mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-04 18:41:03 +00:00
c2120fbfbc
The sandburst-specific i2c drivers have been deleted, conflict was just over the SPDX conversion. Conflicts: board/sandburst/common/ppc440gx_i2c.c board/sandburst/common/ppc440gx_i2c.h Signed-off-by: Tom Rini <trini@ti.com>
420 lines
14 KiB
C
420 lines
14 KiB
C
/*
|
|
* (C) Copyright 2008
|
|
* Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com
|
|
*
|
|
* based on the Sequoia board configuration by
|
|
* Stefan Roese, Jacqueline Pira-Ferriol and Alain Saurel
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
**********************************************************************
|
|
* DU440.h - configuration for esd's DU440 board (Power PC440EPx)
|
|
**********************************************************************
|
|
*/
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
#define CONFIG_DU440 1 /* Board is esd DU440 */
|
|
#define CONFIG_440EPX 1 /* Specific PPC440EPx */
|
|
#define CONFIG_4xx 1 /* ... PPC4xx family */
|
|
#define CONFIG_SYS_CLK_FREQ 33333400 /* external freq to pll */
|
|
|
|
#ifndef CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_SYS_TEXT_BASE 0xFFFA0000
|
|
#endif
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
|
|
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
|
|
#define CONFIG_LAST_STAGE_INIT 1 /* last_stage_init */
|
|
|
|
/*
|
|
* Base addresses -- Note these are effective addresses where the
|
|
* actual resources get mapped (not physical addresses)
|
|
*/
|
|
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
|
|
#define CONFIG_SYS_MALLOC_LEN (8 << 20) /* Reserve 8 MB for malloc() */
|
|
|
|
#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
|
|
#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_SYS_NAND0_ADDR 0xd0000000 /* NAND Flash */
|
|
#define CONFIG_SYS_NAND1_ADDR 0xd0100000 /* NAND Flash */
|
|
#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */
|
|
#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */
|
|
#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
|
|
#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
|
|
#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
|
|
#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
|
|
#define CONFIG_SYS_PCI_IOBASE 0xe8000000
|
|
#define CONFIG_SYS_PCI_SUBSYS_VENDORID PCI_VENDOR_ID_ESDGMBH
|
|
#define CONFIG_SYS_PCI_SUBSYS_ID 0x0444 /* device ID for DU440 */
|
|
|
|
#define CONFIG_SYS_USB2D0_BASE 0xe0000100
|
|
#define CONFIG_SYS_USB_DEVICE 0xe0000000
|
|
#define CONFIG_SYS_USB_HOST 0xe0000400
|
|
|
|
/*
|
|
* Initial RAM & stack pointer
|
|
*/
|
|
/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
|
|
#define CONFIG_SYS_INIT_RAM_OCM 1 /* OCM as init ram */
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */
|
|
|
|
#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10)
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/*
|
|
* Serial Port
|
|
*/
|
|
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
|
|
#define CONFIG_SYS_NS16550
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
|
|
#undef CONFIG_SYS_EXT_SERIAL_CLOCK
|
|
#define CONFIG_BAUDRATE 115200
|
|
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
|
|
|
|
/*
|
|
* Video Port
|
|
*/
|
|
#define CONFIG_VIDEO
|
|
#define CONFIG_VIDEO_SMI_LYNXEM
|
|
#define CONFIG_CFB_CONSOLE
|
|
#define CONFIG_VIDEO_LOGO
|
|
#define CONFIG_VGA_AS_SINGLE_DEVICE
|
|
#define CONFIG_SPLASH_SCREEN
|
|
#define CONFIG_SPLASH_SCREEN_ALIGN
|
|
#define CONFIG_VIDEO_BMP_GZIP /* gzip compressed bmp images */
|
|
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (4 << 20) /* for decompressed img */
|
|
#define CONFIG_SYS_DEFAULT_VIDEO_MODE 0x31a /* 1280x1024,16bpp */
|
|
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
|
|
#define CONFIG_SYS_ISA_IO CONFIG_SYS_PCI_IOBASE
|
|
|
|
/*
|
|
* Environment
|
|
*/
|
|
#define CONFIG_ENV_IS_IN_EEPROM 1 /* use FLASH for environment vars */
|
|
|
|
/*
|
|
* FLASH related
|
|
*/
|
|
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
|
|
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
|
|
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
|
|
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
|
|
/* CFI_FLASH_PROTECTION make flash_protect hang sometimes -> disabled */
|
|
#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */
|
|
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO
|
|
#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
|
|
|
|
#ifdef CONFIG_ENV_IS_IN_FLASH
|
|
#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
|
|
#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
|
|
|
|
/* Address and size of Redundant Environment Sector */
|
|
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
|
|
#endif
|
|
|
|
#ifdef CONFIG_ENV_IS_IN_EEPROM
|
|
#define CONFIG_ENV_OFFSET 0 /* environment starts at */
|
|
/* the beginning of the EEPROM */
|
|
#define CONFIG_ENV_SIZE 0x1000 /* 4096 bytes may be used for env vars */
|
|
#endif
|
|
|
|
/*
|
|
* DDR SDRAM
|
|
*/
|
|
#define CONFIG_SYS_MBYTES_SDRAM (1024) /* 512 MiB TODO: remove */
|
|
#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
|
|
#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
|
|
/* 440EPx errata CHIP 11 */
|
|
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
|
|
#define CONFIG_DDR_ECC /* Use ECC when available */
|
|
#define SPD_EEPROM_ADDRESS {0x50}
|
|
#define CONFIG_PROG_SDRAM_TLB
|
|
|
|
/*
|
|
* I2C
|
|
*/
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_PPC4XX
|
|
#define CONFIG_SYS_I2C_PPC4XX_CH0
|
|
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
|
|
#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
|
|
#define CONFIG_SYS_I2C_PPC4XX_CH1
|
|
#define CONFIG_SYS_I2C_PPC4XX_SPEED_1 100000
|
|
#define CONFIG_SYS_I2C_PPC4XX_SLAVE_1 0x7F
|
|
|
|
#define CONFIG_SYS_SPD_BUS_NUM 0
|
|
#define IIC1_MCP3021_ADDR 0x4d
|
|
#define IIC1_USB2507_ADDR 0x2c
|
|
#define CONFIG_SYS_I2C_NOPROBES { {1, IIC1_USB2507_ADDR} }
|
|
|
|
#define CONFIG_SYS_I2C_MULTI_EEPROMS
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01
|
|
|
|
#define CONFIG_SYS_EEPROM_WREN 1
|
|
#define CONFIG_SYS_I2C_BOOT_EEPROM_ADDR 0x52
|
|
|
|
/*
|
|
* standard dtt sensor configuration - bottom bit will determine local or
|
|
* remote sensor of the TMP401
|
|
*/
|
|
#define CONFIG_DTT_SENSORS { 0, 1 }
|
|
|
|
/*
|
|
* The PMC440 uses a TI TMP401 temperature sensor. This part
|
|
* is basically compatible to the ADM1021 that is supported
|
|
* by U-Boot.
|
|
*
|
|
* - i2c addr 0x4c
|
|
* - conversion rate 0x02 = 0.25 conversions/second
|
|
* - ALERT ouput disabled
|
|
* - local temp sensor enabled, min set to 0 deg, max set to 70 deg
|
|
* - remote temp sensor enabled, min set to 0 deg, max set to 70 deg
|
|
*/
|
|
#define CONFIG_DTT_ADM1021
|
|
#define CONFIG_SYS_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} }
|
|
|
|
/*
|
|
* RTC stuff
|
|
*/
|
|
#define CONFIG_RTC_DS1338
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"ethrotate=no\0" \
|
|
"hostname=du440\0" \
|
|
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=${serverip}:${rootpath}\0" \
|
|
"ramargs=setenv bootargs root=/dev/ram rw\0" \
|
|
"addip=setenv bootargs ${bootargs} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
|
|
":${hostname}:${netdev}:off panic=1\0" \
|
|
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
|
|
"flash_self=run ramargs addip addtty optargs;" \
|
|
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
|
|
"net_nfs=tftp 200000 ${img};run nfsargs addip addtty optargs;" \
|
|
"bootm\0" \
|
|
"rootpath=/tftpboot/du440/target_root_du440\0" \
|
|
"img=/tftpboot/du440/uImage\0" \
|
|
"kernel_addr=FFC00000\0" \
|
|
"ramdisk_addr=FFE00000\0" \
|
|
"initrd_high=30000000\0" \
|
|
"load=tftp 100000 /tftpboot/du440/u-boot.bin\0" \
|
|
"update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \
|
|
"cp.b 100000 FFFA0000 60000\0" \
|
|
""
|
|
|
|
#define CONFIG_PREBOOT /* enable preboot variable */
|
|
|
|
#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
#ifndef __ASSEMBLY__
|
|
int du440_phy_addr(int devnum);
|
|
#endif
|
|
|
|
#define CONFIG_PPC4xx_EMAC
|
|
#define CONFIG_IBM_EMAC4_V4 1
|
|
#define CONFIG_MII 1 /* MII PHY management */
|
|
#define CONFIG_PHY_ADDR du440_phy_addr(0) /* PHY address */
|
|
|
|
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
|
|
#undef CONFIG_PHY_GIGE /* no GbE detection */
|
|
|
|
#define CONFIG_HAS_ETH0
|
|
#define CONFIG_SYS_RX_ETH_BUFFER 128
|
|
|
|
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
|
|
#define CONFIG_PHY1_ADDR du440_phy_addr(1)
|
|
|
|
/*
|
|
* USB
|
|
*/
|
|
#define CONFIG_USB_OHCI_NEW
|
|
#define CONFIG_USB_STORAGE
|
|
#define CONFIG_SYS_OHCI_BE_CONTROLLER
|
|
|
|
#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
|
|
#define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST
|
|
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "du440"
|
|
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
|
|
|
|
/* Comment this out to enable USB 1.1 device */
|
|
#define USB_2_0_DEVICE
|
|
|
|
/* Partitions */
|
|
#define CONFIG_MAC_PARTITION
|
|
#define CONFIG_DOS_PARTITION
|
|
#define CONFIG_ISO_PARTITION
|
|
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_ASKENV
|
|
#define CONFIG_CMD_BMP
|
|
#define CONFIG_CMD_BSP
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_DIAG
|
|
#define CONFIG_CMD_DTT
|
|
#define CONFIG_CMD_EEPROM
|
|
#define CONFIG_CMD_ELF
|
|
#define CONFIG_CMD_FAT
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_IRQ
|
|
#define CONFIG_CMD_MII
|
|
#define CONFIG_CMD_NAND
|
|
#define CONFIG_CMD_NET
|
|
#define CONFIG_CMD_NFS
|
|
#define CONFIG_CMD_PCI
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_REGINFO
|
|
#define CONFIG_CMD_SDRAM
|
|
#define CONFIG_CMD_SOURCE
|
|
#define CONFIG_CMD_USB
|
|
|
|
#define CONFIG_SUPPORT_VFAT
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
/* Print Buffer Size */
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x3f000000 /* 4 ... < 1GB DRAM */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
|
|
|
|
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
|
|
|
|
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
|
|
#define CONFIG_LOOPW 1 /* enable loopw command */
|
|
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
|
|
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
|
|
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
|
|
|
|
#define CONFIG_AUTOBOOT_KEYED 1
|
|
#define CONFIG_AUTOBOOT_PROMPT \
|
|
"Press SPACE to abort autoboot in %d seconds\n", bootdelay
|
|
#define CONFIG_AUTOBOOT_DELAY_STR "d"
|
|
#define CONFIG_AUTOBOOT_STOP_STR " "
|
|
|
|
/*
|
|
* PCI stuff
|
|
*/
|
|
#define CONFIG_PCI /* include pci support */
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
|
|
#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */
|
|
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
|
#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE*/
|
|
|
|
/* Board-specific PCI */
|
|
#define CONFIG_SYS_PCI_TARGET_INIT
|
|
#define CONFIG_SYS_PCI_MASTER_INIT
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*
|
|
* External Bus Controller (EBC) Setup
|
|
*/
|
|
#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE
|
|
|
|
#define CONFIG_SYS_CPLD_BASE 0xC0000000
|
|
#define CONFIG_SYS_CPLD_RANGE 0x00000010
|
|
#define CONFIG_SYS_DUMEM_BASE 0xC0100000
|
|
#define CONFIG_SYS_DUMEM_RANGE 0x00100000
|
|
#define CONFIG_SYS_DUIO_BASE 0xC0200000
|
|
#define CONFIG_SYS_DUIO_RANGE 0x00010000
|
|
|
|
#define CONFIG_SYS_NAND0_CS 2 /* NAND chip connected to CSx */
|
|
#define CONFIG_SYS_NAND1_CS 3 /* NAND chip connected to CSx */
|
|
/* Memory Bank 0 (NOR-FLASH) initialization */
|
|
#define CONFIG_SYS_EBC_PB0AP 0x04017200
|
|
#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xda000)
|
|
|
|
/* Memory Bank 1 (CPLD, 16 bytes needed, but 1MB is minimum) */
|
|
#define CONFIG_SYS_EBC_PB1AP 0x018003c0
|
|
#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_CPLD_BASE | 0x18000)
|
|
|
|
/* Memory Bank 2 (NAND-FLASH) initialization */
|
|
#define CONFIG_SYS_EBC_PB2AP 0x018003c0
|
|
#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_NAND0_ADDR | 0x1c000)
|
|
|
|
/* Memory Bank 3 (NAND-FLASH) initialization */
|
|
#define CONFIG_SYS_EBC_PB3AP 0x018003c0
|
|
#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND1_ADDR | 0x1c000)
|
|
|
|
/* Memory Bank 4 (DUMEM, 1MB) initialization */
|
|
#define CONFIG_SYS_EBC_PB4AP 0x018053c0
|
|
#define CONFIG_SYS_EBC_PB4CR (CONFIG_SYS_DUMEM_BASE | 0x18000)
|
|
|
|
/* Memory Bank 5 (DUIO, 64KB needed, but 1MB is minimum) */
|
|
#define CONFIG_SYS_EBC_PB5AP 0x018053c0
|
|
#define CONFIG_SYS_EBC_PB5CR (CONFIG_SYS_DUIO_BASE | 0x18000)
|
|
|
|
/*
|
|
* NAND FLASH
|
|
*/
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 2
|
|
#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
|
|
#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND0_ADDR + CONFIG_SYS_NAND0_CS, \
|
|
CONFIG_SYS_NAND1_ADDR + CONFIG_SYS_NAND1_CS}
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
|
|
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
|
|
#endif
|
|
|
|
#define CONFIG_SOURCE 1
|
|
|
|
#define CONFIG_OF_LIBFDT
|
|
#define CONFIG_OF_BOARD_SETUP
|
|
|
|
#endif /* __CONFIG_H */
|