mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-22 11:13:07 +00:00
2fe88d4522
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
272 lines
8.6 KiB
C
272 lines
8.6 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright (C) 2011-2014 OMICRON electronics GmbH
|
|
*
|
|
* Based on da850evm.h. Original Copyrights follow:
|
|
*
|
|
* Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
|
|
* Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* Board
|
|
*/
|
|
#define CONFIG_MACH_TYPE MACH_TYPE_CALIMAIN
|
|
|
|
/*
|
|
* SoC Configuration
|
|
*/
|
|
#define CONFIG_SYS_EXCEPTION_VECTORS_HIGH
|
|
#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID)
|
|
#define CONFIG_SYS_OSCIN_FREQ calimain_get_osc_freq()
|
|
#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE
|
|
#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
|
|
#define CONFIG_ARCH_CPU_INIT
|
|
#define CONFIG_HW_WATCHDOG
|
|
#define CONFIG_SYS_WDTTIMERBASE DAVINCI_TIMER1_BASE
|
|
#define CONFIG_SYS_WDT_PERIOD_LOW \
|
|
(60 * CONFIG_SYS_OSCIN_FREQ) /* 60 s heartbeat */
|
|
#define CONFIG_SYS_WDT_PERIOD_HIGH 0x0
|
|
#define CONFIG_SYS_DV_NOR_BOOT_CFG (0x11)
|
|
|
|
/*
|
|
* PLL configuration
|
|
*/
|
|
|
|
#define CONFIG_SYS_DA850_PLL0_PLLM \
|
|
((calimain_get_osc_freq() == 25000000) ? 23 : 24)
|
|
#define CONFIG_SYS_DA850_PLL1_PLLM \
|
|
((calimain_get_osc_freq() == 25000000) ? 20 : 21)
|
|
|
|
/*
|
|
* DDR2 memory configuration
|
|
*/
|
|
#define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
|
|
DV_DDR_PHY_EXT_STRBEN | \
|
|
(0x4 << DV_DDR_PHY_RD_LATENCY_SHIFT))
|
|
|
|
#define CONFIG_SYS_DA850_DDR2_SDBCR ( \
|
|
(1 << DV_DDR_SDCR_DDR2EN_SHIFT) | \
|
|
(1 << DV_DDR_SDCR_DDRDRIVE0_SHIFT) | \
|
|
(1 << DV_DDR_SDCR_DDREN_SHIFT) | \
|
|
(1 << DV_DDR_SDCR_SDRAMEN_SHIFT) | \
|
|
(1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) | \
|
|
(0x3 << DV_DDR_SDCR_CL_SHIFT) | \
|
|
(0x3 << DV_DDR_SDCR_IBANK_SHIFT) | \
|
|
(0x2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
|
|
|
|
/* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */
|
|
#define CONFIG_SYS_DA850_DDR2_SDBCR2 0
|
|
|
|
#define CONFIG_SYS_DA850_DDR2_SDTIMR ( \
|
|
(16 << DV_DDR_SDTMR1_RFC_SHIFT) | \
|
|
(1 << DV_DDR_SDTMR1_RP_SHIFT) | \
|
|
(1 << DV_DDR_SDTMR1_RCD_SHIFT) | \
|
|
(1 << DV_DDR_SDTMR1_WR_SHIFT) | \
|
|
(5 << DV_DDR_SDTMR1_RAS_SHIFT) | \
|
|
(7 << DV_DDR_SDTMR1_RC_SHIFT) | \
|
|
(1 << DV_DDR_SDTMR1_RRD_SHIFT) | \
|
|
(1 << DV_DDR_SDTMR1_WTR_SHIFT))
|
|
|
|
#define CONFIG_SYS_DA850_DDR2_SDTIMR2 ( \
|
|
(7 << DV_DDR_SDTMR2_RASMAX_SHIFT) | \
|
|
(2 << DV_DDR_SDTMR2_XP_SHIFT) | \
|
|
(0 << DV_DDR_SDTMR2_ODT_SHIFT) | \
|
|
(18 << DV_DDR_SDTMR2_XSNR_SHIFT) | \
|
|
(199 << DV_DDR_SDTMR2_XSRD_SHIFT) | \
|
|
(0 << DV_DDR_SDTMR2_RTP_SHIFT) | \
|
|
(2 << DV_DDR_SDTMR2_CKE_SHIFT))
|
|
|
|
#define CONFIG_SYS_DA850_DDR2_SDRCR 0x000003FF
|
|
#define CONFIG_SYS_DA850_DDR2_PBBPR 0x30
|
|
|
|
/*
|
|
* Flash memory timing
|
|
*/
|
|
|
|
#define CONFIG_SYS_DA850_CS2CFG ( \
|
|
DAVINCI_ABCR_WSETUP(2) | \
|
|
DAVINCI_ABCR_WSTROBE(5) | \
|
|
DAVINCI_ABCR_WHOLD(3) | \
|
|
DAVINCI_ABCR_RSETUP(1) | \
|
|
DAVINCI_ABCR_RSTROBE(14) | \
|
|
DAVINCI_ABCR_RHOLD(0) | \
|
|
DAVINCI_ABCR_TA(3) | \
|
|
DAVINCI_ABCR_ASIZE_16BIT)
|
|
|
|
/* single 64 MB NOR flash device connected to CS2 and CS3 */
|
|
#define CONFIG_SYS_DA850_CS3CFG CONFIG_SYS_DA850_CS2CFG
|
|
|
|
/*
|
|
* Memory Info
|
|
*/
|
|
#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */
|
|
#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
|
|
#define PHYS_SDRAM_1_SIZE (128 << 20) /* SDRAM size 128MB */
|
|
#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
|
|
|
|
#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \
|
|
DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \
|
|
DAVINCI_SYSCFG_SUSPSRC_SPI1 | \
|
|
DAVINCI_SYSCFG_SUSPSRC_UART2 | \
|
|
DAVINCI_SYSCFG_SUSPSRC_EMAC | \
|
|
DAVINCI_SYSCFG_SUSPSRC_I2C)
|
|
|
|
/* memtest start addr */
|
|
#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000)
|
|
|
|
/* memtest will be run on 16MB */
|
|
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (16 << 20))
|
|
|
|
/*
|
|
* Serial Driver info
|
|
*/
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */
|
|
#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */
|
|
#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */
|
|
#define CONFIG_SYS_FLASH_SECT_SZ (128 << 10) /* 128KB */
|
|
#define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
|
|
#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ
|
|
#define CONFIG_ENV_ADDR \
|
|
(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SECT_SZ * 2)
|
|
#define CONFIG_ENV_SIZE (128 << 10)
|
|
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
|
|
#define PHYS_FLASH_SIZE (64 << 20) /* Flash size 64MB */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT \
|
|
((PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ) + 3)
|
|
|
|
/*
|
|
* Network & Ethernet Configuration
|
|
*/
|
|
#ifdef CONFIG_DRIVER_TI_EMAC
|
|
#define CONFIG_BOOTP_DNS2
|
|
#define CONFIG_BOOTP_SEND_HOSTNAME
|
|
#define CONFIG_NET_RETRY_COUNT 10
|
|
#endif
|
|
|
|
/*
|
|
* U-Boot general configuration
|
|
*/
|
|
#define CONFIG_BOOTFILE "uImage" /* Boot file name */
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
|
|
#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000)
|
|
#define CONFIG_LOADADDR 0xc0700000
|
|
#define CONFIG_MX_CYCLIC
|
|
|
|
/*
|
|
* Linux Information
|
|
*/
|
|
#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100)
|
|
#define CONFIG_CMDLINE_TAG
|
|
#define CONFIG_REVISION_TAG
|
|
#define CONFIG_SETUP_MEMORY_TAGS
|
|
#define CONFIG_BOOTCOMMAND "run checkupdate; run checkbutton;"
|
|
#define CONFIG_BOOT_RETRY_TIME 60 /* continue boot after 60 s inactivity */
|
|
#define CONFIG_RESET_TO_RETRY
|
|
|
|
/*
|
|
* Default environment settings
|
|
* gpio0 = button, gpio1 = led green, gpio2 = led red
|
|
* verify = n ... disable kernel checksum verification for faster booting
|
|
*/
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"tftpdir=calimero\0" \
|
|
"flashkernel=tftpboot $loadaddr $tftpdir/uImage; " \
|
|
"erase 0x60800000 +0x400000; " \
|
|
"cp.b $loadaddr 0x60800000 $filesize\0" \
|
|
"flashrootfs=" \
|
|
"tftpboot $loadaddr $tftpdir/rootfs.jffs2; " \
|
|
"erase 0x60c00000 +0x2e00000; " \
|
|
"cp.b $loadaddr 0x60c00000 $filesize\0" \
|
|
"flashuboot=tftpboot $loadaddr $tftpdir/u-boot.bin; " \
|
|
"protect off all; " \
|
|
"erase 0x60000000 +0x80000; " \
|
|
"cp.b $loadaddr 0x60000000 $filesize\0" \
|
|
"flashrlk=tftpboot $loadaddr $tftpdir/uImage-rlk; " \
|
|
"erase 0x60080000 +0x780000; " \
|
|
"cp.b $loadaddr 0x60080000 $filesize\0" \
|
|
"erase_persistent=erase 0x63a00000 +0x600000;\0" \
|
|
"bootnor=setenv bootargs console=ttyS2,115200n8 " \
|
|
"root=/dev/mtdblock3 rw rootfstype=jffs2 " \
|
|
"rootwait ethaddr=$ethaddr; " \
|
|
"gpio c 1; gpio s 2; bootm 0x60800000\0" \
|
|
"bootrlk=gpio s 1; gpio s 2;" \
|
|
"setenv bootargs console=ttyS2,115200n8 " \
|
|
"ethaddr=$ethaddr; bootm 0x60080000\0" \
|
|
"boottftp=setenv bootargs console=ttyS2,115200n8 " \
|
|
"root=/dev/mtdblock3 rw rootfstype=jffs2 " \
|
|
"rootwait ethaddr=$ethaddr; " \
|
|
"tftpboot $loadaddr $tftpdir/uImage;" \
|
|
"gpio c 1; gpio s 2; bootm $loadaddr\0" \
|
|
"checkupdate=if test -n $update_flag; then " \
|
|
"echo Previous update failed - starting RLK; " \
|
|
"run bootrlk; fi; " \
|
|
"if test -n $initial_setup; then " \
|
|
"echo Running initial setup procedure; " \
|
|
"sleep 1; run flashall; fi\0" \
|
|
"product=accessory\0" \
|
|
"serial=XX12345\0" \
|
|
"checknor=" \
|
|
"if gpio i 0; then run bootnor; fi;\0" \
|
|
"checkrlk=" \
|
|
"if gpio i 0; then run bootrlk; fi;\0" \
|
|
"checkbutton=" \
|
|
"run checknor; sleep 1;" \
|
|
"run checknor; sleep 1;" \
|
|
"run checknor; sleep 1;" \
|
|
"run checknor; sleep 1;" \
|
|
"run checknor;" \
|
|
"gpio s 1; gpio s 2;" \
|
|
"echo ---- Release button to boot RLK ----;" \
|
|
"run checkrlk; sleep 1;" \
|
|
"run checkrlk; sleep 1;" \
|
|
"run checkrlk; sleep 1;" \
|
|
"run checkrlk; sleep 1;" \
|
|
"run checkrlk; sleep 1;" \
|
|
"run checkrlk;" \
|
|
"echo ---- Factory reset requested ----;" \
|
|
"gpio c 1;" \
|
|
"setenv factory_reset true;" \
|
|
"saveenv;" \
|
|
"run bootnor;\0" \
|
|
"flashall=run flashrlk;" \
|
|
"run flashkernel;" \
|
|
"run flashrootfs;" \
|
|
"setenv erase_datafs true;" \
|
|
"setenv initial_setup;" \
|
|
"saveenv;" \
|
|
"run bootnor;\0" \
|
|
"verify=n\0" \
|
|
"clearenv=protect off all;" \
|
|
"erase 0x60040000 +0x40000;\0" \
|
|
"altbootcmd=run bootrlk\0"
|
|
|
|
#define CONFIG_PREBOOT \
|
|
"echo Version: $ver; " \
|
|
"echo Serial: $serial; " \
|
|
"echo MAC: $ethaddr; " \
|
|
"echo Product: $product; " \
|
|
"gpio c 1; gpio c 2;"
|
|
|
|
/* additions for new relocation code, must added to all boards */
|
|
#define CONFIG_SYS_SDRAM_BASE 0xc0000000
|
|
/* initial stack pointer in internal SRAM */
|
|
#define CONFIG_SYS_INIT_SP_ADDR (0x8001ff00)
|
|
|
|
#define CONFIG_SYS_BOOTCOUNT_LE /* Use little-endian accessors */
|
|
|
|
#ifndef __ASSEMBLY__
|
|
int calimain_get_osc_freq(void);
|
|
#endif
|
|
|
|
#include <asm/arch/hardware.h>
|
|
|
|
#endif /* __CONFIG_H */
|