ADDR_MASK,
CONFIG_ECC_SRAM_ADDR_SHIFT, ECC_SRAM_ADDR);
/* first scan to find the device and get the page size */
if (nand_scan_ident(mtd, CONFIG_SYS_MAX_NAND_DEVICE, NULL)) {
err = -ENXIO;
goto error;
}
if (cfg.width == 16)
vf610_nfc_set(mtd, NFC_FLASH_CONFIG, CONFIG_16BIT);
chip->ecc.mode = NAND_ECC_SOFT; /* default */
/* Single buffer only, max 256 OOB minus ECC status */
if (mtd->writesize + mtd->oobsize > PAGE_2K + 256 - 8) {
dev_err(nfc->dev, "Unsupported flash size\n");
err = -ENXIO;
goto error;
}
if (cfg.hardware_ecc) {
if (mtd->writesize != PAGE_2K && mtd->oobsize < 64) {
dev_err(nfc->dev, "Unsupported flash with hwecc\n");
err = -ENXIO;
goto error;
}
/* Current HW ECC layouts only use 64 bytes of OOB */
if (mtd->oobsize > 64)
mtd->oobsize = 64;
/* propagate ecc.layout to mtd_info */
mtd->ecclayout = chip->ecc.layout;
chip->ecc.read_page = vf610_nfc_read_page;
chip->ecc.write_page = vf610_nfc_write_page;
chip->ecc.mode = NAND_ECC_HW;
chip->ecc.size = PAGE_2K;
chip->ecc.layout = &vf610_nfc_ecc;
#if defined(CONFIG_SYS_NAND_VF610_NFC_45_ECC_BYTES)
chip->ecc.strength = 24;
chip->ecc.bytes = 45;
#elif defined(CONFIG_SYS_NAND_VF610_NFC_60_ECC_BYTES)
chip->ecc.strength = 32;
chip->ecc.bytes = 60;
#endif
/* Enable ECC_STATUS */
vf610_nfc_set(mtd, NFC_FLASH_CONFIG, CONFIG_ECC_SRAM_REQ_BIT);
}
/* second phase scan */
err = nand_scan_tail(mtd);
if (err)
return err;
err = nand_register(devnum);
if (err)
return err;
return 0;
error:
return err;
}
void board_nand_init(void)
{
int err = vf610_nfc_nand_init(0, (void __iomem *)CONFIG_SYS_NAND_BASE);
if (err)
printf("VF610 NAND init failed (err %d)\n", err);
}