mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-22 11:13:07 +00:00
86cf1c8285
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
217 lines
7.3 KiB
C
217 lines
7.3 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* ti_armv7_common.h
|
|
*
|
|
* Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
|
|
*
|
|
* The various ARMv7 SoCs from TI all share a number of IP blocks when
|
|
* implementing a given feature. Rather than define these in every
|
|
* board or even SoC common file, we define a common file to be re-used
|
|
* in all cases. While technically true that some of these details are
|
|
* configurable at the board design, they are common throughout SoC
|
|
* reference platforms as well as custom designs and become de facto
|
|
* standards.
|
|
*/
|
|
|
|
#ifndef __CONFIG_TI_ARMV7_COMMON_H__
|
|
#define __CONFIG_TI_ARMV7_COMMON_H__
|
|
|
|
/* Support both device trees and ATAGs. */
|
|
#define CONFIG_CMDLINE_TAG
|
|
#define CONFIG_SETUP_MEMORY_TAGS
|
|
#define CONFIG_INITRD_TAG
|
|
|
|
/*
|
|
* Our DDR memory always starts at 0x80000000 and U-Boot shall have
|
|
* relocated itself to higher in memory by the time this value is used.
|
|
* However, set this to a 32MB offset to allow for easier Linux kernel
|
|
* booting as the default is often used as the kernel load address.
|
|
*/
|
|
#define CONFIG_SYS_LOAD_ADDR 0x82000000
|
|
|
|
/*
|
|
* We setup defaults based on constraints from the Linux kernel, which should
|
|
* also be safe elsewhere. We have the default load at 32MB into DDR (for
|
|
* the kernel), FDT above 128MB (the maximum location for the end of the
|
|
* kernel), and the ramdisk 512KB above that (allowing for hopefully never
|
|
* seen large trees). We say all of this must be within the first 256MB
|
|
* as that will normally be within the kernel lowmem and thus visible via
|
|
* bootm_size and we only run on platforms with 256MB or more of memory.
|
|
*/
|
|
#define DEFAULT_LINUX_BOOT_ENV \
|
|
"loadaddr=0x82000000\0" \
|
|
"kernel_addr_r=0x82000000\0" \
|
|
"fdtaddr=0x88000000\0" \
|
|
"fdt_addr_r=0x88000000\0" \
|
|
"rdaddr=0x88080000\0" \
|
|
"ramdisk_addr_r=0x88080000\0" \
|
|
"scriptaddr=0x80000000\0" \
|
|
"pxefile_addr_r=0x80100000\0" \
|
|
"bootm_size=0x10000000\0" \
|
|
"boot_fdt=try\0"
|
|
|
|
#define DEFAULT_FIT_TI_ARGS \
|
|
"boot_fit=0\0" \
|
|
"fit_loadaddr=0x87000000\0" \
|
|
"fit_bootfile=fitImage\0" \
|
|
"update_to_fit=setenv loadaddr ${fit_loadaddr}; setenv bootfile ${fit_bootfile}\0" \
|
|
"loadfit=run args_mmc; bootm ${loadaddr}#${fdtfile};\0" \
|
|
|
|
/*
|
|
* DDR information. If the CONFIG_NR_DRAM_BANKS is not defined,
|
|
* we say (for simplicity) that we have 1 bank, always, even when
|
|
* we have more. We always start at 0x80000000, and we place the
|
|
* initial stack pointer in our SRAM. Otherwise, we can define
|
|
* CONFIG_NR_DRAM_BANKS before including this file.
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x80000000
|
|
|
|
#ifndef CONFIG_SYS_INIT_SP_ADDR
|
|
#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \
|
|
GENERATED_GBL_DATA_SIZE)
|
|
#endif
|
|
|
|
/* Timer information. */
|
|
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
|
|
|
|
/*
|
|
* Disable DM_* for SPL build and can be re-enabled after adding
|
|
* DM support in SPL
|
|
*/
|
|
#ifdef CONFIG_SPL_BUILD
|
|
#undef CONFIG_DM_I2C
|
|
#endif
|
|
|
|
/* I2C IP block */
|
|
#define CONFIG_I2C
|
|
#ifndef CONFIG_DM_I2C
|
|
#define CONFIG_SYS_I2C
|
|
#else
|
|
/*
|
|
* Enable CONFIG_DM_I2C_COMPAT temporarily until all the i2c client
|
|
* devices are adopted to DM
|
|
*/
|
|
#define CONFIG_DM_I2C_COMPAT
|
|
#endif
|
|
|
|
/*
|
|
* The following are general good-enough settings for U-Boot. We set a
|
|
* large malloc pool as we generally have a lot of DDR, and we opt for
|
|
* function over binary size in the main portion of U-Boot as this is
|
|
* generally easily constrained later if needed. We enable the config
|
|
* options that give us information in the environment about what board
|
|
* we are on so we do not need to rely on the command prompt. We set a
|
|
* console baudrate of 115200 and use the default baud rate table.
|
|
*/
|
|
#define CONFIG_SYS_MALLOC_LEN SZ_32M
|
|
#define CONFIG_ENV_OVERWRITE /* Overwrite ethaddr / serial# */
|
|
|
|
/* As stated above, the following choices are optional. */
|
|
|
|
/* We set the max number of command args high to avoid HUSH bugs. */
|
|
#define CONFIG_SYS_MAXARGS 64
|
|
|
|
/* Console I/O Buffer Size */
|
|
#define CONFIG_SYS_CBSIZE 1024
|
|
/* Boot Argument Buffer Size */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
|
|
|
|
/*
|
|
* When we have SPI, NOR or NAND flash we expect to be making use of
|
|
* mtdparts, both for ease of use in U-Boot and for passing information
|
|
* on to the Linux kernel.
|
|
*/
|
|
|
|
/*
|
|
* Our platforms make use of SPL to initalize the hardware (primarily
|
|
* memory) enough for full U-Boot to be loaded. We make use of the general
|
|
* SPL framework found under common/spl/. Given our generally common memory
|
|
* map, we set a number of related defaults and sizes here.
|
|
*/
|
|
#if !defined(CONFIG_NOR_BOOT) && \
|
|
!(defined(CONFIG_QSPI_BOOT) && defined(CONFIG_AM43XX))
|
|
|
|
/*
|
|
* We also support Falcon Mode so that the Linux kernel can be booted
|
|
* directly from SPL. This is not currently available on HS devices.
|
|
*/
|
|
|
|
/*
|
|
* Place the image at the start of the ROM defined image space (per
|
|
* CONFIG_SPL_TEXT_BASE and we limit our size to the ROM-defined
|
|
* downloaded image area minus 1KiB for scratch space. We initalize DRAM as
|
|
* soon as we can so that we can place stack, malloc and BSS there. We load
|
|
* U-Boot itself into memory at 0x80800000 for legacy reasons (to not conflict
|
|
* with older SPLs). We have our BSS be placed 2MiB after this, to allow for
|
|
* the default Linux kernel address of 0x80008000 to work with most sized
|
|
* kernels, in the Falcon Mode case. We have the SPL malloc pool at the end
|
|
* of the BSS area. We suggest that the stack be placed at 32MiB after the
|
|
* start of DRAM to allow room for all of the above (handled in Kconfig).
|
|
*/
|
|
#ifndef CONFIG_SPL_BSS_START_ADDR
|
|
#define CONFIG_SPL_BSS_START_ADDR 0x80a00000
|
|
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
|
|
#endif
|
|
#ifndef CONFIG_SYS_SPL_MALLOC_START
|
|
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
|
|
CONFIG_SPL_BSS_MAX_SIZE)
|
|
#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_8M
|
|
#endif
|
|
#ifndef CONFIG_SPL_MAX_SIZE
|
|
#define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \
|
|
CONFIG_SPL_TEXT_BASE)
|
|
#endif
|
|
|
|
|
|
/* FAT sd card locations. */
|
|
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
|
|
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
|
|
|
|
#ifdef CONFIG_SPL_OS_BOOT
|
|
/* FAT */
|
|
#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
|
|
#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"
|
|
|
|
/* RAW SD card / eMMC */
|
|
#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1700 /* address 0x2E0000 */
|
|
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x1500 /* address 0x2A0000 */
|
|
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x200 /* 256KiB */
|
|
#endif
|
|
|
|
/* General parts of the framework, required. */
|
|
|
|
#ifdef CONFIG_NAND
|
|
#define CONFIG_SPL_NAND_BASE
|
|
#define CONFIG_SPL_NAND_DRIVERS
|
|
#define CONFIG_SPL_NAND_ECC
|
|
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
|
|
#endif
|
|
#endif /* !CONFIG_NOR_BOOT */
|
|
|
|
/* Generic Environment Variables */
|
|
|
|
#ifdef CONFIG_CMD_NET
|
|
#define NETARGS \
|
|
"static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
|
|
"::off\0" \
|
|
"nfsopts=nolock\0" \
|
|
"rootpath=/export/rootfs\0" \
|
|
"netloadimage=tftp ${loadaddr} ${bootfile}\0" \
|
|
"netloadfdt=tftp ${fdtaddr} ${fdtfile}\0" \
|
|
"netargs=setenv bootargs console=${console} " \
|
|
"${optargs} " \
|
|
"root=/dev/nfs " \
|
|
"nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
|
|
"ip=dhcp\0" \
|
|
"netboot=echo Booting from network ...; " \
|
|
"setenv autoload no; " \
|
|
"dhcp; " \
|
|
"run netloadimage; " \
|
|
"run netloadfdt; " \
|
|
"run netargs; " \
|
|
"bootz ${loadaddr} - ${fdtaddr}\0"
|
|
#else
|
|
#define NETARGS ""
|
|
#endif
|
|
|
|
#endif /* __CONFIG_TI_ARMV7_COMMON_H__ */
|