mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-16 17:58:23 +00:00
2226ca1734
Now that proper load and execution addresses are set in v1 kwbimage we can use it for loading and booting U-Boot proper. Use the new spl_parse_board_header() function to implement parsing the kwbimage v1 header. Use information from this header to locate offset and size of the U-Boot proper binary, instead of using the legacy U-Boot header which is prepended to the U-Boot proper binary stored at fixed offset. This has the advantage that we do not need to relay on legacy U-Boot header anymore and therefore U-Boot proper binary can be stored at any offset, as is the case when loading & booting U-Boot proper by BootROM. The CONFIG_SYS_U_BOOT_OFFS option is therefore not used by SPL code anymore. Also allow to compile U-Boot SPL without CONFIG_SPL_SPI_FLASH_SUPPORT, CONFIG_SPL_MMC_SUPPORT or CONFIG_SPL_SATA_SUPPORT set. In this case BootROM is used for loading and executing U-Boot proper. This reduces the size of U-Boot's SPL image. By default these config options are enabled and so BootROM loading is not used. In some cases BootROM reads from SPI NOR at lower speed than U-Boot SPL. So people can decide whether they want to have smaller SPL binary at the cost of slower boot. Therefore dependency on CONFIG_SPL_DM_SPI, CONFIG_SPL_SPI_FLASH_SUPPORT, CONFIG_SPL_SPI_LOAD, CONFIG_SPL_SPI_SUPPORT, CONFIG_SPL_DM_GPIO, CONFIG_SPL_DM_MMC, CONFIG_SPL_GPIO_SUPPORT, CONFIG_SPL_LIBDISK_SUPPORT, CONFIG_SPL_MMC_SUPPORT, CONFIG_SPL_SATA_SUPPORT and CONFIG_SPL_LIBDISK_SUPPORT is changed from strict to related "imply" (which can be selectivelly turned off and causes booting via BootROM). Options CONFIG_SYS_SPI_U_BOOT_OFFS, CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR and CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET have to to be set to zero as they define the location where kwbimage header starts. It is the location where BootROM expects start of the kwbimage from which it reads, parses and executes SPL part. The same applies to option CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR, which has to be set to one. Update all config files to set correct values of these options and set CONFIG_SYS_U_BOOT_OFFS to the correct value - the offset where U-Boot proper starts. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
57 lines
2 KiB
Text
57 lines
2 KiB
Text
menu "ClearFog configuration"
|
|
depends on TARGET_CLEARFOG
|
|
|
|
config TARGET_CLEARFOG_BASE
|
|
bool "Use ClearFog Base static configuration"
|
|
help
|
|
Use the ClearFog Base as the static configuration instead of the
|
|
default which uses the ClearFog Pro.
|
|
|
|
Runtime board detection is always attempted and used if available. The
|
|
static configuration is used as a fallback in cases where runtime
|
|
detection is disabled, is not available in hardware, or otherwise fails.
|
|
|
|
Only newer revisions of the ClearFog product line support runtime
|
|
detection via additional EEPROM hardware. This option enables selecting
|
|
the Base variant for older hardware revisions.
|
|
|
|
config CLEARFOG_CON3_SATA
|
|
bool "Use CON3 slot in SATA mode"
|
|
help
|
|
Use the CON3 port with SATA protocol instead of the default PCIe.
|
|
The ClearFog port allows usage of either mSATA or miniPCIe
|
|
modules, but the desired protocol must be configured at build
|
|
time since it affects the SerDes topology layout.
|
|
|
|
config CLEARFOG_CON2_SATA
|
|
bool "Use CON2 slot in SATA mode"
|
|
depends on !TARGET_CLEARFOG_BASE
|
|
help
|
|
Use the CON2 port with SATA protocol instead of the default PCIe.
|
|
The ClearFog port allows usage of either mSATA or miniPCIe
|
|
modules, but the desired protocol must be configured at build
|
|
time since it affects the SerDes topology layout.
|
|
|
|
config CLEARFOG_SFP_25GB
|
|
bool "Enable 2.5 Gbps mode for SFP"
|
|
help
|
|
Set the SFP module connection to support 2.5 Gbps transfer speed for the
|
|
SGMII connection (requires a supporting SFP). By default, transfer speed
|
|
of 1.25 Gbps is used, suitable for a more common 1 Gbps SFP module.
|
|
|
|
config ENV_SIZE
|
|
hex "Environment Size"
|
|
default 0x10000
|
|
|
|
config ENV_OFFSET
|
|
hex "Environment offset"
|
|
default 0xF0000
|
|
|
|
config ENV_SECT_SIZE
|
|
hex "Environment Sector-Size"
|
|
# Use SPI flash erase block size of 4 KiB
|
|
default 0x1000 if MVEBU_SPL_BOOT_DEVICE_SPI || MVEBU_SPL_BOOT_DEVICE_SATA
|
|
# Use optimistic 64 KiB erase block, will vary between actual media
|
|
default 0x10000 if MVEBU_SPL_BOOT_DEVICE_MMC || MVEBU_SPL_BOOT_DEVICE_UART
|
|
|
|
endmenu
|