u-boot/drivers/usb/dwc3/dwc3-generic.c
Vignesh Raghavendra cab4e275dd dwc3-generic: Add support for AM654 USB controller
AM654 has DWC3 USB controller that is very similar to other TI SoCs. Add
a new compatible to enable the same.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20 10:10:29 +05:30

442 lines
9.9 KiB
C

// SPDX-License-Identifier: GPL-2.0
/*
* Generic DWC3 Glue layer
*
* Copyright (C) 2016 - 2018 Xilinx, Inc.
*
* Based on dwc3-omap.c.
*/
#include <common.h>
#include <cpu_func.h>
#include <asm-generic/io.h>
#include <dm.h>
#include <dm/device-internal.h>
#include <dm/lists.h>
#include <dwc3-uboot.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
#include <malloc.h>
#include <usb.h>
#include "core.h"
#include "gadget.h"
#include <reset.h>
#include <clk.h>
#include <usb/xhci.h>
struct dwc3_generic_plat {
fdt_addr_t base;
u32 maximum_speed;
enum usb_dr_mode dr_mode;
};
struct dwc3_generic_priv {
void *base;
struct dwc3 dwc3;
struct phy *phys;
int num_phys;
};
struct dwc3_generic_host_priv {
struct xhci_ctrl xhci_ctrl;
struct dwc3_generic_priv gen_priv;
};
static int dwc3_generic_probe(struct udevice *dev,
struct dwc3_generic_priv *priv)
{
int rc;
struct dwc3_generic_plat *plat = dev_get_platdata(dev);
struct dwc3 *dwc3 = &priv->dwc3;
dwc3->dev = dev;
dwc3->maximum_speed = plat->maximum_speed;
dwc3->dr_mode = plat->dr_mode;
#if CONFIG_IS_ENABLED(OF_CONTROL)
dwc3_of_parse(dwc3);
#endif
rc = dwc3_setup_phy(dev, &priv->phys, &priv->num_phys);
if (rc)
return rc;
priv->base = map_physmem(plat->base, DWC3_OTG_REGS_END, MAP_NOCACHE);
dwc3->regs = priv->base + DWC3_GLOBALS_REGS_START;
rc = dwc3_init(dwc3);
if (rc) {
unmap_physmem(priv->base, MAP_NOCACHE);
return rc;
}
return 0;
}
static int dwc3_generic_remove(struct udevice *dev,
struct dwc3_generic_priv *priv)
{
struct dwc3 *dwc3 = &priv->dwc3;
dwc3_remove(dwc3);
dwc3_shutdown_phy(dev, priv->phys, priv->num_phys);
unmap_physmem(dwc3->regs, MAP_NOCACHE);
return 0;
}
static int dwc3_generic_ofdata_to_platdata(struct udevice *dev)
{
struct dwc3_generic_plat *plat = dev_get_platdata(dev);
int node = dev_of_offset(dev);
plat->base = devfdt_get_addr(dev);
plat->maximum_speed = usb_get_maximum_speed(node);
if (plat->maximum_speed == USB_SPEED_UNKNOWN) {
pr_info("No USB maximum speed specified. Using super speed\n");
plat->maximum_speed = USB_SPEED_SUPER;
}
plat->dr_mode = usb_get_dr_mode(node);
if (plat->dr_mode == USB_DR_MODE_UNKNOWN) {
pr_err("Invalid usb mode setup\n");
return -ENODEV;
}
return 0;
}
#if CONFIG_IS_ENABLED(DM_USB_GADGET)
int dm_usb_gadget_handle_interrupts(struct udevice *dev)
{
struct dwc3_generic_priv *priv = dev_get_priv(dev);
struct dwc3 *dwc3 = &priv->dwc3;
dwc3_gadget_uboot_handle_interrupt(dwc3);
return 0;
}
static int dwc3_generic_peripheral_probe(struct udevice *dev)
{
struct dwc3_generic_priv *priv = dev_get_priv(dev);
return dwc3_generic_probe(dev, priv);
}
static int dwc3_generic_peripheral_remove(struct udevice *dev)
{
struct dwc3_generic_priv *priv = dev_get_priv(dev);
return dwc3_generic_remove(dev, priv);
}
U_BOOT_DRIVER(dwc3_generic_peripheral) = {
.name = "dwc3-generic-peripheral",
.id = UCLASS_USB_GADGET_GENERIC,
.ofdata_to_platdata = dwc3_generic_ofdata_to_platdata,
.probe = dwc3_generic_peripheral_probe,
.remove = dwc3_generic_peripheral_remove,
.priv_auto_alloc_size = sizeof(struct dwc3_generic_priv),
.platdata_auto_alloc_size = sizeof(struct dwc3_generic_plat),
};
#endif
#if defined(CONFIG_SPL_USB_HOST_SUPPORT) || !defined(CONFIG_SPL_BUILD)
static int dwc3_generic_host_probe(struct udevice *dev)
{
struct xhci_hcor *hcor;
struct xhci_hccr *hccr;
struct dwc3_generic_host_priv *priv = dev_get_priv(dev);
int rc;
rc = dwc3_generic_probe(dev, &priv->gen_priv);
if (rc)
return rc;
hccr = (struct xhci_hccr *)priv->gen_priv.base;
hcor = (struct xhci_hcor *)(priv->gen_priv.base +
HC_LENGTH(xhci_readl(&(hccr)->cr_capbase)));
return xhci_register(dev, hccr, hcor);
}
static int dwc3_generic_host_remove(struct udevice *dev)
{
struct dwc3_generic_host_priv *priv = dev_get_priv(dev);
int rc;
rc = xhci_deregister(dev);
if (rc)
return rc;
return dwc3_generic_remove(dev, &priv->gen_priv);
}
U_BOOT_DRIVER(dwc3_generic_host) = {
.name = "dwc3-generic-host",
.id = UCLASS_USB,
.ofdata_to_platdata = dwc3_generic_ofdata_to_platdata,
.probe = dwc3_generic_host_probe,
.remove = dwc3_generic_host_remove,
.priv_auto_alloc_size = sizeof(struct dwc3_generic_host_priv),
.platdata_auto_alloc_size = sizeof(struct dwc3_generic_plat),
.ops = &xhci_usb_ops,
.flags = DM_FLAG_ALLOC_PRIV_DMA,
};
#endif
struct dwc3_glue_data {
struct clk_bulk clks;
struct reset_ctl_bulk resets;
fdt_addr_t regs;
};
struct dwc3_glue_ops {
void (*select_dr_mode)(struct udevice *dev, int index,
enum usb_dr_mode mode);
};
void dwc3_ti_select_dr_mode(struct udevice *dev, int index,
enum usb_dr_mode mode)
{
#define USBOTGSS_UTMI_OTG_STATUS 0x0084
#define USBOTGSS_UTMI_OTG_OFFSET 0x0480
/* UTMI_OTG_STATUS REGISTER */
#define USBOTGSS_UTMI_OTG_STATUS_SW_MODE BIT(31)
#define USBOTGSS_UTMI_OTG_STATUS_POWERPRESENT BIT(9)
#define USBOTGSS_UTMI_OTG_STATUS_TXBITSTUFFENABLE BIT(8)
#define USBOTGSS_UTMI_OTG_STATUS_IDDIG BIT(4)
#define USBOTGSS_UTMI_OTG_STATUS_SESSEND BIT(3)
#define USBOTGSS_UTMI_OTG_STATUS_SESSVALID BIT(2)
#define USBOTGSS_UTMI_OTG_STATUS_VBUSVALID BIT(1)
enum dwc3_omap_utmi_mode {
DWC3_OMAP_UTMI_MODE_UNKNOWN = 0,
DWC3_OMAP_UTMI_MODE_HW,
DWC3_OMAP_UTMI_MODE_SW,
};
u32 use_id_pin;
u32 host_mode;
u32 reg;
u32 utmi_mode;
u32 utmi_status_offset = USBOTGSS_UTMI_OTG_STATUS;
struct dwc3_glue_data *glue = dev_get_platdata(dev);
void *base = map_physmem(glue->regs, 0x10000, MAP_NOCACHE);
if (device_is_compatible(dev, "ti,am437x-dwc3"))
utmi_status_offset += USBOTGSS_UTMI_OTG_OFFSET;
utmi_mode = dev_read_u32_default(dev, "utmi-mode",
DWC3_OMAP_UTMI_MODE_UNKNOWN);
if (utmi_mode != DWC3_OMAP_UTMI_MODE_HW) {
debug("%s: OTG is not supported. defaulting to PERIPHERAL\n",
dev->name);
mode = USB_DR_MODE_PERIPHERAL;
}
switch (mode) {
case USB_DR_MODE_PERIPHERAL:
use_id_pin = 0;
host_mode = 0;
break;
case USB_DR_MODE_HOST:
use_id_pin = 0;
host_mode = 1;
break;
case USB_DR_MODE_OTG:
default:
use_id_pin = 1;
host_mode = 0;
break;
}
reg = readl(base + utmi_status_offset);
reg &= ~(USBOTGSS_UTMI_OTG_STATUS_SW_MODE);
if (!use_id_pin)
reg |= USBOTGSS_UTMI_OTG_STATUS_SW_MODE;
writel(reg, base + utmi_status_offset);
reg &= ~(USBOTGSS_UTMI_OTG_STATUS_SESSEND |
USBOTGSS_UTMI_OTG_STATUS_VBUSVALID |
USBOTGSS_UTMI_OTG_STATUS_IDDIG);
reg |= USBOTGSS_UTMI_OTG_STATUS_SESSVALID |
USBOTGSS_UTMI_OTG_STATUS_POWERPRESENT;
if (!host_mode)
reg |= USBOTGSS_UTMI_OTG_STATUS_IDDIG |
USBOTGSS_UTMI_OTG_STATUS_VBUSVALID;
writel(reg, base + utmi_status_offset);
unmap_physmem(base, MAP_NOCACHE);
}
struct dwc3_glue_ops ti_ops = {
.select_dr_mode = dwc3_ti_select_dr_mode,
};
static int dwc3_glue_bind(struct udevice *parent)
{
const void *fdt = gd->fdt_blob;
int node;
int ret;
for (node = fdt_first_subnode(fdt, dev_of_offset(parent)); node > 0;
node = fdt_next_subnode(fdt, node)) {
const char *name = fdt_get_name(fdt, node, NULL);
enum usb_dr_mode dr_mode;
struct udevice *dev;
const char *driver = NULL;
debug("%s: subnode name: %s\n", __func__, name);
dr_mode = usb_get_dr_mode(node);
switch (dr_mode) {
case USB_DR_MODE_PERIPHERAL:
case USB_DR_MODE_OTG:
#if CONFIG_IS_ENABLED(DM_USB_GADGET)
debug("%s: dr_mode: OTG or Peripheral\n", __func__);
driver = "dwc3-generic-peripheral";
#endif
break;
#if defined(CONFIG_SPL_USB_HOST_SUPPORT) || !defined(CONFIG_SPL_BUILD)
case USB_DR_MODE_HOST:
debug("%s: dr_mode: HOST\n", __func__);
driver = "dwc3-generic-host";
break;
#endif
default:
debug("%s: unsupported dr_mode\n", __func__);
return -ENODEV;
};
if (!driver)
continue;
ret = device_bind_driver_to_node(parent, driver, name,
offset_to_ofnode(node), &dev);
if (ret) {
debug("%s: not able to bind usb device mode\n",
__func__);
return ret;
}
}
return 0;
}
static int dwc3_glue_reset_init(struct udevice *dev,
struct dwc3_glue_data *glue)
{
int ret;
ret = reset_get_bulk(dev, &glue->resets);
if (ret == -ENOTSUPP || ret == -ENOENT)
return 0;
else if (ret)
return ret;
ret = reset_deassert_bulk(&glue->resets);
if (ret) {
reset_release_bulk(&glue->resets);
return ret;
}
return 0;
}
static int dwc3_glue_clk_init(struct udevice *dev,
struct dwc3_glue_data *glue)
{
int ret;
ret = clk_get_bulk(dev, &glue->clks);
if (ret == -ENOSYS || ret == -ENOENT)
return 0;
if (ret)
return ret;
#if CONFIG_IS_ENABLED(CLK)
ret = clk_enable_bulk(&glue->clks);
if (ret) {
clk_release_bulk(&glue->clks);
return ret;
}
#endif
return 0;
}
static int dwc3_glue_probe(struct udevice *dev)
{
struct dwc3_glue_ops *ops = (struct dwc3_glue_ops *)dev_get_driver_data(dev);
struct dwc3_glue_data *glue = dev_get_platdata(dev);
struct udevice *child = NULL;
int index = 0;
int ret;
glue->regs = dev_read_addr(dev);
ret = dwc3_glue_clk_init(dev, glue);
if (ret)
return ret;
ret = dwc3_glue_reset_init(dev, glue);
if (ret)
return ret;
ret = device_find_first_child(dev, &child);
if (ret)
return ret;
while (child) {
enum usb_dr_mode dr_mode;
dr_mode = usb_get_dr_mode(dev_of_offset(child));
device_find_next_child(&child);
if (ops && ops->select_dr_mode)
ops->select_dr_mode(dev, index, dr_mode);
index++;
}
return 0;
}
static int dwc3_glue_remove(struct udevice *dev)
{
struct dwc3_glue_data *glue = dev_get_platdata(dev);
reset_release_bulk(&glue->resets);
clk_release_bulk(&glue->clks);
return 0;
}
static const struct udevice_id dwc3_glue_ids[] = {
{ .compatible = "xlnx,zynqmp-dwc3" },
{ .compatible = "ti,keystone-dwc3"},
{ .compatible = "ti,dwc3", .data = (ulong)&ti_ops },
{ .compatible = "ti,am437x-dwc3", .data = (ulong)&ti_ops },
{ .compatible = "ti,am654-dwc3" },
{ }
};
U_BOOT_DRIVER(dwc3_generic_wrapper) = {
.name = "dwc3-generic-wrapper",
.id = UCLASS_NOP,
.of_match = dwc3_glue_ids,
.bind = dwc3_glue_bind,
.probe = dwc3_glue_probe,
.remove = dwc3_glue_remove,
.platdata_auto_alloc_size = sizeof(struct dwc3_glue_data),
};