mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-12 22:33:18 +00:00
83d290c56f
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
115 lines
2.1 KiB
C
115 lines
2.1 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2014, STMicroelectronics - All Rights Reserved
|
|
* Author(s): Vikas Manocha, <vikas.manocha@st.com> for STMicroelectronics.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <dm.h>
|
|
#include <miiphy.h>
|
|
#include <asm/arch/stv0991_periph.h>
|
|
#include <asm/arch/stv0991_defs.h>
|
|
#include <asm/arch/hardware.h>
|
|
#include <asm/arch/gpio.h>
|
|
#include <netdev.h>
|
|
#include <asm/io.h>
|
|
#include <dm/platform_data/serial_pl01x.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
struct gpio_regs *const gpioa_regs =
|
|
(struct gpio_regs *) GPIOA_BASE_ADDR;
|
|
|
|
#ifndef CONFIG_OF_CONTROL
|
|
static const struct pl01x_serial_platdata serial_platdata = {
|
|
.base = 0x80406000,
|
|
.type = TYPE_PL011,
|
|
.clock = 2700 * 1000,
|
|
};
|
|
|
|
U_BOOT_DEVICE(stv09911_serials) = {
|
|
.name = "serial_pl01x",
|
|
.platdata = &serial_platdata,
|
|
};
|
|
#endif
|
|
|
|
#ifdef CONFIG_SHOW_BOOT_PROGRESS
|
|
void show_boot_progress(int progress)
|
|
{
|
|
printf("%i\n", progress);
|
|
}
|
|
#endif
|
|
|
|
void enable_eth_phy(void)
|
|
{
|
|
/* Set GPIOA_06 pad HIGH (Appli board)*/
|
|
writel(readl(&gpioa_regs->dir) | 0x40, &gpioa_regs->dir);
|
|
writel(readl(&gpioa_regs->data) | 0x40, &gpioa_regs->data);
|
|
}
|
|
int board_eth_enable(void)
|
|
{
|
|
stv0991_pinmux_config(ETH_GPIOB_10_31_C_0_4);
|
|
clock_setup(ETH_CLOCK_CFG);
|
|
enable_eth_phy();
|
|
return 0;
|
|
}
|
|
|
|
int board_qspi_enable(void)
|
|
{
|
|
stv0991_pinmux_config(QSPI_CS_CLK_PAD);
|
|
clock_setup(QSPI_CLOCK_CFG);
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Miscellaneous platform dependent initialisations
|
|
*/
|
|
int board_init(void)
|
|
{
|
|
board_eth_enable();
|
|
board_qspi_enable();
|
|
return 0;
|
|
}
|
|
|
|
int board_uart_init(void)
|
|
{
|
|
stv0991_pinmux_config(UART_GPIOC_30_31);
|
|
clock_setup(UART_CLOCK_CFG);
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_BOARD_EARLY_INIT_F
|
|
int board_early_init_f(void)
|
|
{
|
|
board_uart_init();
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = PHYS_SDRAM_1_SIZE;
|
|
return 0;
|
|
}
|
|
|
|
int dram_init_banksize(void)
|
|
{
|
|
gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
|
|
gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_CMD_NET
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
int ret = 0;
|
|
|
|
#if defined(CONFIG_ETH_DESIGNWARE)
|
|
u32 interface = PHY_INTERFACE_MODE_MII;
|
|
if (designware_initialize(GMAC_BASE_ADDR, interface) >= 0)
|
|
ret++;
|
|
#endif
|
|
return ret;
|
|
}
|
|
#endif
|