Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-12 07:57:21 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/board/tqc/tqma6/tqma6.c
Markus Niebel cb07d74e2e Add TQ Systems TQMa6 board support 
This patch adds the changes to boards.cfg and the board directory
under board/tqc.

TQMa6 is a family of modules based on Freescale i.MX6. It consists of
TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3
TQMa6S (i.MX6 Solo)  featuring eMMC and 512 MiB DDR3

The modules need a baseboard. Initially the MBa6x starterkit mainboard is
supported. To easy support for other mainboards the functionality is splitted
in one file for the module (tqma6.c) and one file for the baseboard (tqma6_
mba6).

The modules can be boot from eMMC (on USDHC3) and SPI flash.

The following features are supported:
- MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard)
- Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module.
  The phy needs special configurations for the pad skew registers to adjust for
  the signal routing.
  Also support for standard ethernet commands and uppdate via tftp.
- SPI: ECSPI1 with bootable serial flash on module and two additional
  chip selects on MBa6x
- I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3)
  and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x
  are also configured.
- USB: high speed host 1 on MBa6x and support for USB storage
- PMIC: support for pfuze 100 on TQMa6<x>

Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2014-07-23 12:31:42 +02:00

262 lines
6.4 KiB
C
Raw Blame History

/*
* Copyright (C) 2012 Freescale Semiconductor, Inc.
* Author: Fabio Estevam <fabio.estevam@freescale.com>
*
* Copyright (C) 2013, 2014 TQ Systems (ported SabreSD to TQMa6x)
* Author: Markus Niebel <markus.niebel@tq-group.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <asm/arch/clock.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/sys_proto.h>
#include <asm/errno.h>
#include <asm/gpio.h>
#include <asm/io.h>
#include <asm/imx-common/mxc_i2c.h>
#include <common.h>
#include <fsl_esdhc.h>
#include <libfdt.h>
#include <i2c.h>
#include <mmc.h>
#include <power/pfuze100_pmic.h>
#include <power/pmic.h>
#include "tqma6_bb.h"
DECLARE_GLOBAL_DATA_PTR;
#define USDHC_CLK_PAD_CTRL (PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define GPIO_OUT_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_LOW | \
PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
#define GPIO_IN_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_LOW | \
PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
#define SPI_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
PAD_CTL_ODE | PAD_CTL_SRE_FAST)
int dram_init(void)
{
gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
return 0;
}
static const uint16_t tqma6_emmc_dsr = 0x0100;
/* eMMC on USDHCI3 always present */
static iomux_v3_cfg_t const tqma6_usdhc3_pads[] = {
NEW_PAD_CTRL(MX6_PAD_SD3_CLK__SD3_CLK, USDHC_PAD_CTRL),
NEW_PAD_CTRL(MX6_PAD_SD3_CMD__SD3_CMD, USDHC_PAD_CTRL),
NEW_PAD_CTRL(MX6_PAD_SD3_DAT0__SD3_DATA0, USDHC_PAD_CTRL),
NEW_PAD_CTRL(MX6_PAD_SD3_DAT1__SD3_DATA1, USDHC_PAD_CTRL),
NEW_PAD_CTRL(MX6_PAD_SD3_DAT2__SD3_DATA2, USDHC_PAD_CTRL),
NEW_PAD_CTRL(MX6_PAD_SD3_DAT3__SD3_DATA3, USDHC_PAD_CTRL),
NEW_PAD_CTRL(MX6_PAD_SD3_DAT4__SD3_DATA4, USDHC_PAD_CTRL),
NEW_PAD_CTRL(MX6_PAD_SD3_DAT5__SD3_DATA5, USDHC_PAD_CTRL),
NEW_PAD_CTRL(MX6_PAD_SD3_DAT6__SD3_DATA6, USDHC_PAD_CTRL),
NEW_PAD_CTRL(MX6_PAD_SD3_DAT7__SD3_DATA7, USDHC_PAD_CTRL),
/* eMMC reset */
NEW_PAD_CTRL(MX6_PAD_SD3_RST__SD3_RESET, GPIO_OUT_PAD_CTRL),
};
/*
* According to board_mmc_init() the following map is done:
* (U-boot device node) (Physical Port)
* mmc0 eMMC (SD3) on TQMa6
* mmc1 .. n optional slots used on baseboard
*/
struct fsl_esdhc_cfg tqma6_usdhc_cfg = {
.esdhc_base = USDHC3_BASE_ADDR,
.max_bus_width = 8,
};
int board_mmc_getcd(struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
int ret = 0;
if (cfg->esdhc_base == USDHC3_BASE_ADDR)
/* eMMC/uSDHC3 is always present */
ret = 1;
else
ret = tqma6_bb_board_mmc_getcd(mmc);
return ret;
}
int board_mmc_getwp(struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
int ret = 0;
if (cfg->esdhc_base == USDHC3_BASE_ADDR)
/* eMMC/uSDHC3 is always present */
ret = 0;
else
ret = tqma6_bb_board_mmc_getwp(mmc);
return ret;
}
int board_mmc_init(bd_t *bis)
{
imx_iomux_v3_setup_multiple_pads(tqma6_usdhc3_pads,
ARRAY_SIZE(tqma6_usdhc3_pads));
tqma6_usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
if (fsl_esdhc_initialize(bis, &tqma6_usdhc_cfg)) {
puts("Warning: failed to initialize eMMC dev\n");
} else {
struct mmc *mmc = find_mmc_device(0);
if (mmc)
mmc_set_dsr(mmc, tqma6_emmc_dsr);
}
tqma6_bb_board_mmc_init(bis);
return 0;
}
static iomux_v3_cfg_t const tqma6_ecspi1_pads[] = {
/* SS1 */
NEW_PAD_CTRL(MX6_PAD_EIM_D19__GPIO3_IO19, SPI_PAD_CTRL),
NEW_PAD_CTRL(MX6_PAD_EIM_D16__ECSPI1_SCLK, SPI_PAD_CTRL),
NEW_PAD_CTRL(MX6_PAD_EIM_D17__ECSPI1_MISO, SPI_PAD_CTRL),
NEW_PAD_CTRL(MX6_PAD_EIM_D18__ECSPI1_MOSI, SPI_PAD_CTRL),
};
static unsigned const tqma6_ecspi1_cs[] = {
IMX_GPIO_NR(3, 19),
};
static void tqma6_iomuxc_spi(void)
{
unsigned i;
for (i = 0; i < ARRAY_SIZE(tqma6_ecspi1_cs); ++i)
gpio_direction_output(tqma6_ecspi1_cs[i], 1);
imx_iomux_v3_setup_multiple_pads(tqma6_ecspi1_pads,
ARRAY_SIZE(tqma6_ecspi1_pads));
}
static struct i2c_pads_info tqma6_i2c3_pads = {
/* I2C3: on board LM75, M24C64, */
.scl = {
.i2c_mode = NEW_PAD_CTRL(MX6_PAD_GPIO_5__I2C3_SCL,
I2C_PAD_CTRL),
.gpio_mode = NEW_PAD_CTRL(MX6_PAD_GPIO_5__GPIO1_IO05,
I2C_PAD_CTRL),
.gp = IMX_GPIO_NR(1, 5)
},
.sda = {
.i2c_mode = NEW_PAD_CTRL(MX6_PAD_GPIO_6__I2C3_SDA,
I2C_PAD_CTRL),
.gpio_mode = NEW_PAD_CTRL(MX6_PAD_GPIO_6__GPIO1_IO06,
I2C_PAD_CTRL),
.gp = IMX_GPIO_NR(1, 6)
}
};
static void tqma6_setup_i2c(void)
{
/* use logical index for bus, e.g. I2C1 -> 0 */
setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &tqma6_i2c3_pads);
}
int board_early_init_f(void)
{
return tqma6_bb_board_early_init_f();
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
tqma6_iomuxc_spi();
tqma6_setup_i2c();
tqma6_bb_board_init();
return 0;
}
static const char *tqma6_get_boardname(void)
{
u32 cpurev = get_cpu_rev();
switch ((cpurev & 0xFF000) >> 12) {
case MXC_CPU_MX6SOLO:
return "TQMa6S";
break;
case MXC_CPU_MX6DL:
return "TQMa6DL";
break;
case MXC_CPU_MX6D:
return "TQMa6D";
break;
case MXC_CPU_MX6Q:
return "TQMa6Q";
break;
default:
return "??";
};
}
int board_late_init(void)
{
struct pmic *p;
u32 reg;
setenv("board_name", tqma6_get_boardname());
/*
* configure PFUZE100 PMIC:
* TODO: should go to power_init_board if bus switching is
* fixed in generic power code
*/
power_pfuze100_init(TQMA6_PFUZE100_I2C_BUS);
p = pmic_get("PFUZE100_PMIC");
if (p && !pmic_probe(p)) {
pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
printf("PMIC: PFUZE100_PMIC ID=0x%02x\n", reg);
}
tqma6_bb_board_late_init();
return 0;
}
int checkboard(void)
{
printf("Board: %s on a %s\n", tqma6_get_boardname(),
tqma6_bb_get_boardname());
return 0;
}
/*
* Device Tree Support
*/
#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
void ft_board_setup(void *blob, bd_t *bd)
{
/* bring in eMMC dsr settings */
do_fixup_by_path_u32(blob,
"/soc/aips-bus@02100000/usdhc@02198000",
"dsr", tqma6_emmc_dsr, 2);
tqma6_bb_ft_board_setup(blob, bd);
}
#endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */
Reference in a new issue View git blame Copy permalink