u-boot/drivers/Makefile
Simon Glass 2d424eb0cd spl: Support hash, input, pch, pci, rtc, tpm in SPL
At present these subsystems are only supported in U-Boot proper but it is
sometimes necessary to support them in SPL, or even TPL. Update the
Kconfig and Makefile to support this. Also adjust GPIO so that it can be
used in TPL if required.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2018-11-26 08:25:33 -05:00

116 lines
3.5 KiB
Makefile

# SPDX-License-Identifier: GPL-2.0+
obj-$(CONFIG_$(SPL_TPL_)CLK) += clk/
obj-$(CONFIG_$(SPL_TPL_)DM) += core/
obj-$(CONFIG_$(SPL_TPL_)GPIO_SUPPORT) += gpio/
obj-$(CONFIG_$(SPL_TPL_)DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/
obj-$(CONFIG_$(SPL_TPL_)I2C_SUPPORT) += i2c/
obj-$(CONFIG_$(SPL_TPL_)INPUT) += input/
obj-$(CONFIG_$(SPL_TPL_)LED) += led/
obj-$(CONFIG_$(SPL_TPL_)MMC_SUPPORT) += mmc/
obj-$(CONFIG_$(SPL_TPL_)NAND_SUPPORT) += mtd/nand/raw/
obj-$(CONFIG_$(SPL_TPL_)PCH_SUPPORT) += pch/
obj-$(CONFIG_$(SPL_TPL_)PCI_SUPPORT) += pci/
obj-$(CONFIG_$(SPL_TPL_)PHY) += phy/
obj-$(CONFIG_$(SPL_TPL_)PINCTRL) += pinctrl/
obj-$(CONFIG_$(SPL_TPL_)RAM) += ram/
obj-$(CONFIG_$(SPL_TPL_)RTC_SUPPORT) += rtc/
obj-$(CONFIG_$(SPL_TPL_)SERIAL_SUPPORT) += serial/
obj-$(CONFIG_$(SPL_TPL_)SPI_FLASH_SUPPORT) += mtd/spi/
obj-$(CONFIG_$(SPL_TPL_)SPI_SUPPORT) += spi/
obj-$(CONFIG_$(SPL_TPL_)TIMER) += timer/
obj-$(CONFIG_$(SPL_TPL_)VIRTIO) += virtio/
obj-$(CONFIG_$(SPL_)DM_MAILBOX) += mailbox/
obj-$(CONFIG_$(SPL_)REMOTEPROC) += remoteproc/
obj-$(CONFIG_$(SPL_TPL_)TPM) += tpm/
ifndef CONFIG_TPL_BUILD
ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_SPL_BOOTCOUNT_LIMIT) += bootcount/
obj-$(CONFIG_SPL_CPU_SUPPORT) += cpu/
obj-$(CONFIG_SPL_CRYPTO_SUPPORT) += crypto/
obj-$(CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/
obj-$(CONFIG_ARMADA_38X) += ddr/marvell/a38x/
obj-$(CONFIG_ARMADA_XP) += ddr/marvell/axp/
obj-$(CONFIG_ALTERA_SDRAM) += ddr/altera/
obj-$(CONFIG_SPL_POWER_SUPPORT) += power/ power/pmic/
obj-$(CONFIG_SPL_POWER_SUPPORT) += power/regulator/
obj-$(CONFIG_SPL_POWER_DOMAIN) += power/domain/
obj-$(CONFIG_SPL_DM_RESET) += reset/
obj-$(CONFIG_SPL_MTD_SUPPORT) += mtd/
obj-$(CONFIG_SPL_ONENAND_SUPPORT) += mtd/onenand/
obj-$(CONFIG_SPL_UBI) += mtd/ubispl/
obj-$(CONFIG_SPL_DMA_SUPPORT) += dma/
obj-$(CONFIG_SPL_ETH_SUPPORT) += net/
obj-$(CONFIG_SPL_ETH_SUPPORT) += net/phy/
obj-$(CONFIG_SPL_USB_ETHER) += net/phy/
obj-$(CONFIG_SPL_MUSB_NEW_SUPPORT) += usb/musb-new/
obj-$(CONFIG_SPL_USB_GADGET_SUPPORT) += usb/gadget/
obj-$(CONFIG_SPL_USB_GADGET_SUPPORT) += usb/gadget/udc/
obj-$(CONFIG_SPL_DFU_SUPPORT) += dfu/
obj-$(CONFIG_SPL_WATCHDOG_SUPPORT) += watchdog/
obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += usb/host/
obj-$(CONFIG_OMAP_USB_PHY) += usb/phy/
obj-$(CONFIG_SPL_SATA_SUPPORT) += ata/ scsi/
obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += block/
obj-$(CONFIG_SPL_MMC_SUPPORT) += block/
obj-$(CONFIG_SPL_FPGA_SUPPORT) += fpga/
obj-$(CONFIG_SPL_THERMAL) += thermal/
endif
endif
ifdef CONFIG_TPL_BUILD
obj-$(CONFIG_TPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/
endif
ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_TPL_BUILD),)
obj-y += adc/
obj-y += ata/
obj-$(CONFIG_DM_DEMO) += demo/
obj-$(CONFIG_BIOSEMU) += bios_emulator/
obj-y += block/
obj-y += board/
obj-$(CONFIG_BOOTCOUNT_LIMIT) += bootcount/
obj-$(CONFIG_CPU) += cpu/
obj-y += crypto/
obj-$(CONFIG_FASTBOOT) += fastboot/
obj-y += firmware/
obj-$(CONFIG_FPGA) += fpga/
obj-y += misc/
obj-$(CONFIG_MMC) += mmc/
obj-$(CONFIG_NVME) += nvme/
obj-y += pcmcia/
obj-y += dfu/
obj-$(CONFIG_X86) += pch/
obj-y += phy/allwinner/
obj-y += phy/marvell/
obj-y += rtc/
obj-y += scsi/
obj-y += sound/
obj-y += spmi/
obj-y += sysreset/
obj-y += video/
obj-y += watchdog/
obj-$(CONFIG_QE) += qe/
obj-$(CONFIG_U_QE) += qe/
obj-y += mailbox/
obj-y += memory/
obj-y += pwm/
obj-y += reset/
obj-y += input/
# SOC specific infrastructure drivers.
obj-y += smem/
obj-y += soc/
obj-y += thermal/
obj-$(CONFIG_TEE) += tee/
obj-y += axi/
obj-$(CONFIG_W1) += w1/
obj-$(CONFIG_W1_EEPROM) += w1-eeprom/
obj-$(CONFIG_MACH_PIC32) += ddr/microchip/
endif