u-boot/drivers/mtd/spi/ramtron.c
Jagannadha Sutradharudu Teki adbb5860e5 sf: ramtron: Remove page_size print
There is no page_size for ramtron flashes,
so just print the detected flash and it's size.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2013-10-07 19:35:09 +05:30

403 lines
9.9 KiB
C

/*
* (C) Copyright 2010
* Reinhard Meyer, EMK Elektronik, reinhard.meyer@emk-elektronik.de
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* Note: RAMTRON SPI FRAMs are ferroelectric, nonvolatile RAMs
* with an interface identical to SPI flash devices.
* However since they behave like RAM there are no delays or
* busy polls required. They can sustain read or write at the
* allowed SPI bus speed, which can be 40 MHz for some devices.
*
* Unfortunately some RAMTRON devices do not have a means of
* identifying them. They will leave the SO line undriven when
* the READ-ID command is issued. It is therefore mandatory
* that the MISO line has a proper pull-up, so that READ-ID
* will return a row of 0xff. This 0xff pseudo-id will cause
* probes by all vendor specific functions that are designed
* to handle it. If the MISO line is not pulled up, READ-ID
* could return any random noise, even mimicking another
* device.
*
* We use CONFIG_SPI_FRAM_RAMTRON_NON_JEDEC
* to define which device will be assumed after a simple status
* register verify. This method is prone to false positive
* detection and should therefore be the last to be tried.
* Enter it in the last position in the table in spi_flash.c!
*
* The define CONFIG_SPI_FRAM_RAMTRON_NON_JEDEC both activates
* compilation of the special handler and defines the device
* to assume.
*/
#include <common.h>
#include <malloc.h>
#include <spi_flash.h>
#include "sf_internal.h"
/*
* Properties of supported FRAMs
* Note: speed is currently not used because we have no method to deliver that
* value to the upper layers
*/
struct ramtron_spi_fram_params {
u32 size; /* size in bytes */
u8 addr_len; /* number of address bytes */
u8 merge_cmd; /* some address bits are in the command byte */
u8 id1; /* device ID 1 (family, density) */
u8 id2; /* device ID 2 (sub, rev, rsvd) */
u32 speed; /* max. SPI clock in Hz */
const char *name; /* name for display and/or matching */
};
struct ramtron_spi_fram {
struct spi_flash flash;
const struct ramtron_spi_fram_params *params;
};
static inline struct ramtron_spi_fram *to_ramtron_spi_fram(struct spi_flash
*flash)
{
return container_of(flash, struct ramtron_spi_fram, flash);
}
/*
* table describing supported FRAM chips:
* chips without RDID command must have the values 0xff for id1 and id2
*/
static const struct ramtron_spi_fram_params ramtron_spi_fram_table[] = {
{
.size = 32*1024,
.addr_len = 2,
.merge_cmd = 0,
.id1 = 0x22,
.id2 = 0x00,
.speed = 40000000,
.name = "FM25V02",
},
{
.size = 32*1024,
.addr_len = 2,
.merge_cmd = 0,
.id1 = 0x22,
.id2 = 0x01,
.speed = 40000000,
.name = "FM25VN02",
},
{
.size = 64*1024,
.addr_len = 2,
.merge_cmd = 0,
.id1 = 0x23,
.id2 = 0x00,
.speed = 40000000,
.name = "FM25V05",
},
{
.size = 64*1024,
.addr_len = 2,
.merge_cmd = 0,
.id1 = 0x23,
.id2 = 0x01,
.speed = 40000000,
.name = "FM25VN05",
},
{
.size = 128*1024,
.addr_len = 3,
.merge_cmd = 0,
.id1 = 0x24,
.id2 = 0x00,
.speed = 40000000,
.name = "FM25V10",
},
{
.size = 128*1024,
.addr_len = 3,
.merge_cmd = 0,
.id1 = 0x24,
.id2 = 0x01,
.speed = 40000000,
.name = "FM25VN10",
},
#ifdef CONFIG_SPI_FRAM_RAMTRON_NON_JEDEC
{
.size = 256*1024,
.addr_len = 3,
.merge_cmd = 0,
.id1 = 0xff,
.id2 = 0xff,
.speed = 40000000,
.name = "FM25H20",
},
#endif
};
static int ramtron_common(struct spi_flash *flash,
u32 offset, size_t len, void *buf, u8 command)
{
struct ramtron_spi_fram *sn = to_ramtron_spi_fram(flash);
u8 cmd[4];
int cmd_len;
int ret;
if (sn->params->addr_len == 3 && sn->params->merge_cmd == 0) {
cmd[0] = command;
cmd[1] = offset >> 16;
cmd[2] = offset >> 8;
cmd[3] = offset;
cmd_len = 4;
} else if (sn->params->addr_len == 2 && sn->params->merge_cmd == 0) {
cmd[0] = command;
cmd[1] = offset >> 8;
cmd[2] = offset;
cmd_len = 3;
} else {
printf("SF: unsupported addr_len or merge_cmd\n");
return -1;
}
/* claim the bus */
ret = spi_claim_bus(flash->spi);
if (ret) {
debug("SF: Unable to claim SPI bus\n");
return ret;
}
if (command == CMD_PAGE_PROGRAM) {
/* send WREN */
ret = spi_flash_cmd_write_enable(flash);
if (ret < 0) {
debug("SF: Enabling Write failed\n");
goto releasebus;
}
}
/* do the transaction */
if (command == CMD_PAGE_PROGRAM)
ret = spi_flash_cmd_write(flash->spi, cmd, cmd_len, buf, len);
else
ret = spi_flash_cmd_read(flash->spi, cmd, cmd_len, buf, len);
if (ret < 0)
debug("SF: Transaction failed\n");
releasebus:
/* release the bus */
spi_release_bus(flash->spi);
return ret;
}
static int ramtron_read(struct spi_flash *flash,
u32 offset, size_t len, void *buf)
{
return ramtron_common(flash, offset, len, buf,
CMD_READ_ARRAY_SLOW);
}
static int ramtron_write(struct spi_flash *flash,
u32 offset, size_t len, const void *buf)
{
return ramtron_common(flash, offset, len, (void *)buf,
CMD_PAGE_PROGRAM);
}
static int ramtron_erase(struct spi_flash *flash, u32 offset, size_t len)
{
debug("SF: Erase of RAMTRON FRAMs is pointless\n");
return -1;
}
/*
* nore: we are called here with idcode pointing to the first non-0x7f byte
* already!
*/
static struct spi_flash *spi_fram_probe_ramtron(struct spi_slave *spi,
u8 *idcode)
{
const struct ramtron_spi_fram_params *params;
struct ramtron_spi_fram *sn;
unsigned int i;
#ifdef CONFIG_SPI_FRAM_RAMTRON_NON_JEDEC
int ret;
u8 sr;
#endif
/* NOTE: the bus has been claimed before this function is called! */
switch (idcode[0]) {
case 0xc2:
/* JEDEC conformant RAMTRON id */
for (i = 0; i < ARRAY_SIZE(ramtron_spi_fram_table); i++) {
params = &ramtron_spi_fram_table[i];
if (idcode[1] == params->id1 &&
idcode[2] == params->id2)
goto found;
}
break;
#ifdef CONFIG_SPI_FRAM_RAMTRON_NON_JEDEC
case 0xff:
/*
* probably open MISO line, pulled up.
* We COULD have a non JEDEC conformant FRAM here,
* read the status register to verify
*/
ret = spi_flash_cmd(spi, CMD_READ_STATUS, &sr, 1);
if (ret)
return NULL;
/* Bits 5,4,0 are fixed 0 for all devices */
if ((sr & 0x31) != 0x00)
return NULL;
/* now find the device */
for (i = 0; i < ARRAY_SIZE(ramtron_spi_fram_table); i++) {
params = &ramtron_spi_fram_table[i];
if (!strcmp(params->name,
CONFIG_SPI_FRAM_RAMTRON_NON_JEDEC))
goto found;
}
debug("SF: Unsupported non-JEDEC RAMTRON device "
CONFIG_SPI_FRAM_RAMTRON_NON_JEDEC "\n");
break;
#endif
default:
break;
}
/* arriving here means no method has found a device we can handle */
debug("SF/ramtron: unsupported device id0=%02x id1=%02x id2=%02x\n",
idcode[0], idcode[1], idcode[2]);
return NULL;
found:
sn = malloc(sizeof(*sn));
if (!sn) {
debug("SF: Failed to allocate memory\n");
return NULL;
}
sn->params = params;
sn->flash.write = ramtron_write;
sn->flash.read = ramtron_read;
sn->flash.erase = ramtron_erase;
sn->flash.size = params->size;
return &sn->flash;
}
/*
* The following table holds all device probe functions
* (All flashes are removed and implemented a common probe at
* spi_flash_probe.c)
*
* shift: number of continuation bytes before the ID
* idcode: the expected IDCODE or 0xff for non JEDEC devices
* probe: the function to call
*
* Non JEDEC devices should be ordered in the table such that
* the probe functions with best detection algorithms come first.
*
* Several matching entries are permitted, they will be tried
* in sequence until a probe function returns non NULL.
*
* IDCODE_CONT_LEN may be redefined if a device needs to declare a
* larger "shift" value. IDCODE_PART_LEN generally shouldn't be
* changed. This is the max number of bytes probe functions may
* examine when looking up part-specific identification info.
*
* Probe functions will be given the idcode buffer starting at their
* manu id byte (the "idcode" in the table below). In other words,
* all of the continuation bytes will be skipped (the "shift" below).
*/
#define IDCODE_CONT_LEN 0
#define IDCODE_PART_LEN 5
static const struct {
const u8 shift;
const u8 idcode;
struct spi_flash *(*probe) (struct spi_slave *spi, u8 *idcode);
} flashes[] = {
/* Keep it sorted by define name */
#ifdef CONFIG_SPI_FRAM_RAMTRON
{ 6, 0xc2, spi_fram_probe_ramtron, },
# undef IDCODE_CONT_LEN
# define IDCODE_CONT_LEN 6
#endif
#ifdef CONFIG_SPI_FRAM_RAMTRON_NON_JEDEC
{ 0, 0xff, spi_fram_probe_ramtron, },
#endif
};
#define IDCODE_LEN (IDCODE_CONT_LEN + IDCODE_PART_LEN)
struct spi_flash *spi_flash_probe(unsigned int bus, unsigned int cs,
unsigned int max_hz, unsigned int spi_mode)
{
struct spi_slave *spi;
struct spi_flash *flash = NULL;
int ret, i, shift;
u8 idcode[IDCODE_LEN], *idp;
spi = spi_setup_slave(bus, cs, max_hz, spi_mode);
if (!spi) {
printf("SF: Failed to set up slave\n");
return NULL;
}
ret = spi_claim_bus(spi);
if (ret) {
debug("SF: Failed to claim SPI bus: %d\n", ret);
goto err_claim_bus;
}
/* Read the ID codes */
ret = spi_flash_cmd(spi, CMD_READ_ID, idcode, sizeof(idcode));
if (ret)
goto err_read_id;
#ifdef DEBUG
printf("SF: Got idcodes\n");
print_buffer(0, idcode, 1, sizeof(idcode), 0);
#endif
/* count the number of continuation bytes */
for (shift = 0, idp = idcode;
shift < IDCODE_CONT_LEN && *idp == 0x7f;
++shift, ++idp)
continue;
/* search the table for matches in shift and id */
for (i = 0; i < ARRAY_SIZE(flashes); ++i)
if (flashes[i].shift == shift && flashes[i].idcode == *idp) {
/* we have a match, call probe */
flash = flashes[i].probe(spi, idp);
if (flash)
break;
}
if (!flash) {
printf("SF: Unsupported manufacturer %02x\n", *idp);
goto err_manufacturer_probe;
}
printf("SF: Detected %s with total size ", flash->name);
print_size(flash->size, "");
puts("\n");
spi_release_bus(spi);
return flash;
err_manufacturer_probe:
err_read_id:
spi_release_bus(spi);
err_claim_bus:
spi_free_slave(spi);
return NULL;
}
void spi_flash_free(struct spi_flash *flash)
{
spi_free_slave(flash->spi);
free(flash);
}