u-boot/drivers/power/axp209.c

// SPDX-License-Identifier: GPL-2.0+
/*
 * (C) Copyright 2012
 * Henrik Nordstrom <henrik@henriknordstrom.net>
 */

#include <common.h>
#include <command.h>
#include <asm/arch/pmic_bus.h>
#include <axp_pmic.h>

static u8 axp209_mvolt_to_cfg(int mvolt, int min, int max, int div)
{
	if (mvolt < min)
		mvolt = min;
	else if (mvolt > max)
		mvolt = max;

	return (mvolt - min) / div;
}

int axp_set_dcdc2(unsigned int mvolt)
{
	int rc;
	u8 cfg, current;

	if (mvolt == 0)
		return pmic_bus_clrbits(AXP209_OUTPUT_CTRL,
					AXP209_OUTPUT_CTRL_DCDC2);

	rc = pmic_bus_setbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_DCDC2);
	if (rc)
		return rc;

	cfg = axp209_mvolt_to_cfg(mvolt, 700, 2275, 25);

	/* Do we really need to be this gentle? It has built-in voltage slope */
	while ((rc = pmic_bus_read(AXP209_DCDC2_VOLTAGE, &current)) == 0 &&
	       current != cfg) {
		if (current < cfg)
			current++;
		else
			current--;

		rc = pmic_bus_write(AXP209_DCDC2_VOLTAGE, current);
		if (rc)
			break;
	}

	return rc;
}

int axp_set_dcdc3(unsigned int mvolt)
{
	u8 cfg = axp209_mvolt_to_cfg(mvolt, 700, 3500, 25);
	int rc;

	if (mvolt == 0)
		return pmic_bus_clrbits(AXP209_OUTPUT_CTRL,
					AXP209_OUTPUT_CTRL_DCDC3);

	rc = pmic_bus_write(AXP209_DCDC3_VOLTAGE, cfg);
	if (rc)
		return rc;

	return pmic_bus_setbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_DCDC3);
}

int axp_set_aldo2(unsigned int mvolt)
{
	int rc;
	u8 cfg, reg;

	if (mvolt == 0)
		return pmic_bus_clrbits(AXP209_OUTPUT_CTRL,
					AXP209_OUTPUT_CTRL_LDO2);

	cfg = axp209_mvolt_to_cfg(mvolt, 1800, 3300, 100);

	rc = pmic_bus_read(AXP209_LDO24_VOLTAGE, &reg);
	if (rc)
		return rc;

	/* LDO2 configuration is in upper 4 bits */
	reg = (reg & 0x0f) | (cfg << 4);
	rc = pmic_bus_write(AXP209_LDO24_VOLTAGE, reg);
	if (rc)
		return rc;

	return pmic_bus_setbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_LDO2);
}

int axp_set_aldo3(unsigned int mvolt)
{
	u8 cfg;
	int rc;

	if (mvolt == 0)
		return pmic_bus_clrbits(AXP209_OUTPUT_CTRL,
					AXP209_OUTPUT_CTRL_LDO3);

	if (mvolt == -1)
		cfg = 0x80;	/* determined by LDO3IN pin */
	else
		cfg = axp209_mvolt_to_cfg(mvolt, 700, 3500, 25);

	rc = pmic_bus_write(AXP209_LDO3_VOLTAGE, cfg);
	if (rc)
		return rc;

	return pmic_bus_setbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_LDO3);
}

int axp_set_aldo4(unsigned int mvolt)
{
	int rc;
	static const unsigned int vindex[] = {
		1250, 1300, 1400, 1500, 1600, 1700, 1800, 1900, 2000, 2500,
		2700, 2800, 3000, 3100, 3200, 3300
	};
	u8 cfg, reg;

	if (mvolt == 0)
		return pmic_bus_clrbits(AXP209_OUTPUT_CTRL,
					AXP209_OUTPUT_CTRL_LDO4);

	/* Translate mvolt to register cfg value, requested <= selected */
	for (cfg = 15; vindex[cfg] > mvolt && cfg > 0; cfg--);

	rc = pmic_bus_read(AXP209_LDO24_VOLTAGE, &reg);
	if (rc)
		return rc;

	/* LDO4 configuration is in lower 4 bits */
	reg = (reg & 0xf0) | (cfg << 0);
	rc = pmic_bus_write(AXP209_LDO24_VOLTAGE, reg);
	if (rc)
		return rc;

	return pmic_bus_setbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_LDO4);
}

int axp_init(void)
{
	u8 ver;
	int i, rc;

	rc = pmic_bus_init();
	if (rc)
		return rc;

	rc = pmic_bus_read(AXP209_CHIP_VERSION, &ver);
	if (rc)
		return rc;

	/* Low 4 bits is chip version */
	ver &= 0x0f;

	if (ver != 0x1)
		return -EINVAL;

	/* Mask all interrupts */
	for (i = AXP209_IRQ_ENABLE1; i <= AXP209_IRQ_ENABLE5; i++) {
		rc = pmic_bus_write(i, 0);
		if (rc)
			return rc;
	}

	/*
	 * Turn off LDOIO regulators / tri-state GPIO pins, when rebooting
	 * from android these are sometimes on.
	 */
	rc = pmic_bus_write(AXP_GPIO0_CTRL, AXP_GPIO_CTRL_INPUT);
	if (rc)
		return rc;

	rc = pmic_bus_write(AXP_GPIO1_CTRL, AXP_GPIO_CTRL_INPUT);
	if (rc)
		return rc;

	rc = pmic_bus_write(AXP_GPIO2_CTRL, AXP_GPIO_CTRL_INPUT);
	if (rc)
		return rc;

	return 0;
}

int do_poweroff(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
	pmic_bus_write(AXP209_SHUTDOWN, AXP209_POWEROFF);

	/* infinite loop during shutdown */
	while (1) {}

	/* not reached */
	return 0;
}