u-boot/include/configs/ls2080a_common.h
Tom Rini f76750d111 Convert CONFIG_CONS_INDEX et al to Kconfig
This converts the following to Kconfig:
   CONFIG_CONS_INDEX
   CONFIG_DEBUG_UART_CLOCK
   CONFIG_FSL_TZPC_BP147
   CONFIG_GENERIC_ATMEL_MCI
   CONFIG_IDENT_STRING
   CONFIG_LIBATA
   CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE
   CONFIG_LPC32XX_GPIO
   CONFIG_MP
   CONFIG_MPC8XXX_GPIO
   CONFIG_MTD_PARTITIONS
   CONFIG_MVGBE
   CONFIG_MXC_GPIO
   CONFIG_NR_DRAM_BANKS
   CONFIG_OF_BOARD_SETUP
   CONFIG_OF_STDOUT_VIA_ALIAS
   CONFIG_OF_SYSTEM_SETUP
   CONFIG_PREBOOT
   CONFIG_ROCKCHIP_SERIAL
   CONFIG_RTC_ENABLE_32KHZ_OUTPUT
   CONFIG_RTC_MV
   CONFIG_SCSI_AHCI
   CONFIG_SF_DEFAULT_BUS
   CONFIG_SF_DEFAULT_CS
   CONFIG_SF_DEFAULT_SPEED
   CONFIG_SOFT_SPI
   CONFIG_SPI_FLASH_EON
   CONFIG_SPI_FLASH_MACRONIX
   CONFIG_SPI_FLASH_MTD
   CONFIG_SPI_FLASH_SPANSION
   CONFIG_SPI_FLASH_SST
   CONFIG_SPI_FLASH_STMICRO
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_SYS_ARCH_TIMER
   CONFIG_SYS_BOARD
   CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
   CONFIG_SYS_DCACHE_OFF
   CONFIG_SYS_FDT_SAVE_ADDRESS
   CONFIG_SYS_FLASH_CFI
   CONFIG_SYS_FSL_ERRATUM_ESDHC135
   CONFIG_SYS_HAS_SERDES
   CONFIG_SYS_L2CACHE_OFF
   CONFIG_SYS_LITTLE_ENDIAN
   CONFIG_SYS_LOAD_ADDR
   CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
   CONFIG_SYS_NS16550
   CONFIG_SYS_PLLFIN
   CONFIG_SYS_SPI_U_BOOT_OFFS
   CONFIG_TIMER_SYS_TICK_CH
   CONFIG_USB_EHCI_FSL
   CONFIG_U_QE
   CONFIG_VERSION_VARIABLE

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-27 08:41:38 -05:00

187 lines
5.7 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2017 NXP
* Copyright (C) 2014 Freescale Semiconductor
*/
#ifndef __LS2_COMMON_H
#define __LS2_COMMON_H
#define CONFIG_REMAKE_ELF
#include <asm/arch/stream_id_lsch3.h>
#include <asm/arch/config.h>
/* Link Definitions */
#ifdef CONFIG_TFABOOT
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
#else
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
#endif
/* We need architecture specific misc initializations */
/* Link Definitions */
#ifndef CONFIG_SYS_FSL_DDR4
#define CONFIG_SYS_DDR_RAW_TIMING
#endif
#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL
#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2
/*
* SMP Definitinos
*/
#define CPU_RELEASE_ADDR secondary_boot_addr
#define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
#define CONFIG_SYS_DP_DDR_BASE 0x6000000000ULL
/*
* DDR controller use 0 as the base address for binding.
* It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
*/
#define CONFIG_SYS_DP_DDR_BASE_PHY 0
#define CONFIG_DP_DDR_CTRL 2
#define CONFIG_DP_DDR_NUM_CTRLS 1
#endif
/* Generic Timer Definitions */
/*
* This is not an accurate number. It is used in start.S. The frequency
* will be udpated later when get_bus_freq(0) is available.
*/
#define COUNTER_FREQUENCY 25000000 /* 25MHz */
/* GPIO */
/* I2C */
/* Serial Port */
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_serial_clock())
/*
* During booting, IFC is mapped at the region of 0x30000000.
* But this region is limited to 256MB. To accommodate NOR, promjet
* and FPGA. This region is divided as below:
* 0x30000000 - 0x37ffffff : 128MB : NOR flash
* 0x38000000 - 0x3BFFFFFF : 64MB : Promjet
* 0x3C000000 - 0x40000000 : 64MB : FPGA etc
*
* To accommodate bigger NOR flash and other devices, we will map IFC
* chip selects to as below:
* 0x5_1000_0000..0x5_1fff_ffff Memory Hole
* 0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB)
* 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB
* 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet)
* 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet)
*
* For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
* CONFIG_SYS_FLASH_BASE has the final address (core view)
* CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
* CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
* CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
*/
#define CONFIG_SYS_FLASH_BASE 0x580000000ULL
#define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000
#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
#define CONFIG_SYS_FLASH1_BASE_PHYS 0xC0000000
#define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000
#ifndef __ASSEMBLY__
unsigned long long get_qixis_addr(void);
#endif
#define QIXIS_BASE get_qixis_addr()
#define QIXIS_BASE_PHYS 0x20000000
#define QIXIS_BASE_PHYS_EARLY 0xC000000
#define QIXIS_STAT_PRES1 0xb
#define QIXIS_SDID_MASK 0x07
#define QIXIS_ESDHC_NO_ADAPTER 0x7
#define CONFIG_SYS_NAND_BASE 0x530000000ULL
#define CONFIG_SYS_NAND_BASE_PHYS 0x30000000
/* MC firmware */
/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
/* For LS2085A */
#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000
/* Define phy_reset function to boot the MC based on mcinitcmd.
* This happens late enough to properly fixup u-boot env MAC addresses.
*/
#define CONFIG_RESET_PHY_R
/*
* Carve out a DDR region which will not be used by u-boot/Linux
*
* It will be used by MC and Debug Server. The MC region must be
* 512MB aligned, so the min size to hide is 512MB.
*/
#ifdef CONFIG_FSL_MC_ENET
#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (128UL * 1024 * 1024)
#endif
/* Miscellaneous configurable options */
/* Physical Memory Map */
/* fixme: these need to be checked against the board */
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"loadaddr=0x80100000\0" \
"kernel_addr=0x100000\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0x581000000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"console=ttyAMA0,38400n8\0" \
"mcinitcmd=fsl_mc start mc 0x580a00000" \
" 0x580e00000 \0"
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
#define CONFIG_SPL_MAX_SIZE 0x16000
#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#ifdef CONFIG_NAND_BOOT
#define CONFIG_SYS_NAND_U_BOOT_DST 0x80400000
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
#endif
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
#define CONFIG_SYS_MONITOR_LEN (1024 * 1024)
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#include <asm/arch/soc.h>
#endif /* __LS2_COMMON_H */