mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-23 03:23:47 +00:00
401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
166 lines
3.8 KiB
C
166 lines
3.8 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Board functions for Compulab CM-T335 board
|
|
*
|
|
* Copyright (C) 2013, Compulab Ltd - http://compulab.co.il/
|
|
*
|
|
* Author: Ilya Ledvich <ilya@compulab.co.il>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <env.h>
|
|
#include <errno.h>
|
|
#include <miiphy.h>
|
|
#include <net.h>
|
|
#include <status_led.h>
|
|
#include <cpsw.h>
|
|
#include <asm/global_data.h>
|
|
#include <linux/delay.h>
|
|
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/arch/hardware_am33xx.h>
|
|
#include <asm/io.h>
|
|
#include <asm/gpio.h>
|
|
|
|
#include "../common/eeprom.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/*
|
|
* Basic board specific setup. Pinmux has been handled already.
|
|
*/
|
|
int board_init(void)
|
|
{
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
|
|
gpmc_init();
|
|
|
|
#if defined(CONFIG_LED_STATUS) && defined(CONFIG_LED_STATUS_BOOT_ENABLE)
|
|
status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_OFF);
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
#if defined (CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)
|
|
static void cpsw_control(int enabled)
|
|
{
|
|
/* VTP can be added here */
|
|
return;
|
|
}
|
|
|
|
static struct cpsw_slave_data cpsw_slave = {
|
|
.slave_reg_ofs = 0x208,
|
|
.sliver_reg_ofs = 0xd80,
|
|
.phy_addr = 0,
|
|
.phy_if = PHY_INTERFACE_MODE_RGMII,
|
|
};
|
|
|
|
static struct cpsw_platform_data cpsw_data = {
|
|
.mdio_base = CPSW_MDIO_BASE,
|
|
.cpsw_base = CPSW_BASE,
|
|
.mdio_div = 0xff,
|
|
.channels = 8,
|
|
.cpdma_reg_ofs = 0x800,
|
|
.slaves = 1,
|
|
.slave_data = &cpsw_slave,
|
|
.ale_reg_ofs = 0xd00,
|
|
.ale_entries = 1024,
|
|
.host_port_reg_ofs = 0x108,
|
|
.hw_stats_reg_ofs = 0x900,
|
|
.bd_ram_ofs = 0x2000,
|
|
.mac_control = (1 << 5),
|
|
.control = cpsw_control,
|
|
.host_port_num = 0,
|
|
.version = CPSW_CTRL_VERSION_2,
|
|
};
|
|
|
|
/* PHY reset GPIO */
|
|
#define GPIO_PHY_RST GPIO_PIN(3, 7)
|
|
|
|
static void board_phy_init(void)
|
|
{
|
|
gpio_request(GPIO_PHY_RST, "phy_rst");
|
|
gpio_direction_output(GPIO_PHY_RST, 0);
|
|
mdelay(2);
|
|
gpio_set_value(GPIO_PHY_RST, 1);
|
|
mdelay(2);
|
|
}
|
|
|
|
static void get_efuse_mac_addr(uchar *enetaddr)
|
|
{
|
|
uint32_t mac_hi, mac_lo;
|
|
struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
|
|
|
|
mac_lo = readl(&cdev->macid0l);
|
|
mac_hi = readl(&cdev->macid0h);
|
|
enetaddr[0] = mac_hi & 0xFF;
|
|
enetaddr[1] = (mac_hi & 0xFF00) >> 8;
|
|
enetaddr[2] = (mac_hi & 0xFF0000) >> 16;
|
|
enetaddr[3] = (mac_hi & 0xFF000000) >> 24;
|
|
enetaddr[4] = mac_lo & 0xFF;
|
|
enetaddr[5] = (mac_lo & 0xFF00) >> 8;
|
|
}
|
|
|
|
/*
|
|
* Routine: handle_mac_address
|
|
* Description: prepare MAC address for on-board Ethernet.
|
|
*/
|
|
static int handle_mac_address(void)
|
|
{
|
|
uchar enetaddr[6];
|
|
int rv;
|
|
|
|
rv = eth_env_get_enetaddr("ethaddr", enetaddr);
|
|
if (rv)
|
|
return 0;
|
|
|
|
rv = cl_eeprom_read_mac_addr(enetaddr, CONFIG_SYS_I2C_EEPROM_BUS);
|
|
if (rv)
|
|
get_efuse_mac_addr(enetaddr);
|
|
|
|
if (!is_valid_ethaddr(enetaddr))
|
|
return -1;
|
|
|
|
return eth_env_set_enetaddr("ethaddr", enetaddr);
|
|
}
|
|
|
|
#define AR8051_PHY_DEBUG_ADDR_REG 0x1d
|
|
#define AR8051_PHY_DEBUG_DATA_REG 0x1e
|
|
#define AR8051_DEBUG_RGMII_CLK_DLY_REG 0x5
|
|
#define AR8051_RGMII_TX_CLK_DLY 0x100
|
|
|
|
int board_eth_init(struct bd_info *bis)
|
|
{
|
|
int rv, n = 0;
|
|
const char *devname;
|
|
struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
|
|
|
|
rv = handle_mac_address();
|
|
if (rv)
|
|
printf("No MAC address found!\n");
|
|
|
|
writel(RGMII_MODE_ENABLE | RGMII_INT_DELAY, &cdev->miisel);
|
|
|
|
board_phy_init();
|
|
|
|
rv = cpsw_register(&cpsw_data);
|
|
if (rv < 0)
|
|
printf("Error %d registering CPSW switch\n", rv);
|
|
else
|
|
n += rv;
|
|
|
|
/*
|
|
* CPSW RGMII Internal Delay Mode is not supported in all PVT
|
|
* operating points. So we must set the TX clock delay feature
|
|
* in the AR8051 PHY. Since we only support a single ethernet
|
|
* device, we only do this for the first instance.
|
|
*/
|
|
devname = miiphy_get_current_dev();
|
|
|
|
miiphy_write(devname, 0x0, AR8051_PHY_DEBUG_ADDR_REG,
|
|
AR8051_DEBUG_RGMII_CLK_DLY_REG);
|
|
miiphy_write(devname, 0x0, AR8051_PHY_DEBUG_DATA_REG,
|
|
AR8051_RGMII_TX_CLK_DLY);
|
|
return n;
|
|
}
|
|
#endif /* CONFIG_DRIVER_TI_CPSW && !CONFIG_SPL_BUILD */
|