u-boot/board/freescale/mx6qsabreauto/mx6qsabreauto.c
Wolfgang Denk 1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00

303 lines
7.5 KiB
C

/*
* Copyright (C) 2012 Freescale Semiconductor, Inc.
*
* Author: Fabio Estevam <fabio.estevam@freescale.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6q_pins.h>
#include <asm/errno.h>
#include <asm/gpio.h>
#include <asm/imx-common/iomux-v3.h>
#include <asm/imx-common/mxc_i2c.h>
#include <asm/imx-common/boot_mode.h>
#include <mmc.h>
#include <fsl_esdhc.h>
#include <miiphy.h>
#include <netdev.h>
#include <asm/arch/sys_proto.h>
#include <i2c.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
PAD_CTL_ODE | PAD_CTL_SRE_FAST)
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
int dram_init(void)
{
gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
return 0;
}
iomux_v3_cfg_t const uart4_pads[] = {
MX6_PAD_KEY_COL0__UART4_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_KEY_ROW0__UART4_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
};
iomux_v3_cfg_t const enet_pads[] = {
MX6_PAD_KEY_COL1__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_KEY_COL2__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TXC__ENET_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TD0__ENET_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TD1__ENET_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TD2__ENET_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TD3__ENET_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_RXC__ENET_RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_RD0__ENET_RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_RD1__ENET_RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_RD2__ENET_RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_RD3__ENET_RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
};
/* I2C2 PMIC, iPod, Tuner, Codec, Touch, HDMI EDID, MIPI CSI2 card */
struct i2c_pads_info i2c_pad_info1 = {
.scl = {
.i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | PC,
.gpio_mode = MX6_PAD_EIM_EB2__GPIO_2_30 | PC,
.gp = IMX_GPIO_NR(2, 30)
},
.sda = {
.i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC,
.gpio_mode = MX6_PAD_KEY_ROW3__GPIO_4_13 | PC,
.gp = IMX_GPIO_NR(4, 13)
}
};
/*
* I2C3 MLB, Port Expanders (A, B, C), Video ADC, Light Sensor,
* Compass Sensor, Accelerometer, Res Touch
*/
struct i2c_pads_info i2c_pad_info2 = {
.scl = {
.i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | PC,
.gpio_mode = MX6_PAD_GPIO_3__GPIO_1_3 | PC,
.gp = IMX_GPIO_NR(1, 3)
},
.sda = {
.i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC,
.gpio_mode = MX6_PAD_EIM_D18__GPIO_3_18 | PC,
.gp = IMX_GPIO_NR(3, 18)
}
};
iomux_v3_cfg_t const i2c3_pads[] = {
MX6_PAD_EIM_A24__GPIO_5_4 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
iomux_v3_cfg_t const port_exp[] = {
MX6_PAD_SD2_DAT0__GPIO_1_15 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static void setup_iomux_enet(void)
{
imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
}
iomux_v3_cfg_t const usdhc3_pads[] = {
MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT4__USDHC3_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT5__USDHC3_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT6__USDHC3_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT7__USDHC3_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_GPIO_18__USDHC3_VSELECT | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_NANDF_CS2__GPIO_6_15 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
}
#ifdef CONFIG_FSL_ESDHC
struct fsl_esdhc_cfg usdhc_cfg[1] = {
{USDHC3_BASE_ADDR},
};
int board_mmc_getcd(struct mmc *mmc)
{
gpio_direction_input(IMX_GPIO_NR(6, 15));
return !gpio_get_value(IMX_GPIO_NR(6, 15));
}
int board_mmc_init(bd_t *bis)
{
imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
}
#endif
int mx6_rgmii_rework(struct phy_device *phydev)
{
unsigned short val;
/* To enable AR8031 ouput a 125MHz clk from CLK_25M */
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
val &= 0xffe3;
val |= 0x18;
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
/* introduce tx clock delay */
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
val |= 0x0100;
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
return 0;
}
int board_phy_config(struct phy_device *phydev)
{
mx6_rgmii_rework(phydev);
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
int board_eth_init(bd_t *bis)
{
int ret;
setup_iomux_enet();
ret = cpu_eth_init(bis);
if (ret)
printf("FEC MXC: %s:failed\n", __func__);
return 0;
}
#define BOARD_REV_B 0x200
#define BOARD_REV_A 0x100
static int mx6sabre_rev(void)
{
/*
* Get Board ID information from OCOTP_GP1[15:8]
* i.MX6Q ARD RevA: 0x01
* i.MX6Q ARD RevB: 0x02
*/
struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
struct fuse_bank *bank = &ocotp->bank[4];
struct fuse_bank4_regs *fuse =
(struct fuse_bank4_regs *)bank->fuse_regs;
int reg = readl(&fuse->gp1);
int ret;
switch (reg >> 8 & 0x0F) {
case 0x02:
ret = BOARD_REV_B;
break;
case 0x01:
default:
ret = BOARD_REV_A;
break;
}
return ret;
}
u32 get_board_rev(void)
{
int rev = mx6sabre_rev();
return (get_cpu_rev() & ~(0xF << 8)) | rev;
}
int board_early_init_f(void)
{
setup_iomux_uart();
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
/* I2C 2 and 3 setup - I2C 3 hw mux with EIM */
setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
/* I2C 3 Steer */
gpio_direction_output(IMX_GPIO_NR(5, 4), 1);
imx_iomux_v3_setup_multiple_pads(i2c3_pads, ARRAY_SIZE(i2c3_pads));
setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
gpio_direction_output(IMX_GPIO_NR(1, 15), 1);
imx_iomux_v3_setup_multiple_pads(port_exp, ARRAY_SIZE(port_exp));
return 0;
}
#ifdef CONFIG_CMD_BMODE
static const struct boot_mode board_boot_modes[] = {
/* 4 bit bus width */
{"mmc0", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
{NULL, 0},
};
#endif
int board_late_init(void)
{
#ifdef CONFIG_CMD_BMODE
add_board_boot_modes(board_boot_modes);
#endif
return 0;
}
int checkboard(void)
{
int rev = mx6sabre_rev();
char *revname;
switch (rev) {
case BOARD_REV_B:
revname = "B";
break;
case BOARD_REV_A:
default:
revname = "A";
break;
}
printf("Board: MX6Q-Sabreauto rev%s\n", revname);
return 0;
}