u-boot/configs/ls1021atwr_nor_lpuart_defconfig
Tom Rini 970bf8603b Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig
This converts the following to Kconfig:
   CONFIG_USE_BOOTCOMMAND
   CONFIG_BOOTCOMMAND
   CONFIG_RAMBOOTCOMMAND
   CONFIG_NFSBOOTCOMMAND

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-01 10:58:10 -05:00

76 lines
1.8 KiB
Text

CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_TARGET_LS1021ATWR=y
CONFIG_SYS_TEXT_BASE=0x60100000
CONFIG_SYS_MALLOC_LEN=0x1020000
CONFIG_NR_DRAM_BANKS=1
CONFIG_SYS_MEMTEST_START=0x80000000
CONFIG_SYS_MEMTEST_END=0x9fffffff
CONFIG_ENV_SIZE=0x20000
CONFIG_ENV_SECT_SIZE=0x20000
CONFIG_SYS_I2C_MXC_I2C1=y
CONFIG_SYS_I2C_MXC_I2C2=y
CONFIG_SYS_I2C_MXC_I2C3=y
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="ls1021a-twr-lpuart"
CONFIG_AHCI=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_SYS_LOAD_ADDR=0x82000000
CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
CONFIG_SYS_EXTRA_OPTIONS="LPUART"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0"
CONFIG_BOOTCOMMAND="run distro_bootcmd; run nor_bootcmd;env exists secureboot && esbc_halt;"
CONFIG_SILENT_CONSOLE=y
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_MISC_INIT_R=y
CONFIG_ID_EEPROM=y
CONFIG_CMD_IMLS=y
CONFIG_CMD_GREPENV=y
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
CONFIG_CMD_MEMINFO=y
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_GPT=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0x60300000
CONFIG_DM=y
CONFIG_SATA_CEVA=y
CONFIG_FSL_CAAM=y
CONFIG_DM_I2C=y
CONFIG_SPL_SYS_I2C_LEGACY=y
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
CONFIG_SYS_I2C_EEPROM_ADDR=0x53
CONFIG_FSL_ESDHC=y
CONFIG_MTD=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_FLASH_CFI_DRIVER=y
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
CONFIG_SYS_FLASH_CFI=y
CONFIG_PHY_ATHEROS=y
CONFIG_DM_ETH=y
CONFIG_DM_MDIO=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
CONFIG_NVME=y
CONFIG_PCI=y
CONFIG_PCIE_LAYERSCAPE_RC=y
CONFIG_SYS_QE_FW_ADDR=0x60940000
CONFIG_DM_SCSI=y
CONFIG_DM_SERIAL=y
CONFIG_FSL_LPUART=y
CONFIG_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y