mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-24 20:13:39 +00:00
83d290c56f
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
160 lines
3.6 KiB
C
160 lines
3.6 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* (C) Copyright 2009
|
|
* Net Insight <www.netinsight.net>
|
|
* Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
|
|
*
|
|
* Based on sheevaplug.c:
|
|
* (C) Copyright 2009
|
|
* Marvell Semiconductor <www.marvell.com>
|
|
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <miiphy.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
#include <asm/arch/mpp.h>
|
|
#include "openrd.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/*
|
|
* default gpio configuration
|
|
* There are maximum 64 gpios controlled through 2 sets of registers
|
|
* the below configuration configures mainly initial LED status
|
|
*/
|
|
mvebu_config_gpio(OPENRD_OE_VAL_LOW,
|
|
OPENRD_OE_VAL_HIGH,
|
|
OPENRD_OE_LOW, OPENRD_OE_HIGH);
|
|
|
|
/* Multi-Purpose Pins Functionality configuration */
|
|
static const u32 kwmpp_config[] = {
|
|
MPP0_NF_IO2,
|
|
MPP1_NF_IO3,
|
|
MPP2_NF_IO4,
|
|
MPP3_NF_IO5,
|
|
MPP4_NF_IO6,
|
|
MPP5_NF_IO7,
|
|
MPP6_SYSRST_OUTn,
|
|
MPP7_GPO,
|
|
MPP8_TW_SDA,
|
|
MPP9_TW_SCK,
|
|
MPP10_UART0_TXD,
|
|
MPP11_UART0_RXD,
|
|
MPP12_SD_CLK,
|
|
MPP13_SD_CMD, /* Alt UART1_TXD */
|
|
MPP14_SD_D0, /* Alt UART1_RXD */
|
|
MPP15_SD_D1,
|
|
MPP16_SD_D2,
|
|
MPP17_SD_D3,
|
|
MPP18_NF_IO0,
|
|
MPP19_NF_IO1,
|
|
MPP20_GE1_0,
|
|
MPP21_GE1_1,
|
|
MPP22_GE1_2,
|
|
MPP23_GE1_3,
|
|
MPP24_GE1_4,
|
|
MPP25_GE1_5,
|
|
MPP26_GE1_6,
|
|
MPP27_GE1_7,
|
|
MPP28_GPIO,
|
|
MPP29_TSMP9,
|
|
MPP30_GE1_10,
|
|
MPP31_GE1_11,
|
|
MPP32_GE1_12,
|
|
MPP33_GE1_13,
|
|
MPP34_GPIO, /* UART1 / SD sel */
|
|
MPP35_TDM_CH0_TX_QL,
|
|
MPP36_TDM_SPI_CS1,
|
|
MPP37_TDM_CH2_TX_QL,
|
|
MPP38_TDM_CH2_RX_QL,
|
|
MPP39_AUDIO_I2SBCLK,
|
|
MPP40_AUDIO_I2SDO,
|
|
MPP41_AUDIO_I2SLRC,
|
|
MPP42_AUDIO_I2SMCLK,
|
|
MPP43_AUDIO_I2SDI,
|
|
MPP44_AUDIO_EXTCLK,
|
|
MPP45_TDM_PCLK,
|
|
MPP46_TDM_FS,
|
|
MPP47_TDM_DRX,
|
|
MPP48_TDM_DTX,
|
|
MPP49_TDM_CH0_RX_QL,
|
|
0
|
|
};
|
|
|
|
kirkwood_mpp_conf(kwmpp_config, NULL);
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/*
|
|
* arch number of board
|
|
*/
|
|
#if defined(CONFIG_BOARD_IS_OPENRD_BASE)
|
|
gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE;
|
|
#elif defined(CONFIG_BOARD_IS_OPENRD_CLIENT)
|
|
gd->bd->bi_arch_number = MACH_TYPE_OPENRD_CLIENT;
|
|
#elif defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE)
|
|
gd->bd->bi_arch_number = MACH_TYPE_OPENRD_ULTIMATE;
|
|
#endif
|
|
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_RESET_PHY_R
|
|
/* Configure and enable MV88E1116/88E1121 PHY */
|
|
void mv_phy_init(char *name)
|
|
{
|
|
u16 reg;
|
|
u16 devadr;
|
|
|
|
if (miiphy_set_current_dev(name))
|
|
return;
|
|
|
|
/* command to read PHY dev address */
|
|
if (miiphy_read(name, 0xEE, 0xEE, (u16 *)&devadr)) {
|
|
printf("Err..%s could not read PHY dev address\n", __func__);
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Enable RGMII delay on Tx and Rx for CPU port
|
|
* Ref: sec 4.7.2 of chip datasheet
|
|
*/
|
|
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
|
|
miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
|
|
reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
|
|
miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
|
|
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
|
|
|
|
/* reset the phy */
|
|
miiphy_reset(name, devadr);
|
|
|
|
printf(PHY_NO" Initialized on %s\n", name);
|
|
}
|
|
|
|
void reset_phy(void)
|
|
{
|
|
mv_phy_init("egiga0");
|
|
|
|
#ifdef CONFIG_BOARD_IS_OPENRD_CLIENT
|
|
/* Kirkwood ethernet driver is written with the assumption that in case
|
|
* of multiple PHYs, their addresses are consecutive. But unfortunately
|
|
* in case of OpenRD-Client, PHY addresses are not consecutive.*/
|
|
miiphy_write("egiga1", 0xEE, 0xEE, 24);
|
|
#endif
|
|
|
|
#if defined(CONFIG_BOARD_IS_OPENRD_CLIENT) || \
|
|
defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE)
|
|
/* configure and initialize both PHY's */
|
|
mv_phy_init("egiga1");
|
|
#endif
|
|
}
|
|
#endif /* CONFIG_RESET_PHY_R */
|