mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-25 04:23:46 +00:00
cf35290258
This patch is used to support DBD owner fuse changed to S400 only. The XRDC PDAC2 for LPAV pbridge5 and MSC1/2/3 for GPIO and LPAV are not configured by S400 default setting. So these PDAC and MSC are invalid, only DBD owner can access the corresponding resources. We have to configure necessary PDAC and MSC for SPL before DDR initialization. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
138 lines
2.7 KiB
C
138 lines
2.7 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright 2021 NXP
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <init.h>
|
|
#include <spl.h>
|
|
#include <asm/io.h>
|
|
#include <errno.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/imx8ulp-pins.h>
|
|
#include <dm/uclass.h>
|
|
#include <dm/device.h>
|
|
#include <dm/uclass-internal.h>
|
|
#include <dm/device-internal.h>
|
|
#include <dm/lists.h>
|
|
#include <asm/arch/ddr.h>
|
|
#include <asm/arch/rdc.h>
|
|
#include <asm/arch/upower.h>
|
|
#include <asm/mach-imx/s400_api.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
void spl_dram_init(void)
|
|
{
|
|
/* Reboot in dual boot setting no need to init ddr again */
|
|
bool ddr_enable = pcc_clock_is_enable(5, LPDDR4_PCC5_SLOT);
|
|
|
|
if (!ddr_enable) {
|
|
init_clk_ddr();
|
|
ddr_init(&dram_timing);
|
|
} else {
|
|
/* reinit pfd/pfddiv and lpavnic except pll4*/
|
|
cgc2_pll4_init(false);
|
|
}
|
|
}
|
|
|
|
u32 spl_boot_device(void)
|
|
{
|
|
return BOOT_DEVICE_BOOTROM;
|
|
}
|
|
|
|
int power_init_board(void)
|
|
{
|
|
if (IS_ENABLED(CONFIG_IMX8ULP_LD_MODE)) {
|
|
/* Set buck3 to 0.9v LD */
|
|
upower_pmic_i2c_write(0x22, 0x18);
|
|
} else if (IS_ENABLED(CONFIG_IMX8ULP_ND_MODE)) {
|
|
/* Set buck3 to 1.0v ND */
|
|
upower_pmic_i2c_write(0x22, 0x20);
|
|
} else {
|
|
/* Set buck3 to 1.1v OD */
|
|
upower_pmic_i2c_write(0x22, 0x28);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
void display_ele_fw_version(void)
|
|
{
|
|
u32 fw_version, sha1, res;
|
|
int ret;
|
|
|
|
ret = ahab_get_fw_version(&fw_version, &sha1, &res);
|
|
if (ret) {
|
|
printf("ahab get firmware version failed %d, 0x%x\n", ret, res);
|
|
} else {
|
|
printf("ELE firmware version %u.%u.%u-%x",
|
|
(fw_version & (0x00ff0000)) >> 16,
|
|
(fw_version & (0x0000ff00)) >> 8,
|
|
(fw_version & (0x000000ff)), sha1);
|
|
((fw_version & (0x80000000)) >> 31) == 1 ? puts("-dirty\n") : puts("\n");
|
|
}
|
|
}
|
|
|
|
void spl_board_init(void)
|
|
{
|
|
u32 res;
|
|
int ret;
|
|
|
|
ret = imx8ulp_dm_post_init();
|
|
if (ret)
|
|
return;
|
|
|
|
board_early_init_f();
|
|
|
|
preloader_console_init();
|
|
|
|
puts("Normal Boot\n");
|
|
|
|
display_ele_fw_version();
|
|
|
|
/* After AP set iomuxc0, the i2c can't work, Need M33 to set it now */
|
|
|
|
/* Load the lposc fuse to work around ROM issue. The fuse depends on S400 to read. */
|
|
if (is_soc_rev(CHIP_REV_1_0))
|
|
load_lposc_fuse();
|
|
|
|
upower_init();
|
|
|
|
power_init_board();
|
|
|
|
clock_init_late();
|
|
|
|
/* This must place after upower init, so access to MDA and MRC are valid */
|
|
/* Init XRDC MDA */
|
|
xrdc_init_mda();
|
|
|
|
/* Init XRDC MRC for VIDEO, DSP domains */
|
|
xrdc_init_mrc();
|
|
|
|
xrdc_init_pdac_msc();
|
|
|
|
/* DDR initialization */
|
|
spl_dram_init();
|
|
|
|
/* Call it after PS16 power up */
|
|
set_lpav_qos();
|
|
|
|
/* Enable A35 access to the CAAM */
|
|
ret = ahab_release_caam(0x7, &res);
|
|
if (ret)
|
|
printf("ahab release caam failed %d, 0x%x\n", ret, res);
|
|
}
|
|
|
|
void board_init_f(ulong dummy)
|
|
{
|
|
/* Clear the BSS. */
|
|
memset(__bss_start, 0, __bss_end - __bss_start);
|
|
|
|
timer_init();
|
|
|
|
arch_cpu_init();
|
|
|
|
board_init_r(NULL, 0);
|
|
}
|