u-boot/arch/arm/dts/armada-3720-uDPU.dtsi
Robert Marko b4108f3fd3 arm: mvebu: add support for Methode eDPU
Methode eDPU is an Armada 3720 power board based on the Methode uDPU.

They feature the same CPU, RAM, and storage as well as the form factor.

However, eDPU only has one SFP slot plus a copper G.hn port which does not
work under U-boot.

In order to reduce duplication, split the uDPU DTS into a common one.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-07-21 10:14:04 +02:00

160 lines
2.8 KiB
Text

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Device tree for the uDPU board.
* Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
* Copyright (C) 2016 Marvell
* Copyright (C) 2019 Methode Electronics
* Copyright (C) 2019 Telus
*
* Vladimir Vid <vladimir.vid@sartura.hr>
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include "armada-372x.dtsi"
/ {
chosen {
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
};
leds {
compatible = "gpio-leds";
led-power1 {
label = "udpu:green:power";
gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
};
led-power2 {
label = "udpu:red:power";
gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
};
led-network1 {
label = "udpu:green:network";
gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
};
led-network2 {
label = "udpu:red:network";
gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
};
led-alarm1 {
label = "udpu:green:alarm";
gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
};
led-alarm2 {
label = "udpu:red:alarm";
gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
};
};
sfp_eth1: sfp-eth1 {
compatible = "sff,sfp";
i2c-bus = <&i2c1>;
los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
maximum-power-milliwatt = <3000>;
};
};
&sdhci0 {
status = "okay";
bus-width = <8>;
mmc-ddr-1_8v;
mmc-hs400-1_8v;
marvell,pad-type = "fixed-1-8v";
non-removable;
no-sd;
no-sdio;
};
&spi0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&spi_quad_pins>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <54000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "firmware";
reg = <0x0 0x180000>;
};
partition@180000 {
label = "u-boot-env";
reg = <0x180000 0x10000>;
};
};
};
};
&pinctrl_nb {
i2c2_recovery_pins: i2c2-recovery-pins {
groups = "i2c2";
function = "gpio";
};
};
&i2c1 {
status = "okay";
pinctrl-names = "default", "recovery";
pinctrl-0 = <&i2c2_pins>;
pinctrl-1 = <&i2c2_recovery_pins>;
/delete-property/mrvl,i2c-fast-mode;
scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
temp-sensor@48 {
compatible = "ti,tmp75c";
reg = <0x48>;
};
temp-sensor@49 {
compatible = "ti,tmp75c";
reg = <0x49>;
};
};
&eth0 {
status = "okay";
managed = "in-band-status";
phys = <&comphy1 0>;
};
&eth1 {
phy-mode = "sgmii";
status = "okay";
managed = "in-band-status";
phys = <&comphy0 1>;
sfp = <&sfp_eth1>;
};
&usb3 {
status = "okay";
phys = <&usb2_utmi_otg_phy>;
phy-names = "usb2-utmi-otg-phy";
};
&uart0 {
status = "okay";
};