u-boot/board/freescale/ls1012ardb/eth.c
Chaitanya Sakinam cb1de6067a armv8: ls1012a: RGMII ports require internal delay
The correct setting for the RGMII ports on LS1012ARDB is to
enable delay on both Rx and Tx so the interface mode used should
be PHY_INTERFACE_MODE_RGMII_ID

Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27 14:16:28 +05:30

171 lines
4 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2015-2016 Freescale Semiconductor, Inc.
* Copyright 2017 NXP
*/
#include <common.h>
#include <dm.h>
#include <net.h>
#include <asm/io.h>
#include <netdev.h>
#include <fm_eth.h>
#include <fsl_mdio.h>
#include <malloc.h>
#include <asm/types.h>
#include <fsl_dtsec.h>
#include <asm/arch/soc.h>
#include <asm/arch-fsl-layerscape/config.h>
#include <asm/arch-fsl-layerscape/immap_lsch2.h>
#include <asm/arch/fsl_serdes.h>
#include <linux/delay.h>
#include <net/pfe_eth/pfe_eth.h>
#include <dm/platform_data/pfe_dm_eth.h>
#include <i2c.h>
#define DEFAULT_PFE_MDIO_NAME "PFE_MDIO"
static inline void ls1012ardb_reset_phy(void)
{
#ifdef CONFIG_TARGET_LS1012ARDB
/* Through reset IO expander reset both RGMII and SGMII PHYs */
#ifdef CONFIG_DM_I2C
struct udevice *dev;
int ret;
/*
* The I2C IO-expander PCAL9555A is mouted on I2C1 bus(bus number is 0).
*/
ret = i2c_get_chip_for_busnum(0, I2C_MUX_IO2_ADDR,
1, &dev);
if (ret) {
printf("%s: Cannot find udev for a bus %d\n", __func__,
0);
return;
}
/* Config port 0
* - config pin IOXP_RST_ETH1_B and IOXP_RST_ETH2_B
* are enabled as an output.
*/
dm_i2c_reg_write(dev, 6, __PHY_MASK);
/*
* Set port 0 output a value to reset ETH2 interface
* - pin IOXP_RST_ETH2_B output 0b0
*/
dm_i2c_reg_write(dev, 2, __PHY_ETH2_MASK);
mdelay(10);
dm_i2c_reg_write(dev, 2, __PHY_ETH1_MASK);
/*
* Set port 0 output a value to reset ETH1 interface
* - pin IOXP_RST_ETH1_B output 0b0
*/
mdelay(10);
dm_i2c_reg_write(dev, 2, 0xFF);
#else
i2c_reg_write(I2C_MUX_IO2_ADDR, 6, __PHY_MASK);
i2c_reg_write(I2C_MUX_IO2_ADDR, 2, __PHY_ETH2_MASK);
mdelay(10);
i2c_reg_write(I2C_MUX_IO2_ADDR, 2, __PHY_ETH1_MASK);
mdelay(10);
i2c_reg_write(I2C_MUX_IO2_ADDR, 2, 0xFF);
#endif
mdelay(50);
#endif
}
int pfe_eth_board_init(struct udevice *dev)
{
static int init_done;
struct mii_dev *bus;
struct pfe_mdio_info mac_mdio_info;
struct pfe_eth_dev *priv = dev_get_priv(dev);
struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
int srds_s1 = in_be32(&gur->rcwsr[4]) &
FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
srds_s1 >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
if (!init_done) {
ls1012ardb_reset_phy();
mac_mdio_info.reg_base = (void *)EMAC1_BASE_ADDR;
mac_mdio_info.name = DEFAULT_PFE_MDIO_NAME;
bus = pfe_mdio_init(&mac_mdio_info);
if (!bus) {
printf("Failed to register mdio\n");
return -1;
}
init_done = 1;
}
pfe_set_mdio(priv->gemac_port,
miiphy_get_dev_by_name(DEFAULT_PFE_MDIO_NAME));
switch (srds_s1) {
case 0x3508:
if (!priv->gemac_port) {
/* MAC1 */
pfe_set_phy_address_mode(priv->gemac_port,
CONFIG_PFE_EMAC1_PHY_ADDR,
PHY_INTERFACE_MODE_SGMII);
} else {
/* MAC2 */
pfe_set_phy_address_mode(priv->gemac_port,
CONFIG_PFE_EMAC2_PHY_ADDR,
PHY_INTERFACE_MODE_RGMII_ID);
}
break;
case 0x2208:
if (!priv->gemac_port) {
/* MAC1 */
pfe_set_phy_address_mode(priv->gemac_port,
CONFIG_PFE_EMAC1_PHY_ADDR,
PHY_INTERFACE_MODE_SGMII_2500);
} else {
/* MAC2 */
pfe_set_phy_address_mode(priv->gemac_port,
CONFIG_PFE_EMAC2_PHY_ADDR,
PHY_INTERFACE_MODE_SGMII_2500);
}
break;
default:
printf("unsupported SerDes PRCTL= %d\n", srds_s1);
break;
}
return 0;
}
static struct pfe_eth_pdata pfe_pdata0 = {
.pfe_eth_pdata_mac = {
.iobase = (phys_addr_t)EMAC1_BASE_ADDR,
.phy_interface = 0,
},
.pfe_ddr_addr = {
.ddr_pfe_baseaddr = (void *)CONFIG_DDR_PFE_BASEADDR,
.ddr_pfe_phys_baseaddr = CONFIG_DDR_PFE_PHYS_BASEADDR,
},
};
static struct pfe_eth_pdata pfe_pdata1 = {
.pfe_eth_pdata_mac = {
.iobase = (phys_addr_t)EMAC2_BASE_ADDR,
.phy_interface = 1,
},
.pfe_ddr_addr = {
.ddr_pfe_baseaddr = (void *)CONFIG_DDR_PFE_BASEADDR,
.ddr_pfe_phys_baseaddr = CONFIG_DDR_PFE_PHYS_BASEADDR,
},
};
U_BOOT_DEVICE(ls1012a_pfe0) = {
.name = "pfe_eth",
.platdata = &pfe_pdata0,
};
U_BOOT_DEVICE(ls1012a_pfe1) = {
.name = "pfe_eth",
.platdata = &pfe_pdata1,
};