mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-11 23:47:24 +00:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
259 lines
9.2 KiB
INI
259 lines
9.2 KiB
INI
#
|
|
# (C) Copyright 2012
|
|
# Stefan Bigler, Keymile AG, stefan.bigler@keymile.com
|
|
# Norbert Mayer, Keymile AG, norbert.mayer@keymile.com
|
|
# Deepak Patel, XENTECH Limited, deepak.patel@xentech.co.uk
|
|
#
|
|
# SPDX-License-Identifier: GPL-2.0+
|
|
#
|
|
# Refer doc/README.kwbimage for more details about how-to configure
|
|
# and create kirkwood boot image
|
|
#
|
|
# This configuration applies to COGE5 design (ARM-part)
|
|
# Two 8-Bit devices are connected on the 16-Bit bus on the same
|
|
# chip-select. The supported devices are
|
|
# MT47H256M8EB-3IT:C
|
|
# MT47H256M8EB-25EIT:C
|
|
|
|
# Boot Media configurations
|
|
BOOT_FROM spi # Boot from SPI flash
|
|
|
|
DATA 0xFFD10000 0x01112222 # MPP Control 0 Register
|
|
# bit 3-0: 2, MPPSel0 SPI_CSn (1=NF_IO[2])
|
|
# bit 7-4: 2, MPPSel1 SPI_MOSI (1=NF_IO[3])
|
|
# bit 12-8: 2, MPPSel2 SPI_SCK (1=NF_IO[4])
|
|
# bit 15-12: 2, MPPSel3 SPI_MISO (1=NF_IO[5])
|
|
# bit 19-16: 1, MPPSel4 NF_IO[6]
|
|
# bit 23-20: 1, MPPSel5 NF_IO[7]
|
|
# bit 27-24: 1, MPPSel6 SYSRST_O
|
|
# bit 31-28: 0, MPPSel7 GPO[7]
|
|
|
|
DATA 0xFFD10004 0x03303300 # MPP Control 1 Register
|
|
# bit 3-0: 0, MPPSel8 GPIO[8] CPU_SDA bitbanged
|
|
# bit 7-4: 0, MPPSel9 GPIO[9] CPU_SCL bitbanged
|
|
# bit 12-8: 3, MPPSel10 UA0_TXD
|
|
# bit 15-12: 3, MPPSel11 UA0_RXD
|
|
# bit 19-16: 0, MPPSel12 not connected
|
|
# bit 23-20: 3, MPPSel13 GPIO[14]
|
|
# bit 27-24: 3, MPPSel14 GPIO[15]
|
|
# bit 31-28: 0, MPPSel15 GPIO[16] BOOT_FL_SEL (SPI-MUX Signal)
|
|
|
|
DATA 0xFFD10008 0x00001100 # MPP Control 2 Register
|
|
# bit 3-0: 0, MPPSel16 GPIO[16]
|
|
# bit 7-4: 0, MPPSel17 not connected
|
|
# bit 11-8: 1, MPPSel18 NF_IO[0]
|
|
# bit 15-12: 1, MPPSel19 NF_IO[1]
|
|
# bit 19-16: 0, MPPSel20 GPIO[20]
|
|
# bit 23-20: 0, MPPSel21 GPIO[21]
|
|
# bit 27-24: 0, MPPSel22 GPIO[22]
|
|
# bit 31-28: 0, MPPSel23 GPIO[23]
|
|
|
|
# MPP Control 3-6 Register untouched (MPP24-49)
|
|
|
|
DATA 0xFFD100E0 0x1B1B1B1B # IO Configuration 0 Register
|
|
# bit 2-0: 3, Reserved
|
|
# bit 5-3: 3, Reserved
|
|
# bit 6: 0, Reserved
|
|
# bit 7: 0, RGMII-pads voltage = 3.3V
|
|
# bit 10-8: 3, Reserved
|
|
# bit 13-11: 3, Reserved
|
|
# bit 14: 0, Reserved
|
|
# bit 15: 0, MPP RGMII-pads voltage = 3.3V
|
|
# bit 31-16 0x1B1B, Reserved
|
|
|
|
DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register
|
|
# bit 0-1: 2, Tag RAM RTC RAM0
|
|
# bit 3-2: 1, Tag RAM WTC RAM0
|
|
# bit 7-4: 6, Reserved
|
|
# bit 9-8: 2, Valid RAM RTC RAM
|
|
# bit 11-10: 1, Valid RAM WTC RAM
|
|
# bit 13-12: 2, Dirty RAM RTC RAM
|
|
# bit 15-14: 1, Dirty RAM WTC RAM
|
|
# bit 17-16: 2, Data RAM RTC RAM0
|
|
# bit 19-18: 1, Data RAM WTC RAM0
|
|
# bit 21-20: 2, Data RAM RTC RAM1
|
|
# bit 23-22: 1, Data RAM WTC RAM1
|
|
# bit 25-24: 2, Data RAM RTC RAM2
|
|
# bit 27-26: 1, Data RAM WTC RAM2
|
|
# bit 29-28: 2, Data RAM RTC RAM3
|
|
# bit 31-30: 1, Data RAM WTC RAM4
|
|
|
|
DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register
|
|
# bit 15-0: ?, Reserved
|
|
# bit 17-16: 2, ECC RAM RTC RAM0
|
|
# bit 19-18: 1, ECC RAM WTC RAM0
|
|
# bit 31-20: ?,Reserved
|
|
|
|
# NOTE: Don't write on 0x20148 , 0x2014c and 0x20154, leave them untouched!
|
|
# If not it could cause KW Exceptions during boot in Fast Corners/High Voltage
|
|
|
|
# SDRAM initalization
|
|
DATA 0xFFD01400 0x430004E0 # SDRAM Configuration Register
|
|
# bit 13-0: 0x4E0, DDR2 clks refresh rate
|
|
# bit 14: 0, reserved
|
|
# bit 15: 0, reserved
|
|
# bit 16: 0, CPU to Dram Write buffer policy
|
|
# bit 17: 0, Enable Registered DIMM or Equivalent Sampling Logic
|
|
# bit 19-18: 0, reserved
|
|
# bit 23-20: 0, reserved
|
|
# bit 24: 1, enable exit self refresh mode on DDR access
|
|
# bit 25: 1, required
|
|
# bit 29-26: 0, reserved
|
|
# bit 31-30: 1, reserved
|
|
|
|
DATA 0xFFD01404 0x36543000 # DDR Controller Control Low
|
|
# bit 3-0: 0, reserved
|
|
# bit 4: 0, 2T mode =addr/cmd in same cycle
|
|
# bit 5: 0, clk is driven during self refresh, we don't care for APX
|
|
# bit 6: 0, use recommended falling edge of clk for addr/cmd
|
|
# bit 7-11: 0, reserved
|
|
# bit 12-13: 1, reserved, required 1
|
|
# bit 14: 0, input buffer always powered up
|
|
# bit 17-15: 0, reserved
|
|
# bit 18: 1, cpu lock transaction enabled
|
|
# bit 19: 0, reserved
|
|
# bit 23-20: 5, recommended value for CL=4 and STARTBURST_DEL disabled bit31=0
|
|
# bit 27-24: 6, CL+1, STARTBURST sample stages, freq 200-399MHz, unbuffer DIMM
|
|
# bit 30-28: 3, required
|
|
# bit 31: 0, no additional STARTBURST delay
|
|
|
|
DATA 0xFFD01408 0x2202444E # DDR Timing (Low) (active cycles value +1)
|
|
# bit 3-0: 0xe, TRAS = 45ns -> 15 clk cycles
|
|
# bit 7-4: 0x4, TRCD = 15ns -> 5 clk cycles
|
|
# bit 11-8: 0x4, TRP = 15ns -> 5 clk cycles
|
|
# bit 15-12: 0x4, TWR = 15ns -> 5 clk cycles
|
|
# bit 19-16: 0x2, TWTR = 7,5ns -> 3 clk cycles
|
|
# bit 20: 0, extended TRAS msb
|
|
# bit 23-21: 0, reserved
|
|
# bit 27-24: 0x2, TRRD = 7,5ns -> 3 clk cycles
|
|
# bit 31-28: 0x2, TRTP = 7,5ns -> 3 clk cycles
|
|
|
|
DATA 0xFFD0140C 0x0000003E # DDR Timing (High)
|
|
# bit 6-0: 0x3E, TRFC = 195ns -> 63 clk cycles
|
|
# bit 8-7: 0, TR2R
|
|
# bit 10-9: 0, TR2W
|
|
# bit 12-11: 0, TW2W
|
|
# bit 31-13: 0, reserved
|
|
|
|
DATA 0xFFD01410 0x00000000 # DDR Address Control
|
|
# bit 1-0: 0, Cs0width=x8 (2 devices)
|
|
# bit 3-2: 0, Cs0size=2Gb
|
|
# bit 5-4: 0, Cs1width=nonexistent
|
|
# bit 7-6: 0, Cs1size =nonexistent
|
|
# bit 9-8: 0, Cs2width=nonexistent
|
|
# bit 11-10: 0, Cs2size =nonexistent
|
|
# bit 13-12: 0, Cs3width=nonexistent
|
|
# bit 15-14: 0, Cs3size =nonexistent
|
|
# bit 16: 0, Cs0AddrSel
|
|
# bit 17: 0, Cs1AddrSel
|
|
# bit 18: 0, Cs2AddrSel
|
|
# bit 19: 0, Cs3AddrSel
|
|
# bit 31-20: 0, required
|
|
|
|
DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
|
|
# bit 0: 0, OpenPage enabled
|
|
# bit 31-1: 0, required
|
|
|
|
DATA 0xFFD01418 0x00000000 # DDR Operation
|
|
# bit 3-0: 0, DDR cmd
|
|
# bit 31-4: 0, required
|
|
|
|
DATA 0xFFD0141C 0x00000652 # DDR Mode
|
|
# bit 2-0: 2, Burst Length = 4
|
|
# bit 3: 0, Burst Type
|
|
# bit 6-4: 5, CAS Latency = 5
|
|
# bit 7: 0, Test mode
|
|
# bit 8: 0, DLL Reset
|
|
# bit 11-9: 3, Write recovery for auto-precharge must be 3
|
|
# bit 12: 0, Active power down exit time, fast exit
|
|
# bit 14-13: 0, reserved
|
|
# bit 31-15: 0, reserved
|
|
|
|
DATA 0xFFD01420 0x00000006 # DDR Extended Mode
|
|
# bit 0: 0, DDR DLL enabled
|
|
# bit 1: 1, DDR drive strenght reduced
|
|
# bit 2: 1, DDR ODT control lsb, 75ohm termination [RTT0]
|
|
# bit 5-3: 0, required
|
|
# bit 6: 0, DDR ODT control msb, 75ohm termination [RTT1]
|
|
# bit 9-7: 0, required
|
|
# bit 10: 0, differential DQS enabled
|
|
# bit 11: 0, required
|
|
# bit 12: 0, DDR output buffer enabled
|
|
# bit 31-13: 0 required
|
|
|
|
DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
|
|
# bit 2-0: 7, required
|
|
# bit 3: 1, MBUS Burst Chop disabled
|
|
# bit 6-4: 7, required
|
|
# bit 7: 0, reserved
|
|
# bit 8: 1, add sample stage required for > 266Mhz
|
|
# bit 9: 0, no half clock cycle addition to dataout
|
|
# bit 10: 0, 1/4 clock cycle skew enabled for addr/ctl signals
|
|
# bit 11: 0, 1/4 clock cycle skew disabled for write mesh
|
|
# bit 15-12:0xf, required
|
|
# bit 31-16: 0, required
|
|
|
|
DATA 0xFFD01428 0x00084520 # DDR2 SDRAM Timing Low
|
|
# bit 3-0: 0, required
|
|
# bit 7-4: 2, M_ODT assertion 2 cycles after read start command
|
|
# bit 11-8: 5, M_ODT de-assertion 5 cycles after read start command
|
|
# (ODT turn off delay 2,5 clk cycles)
|
|
# bit 15-12: 4, internal ODT time based on bit 7-4
|
|
# with the considered SDRAM internal delay
|
|
# bit 19-16: 8, internal ODT de-assertion based on bit 11-8
|
|
# with the considered SDRAM internal delay
|
|
# bit 31-20: 0, required
|
|
|
|
DATA 0xFFD0147c 0x00008452 # DDR2 SDRAM Timing High
|
|
# bit 3-0: 2, M_ODT assertion same as bit 11-8
|
|
# bit 7-4: 5, M_ODT de-assertion same as bit 15-12
|
|
# bit 11-8: 4, internal ODT assertion 2 cycles after write start command
|
|
# with the considered SDRAM internal delay
|
|
# bit 15-12: 8, internal ODT de-assertion 5 cycles after write start command
|
|
# with the considered SDRAM internal delay
|
|
|
|
DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
|
|
# bit 23-0: 0, reserved
|
|
# bit 31-24: 0, CPU CS Window0 Base Address, addr bits [31:24]
|
|
|
|
DATA 0xFFD01504 0x1FFFFFF1 # CS[0]n Size
|
|
# bit 0: 1, Window enabled
|
|
# bit 1: 0, Write Protect disabled
|
|
# bit 3-2: 0, CS0 hit selected
|
|
# bit 23-4:ones, required
|
|
# bit 31-24:0x1F, Size (i.e. 512MB)
|
|
|
|
DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
|
|
DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
|
|
DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
|
|
|
|
DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low)
|
|
# bit 3-0: 0, ODT0Rd, MODT[0] not asserted during read from DRAM CS0
|
|
# bit 7-4: 0, ODT0Rd, MODT[1] not asserted
|
|
# bit 11-8: 0, required
|
|
# big 15-11: 0, required
|
|
# bit 19-16: 1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
|
|
# bit 23-20: 0, ODT0Wr, MODT[1] not asserted
|
|
# bit 27-24: 0, required
|
|
# bit 31-28: 0, required
|
|
|
|
DATA 0xFFD01498 0x00000004 # DDR ODT Control (High)
|
|
# bit 1-0: 0, ODT0 controlled by ODT Control (low) register above
|
|
# bit 3-2: 1, ODT1 never active
|
|
# bit 31-4: 0, required
|
|
|
|
DATA 0xFFD0149C 0x0000E801 # CPU ODT Control
|
|
# bit 3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
|
|
# bit 7-4: 0, ODT0Wr, Internal ODT not asserted during write to DRAM bank0
|
|
# bit 9-8: 0, ODTEn, controlled by ODT0Rd and ODT0Wr
|
|
# bit 11-10: 2, DQ_ODTSel. ODT select turned on, 75 ohm
|
|
# bit 13-12: 2, STARTBURST ODT buffer selected, 75 ohm
|
|
# bit 14: 1, STARTBURST ODT enabled
|
|
# bit 15: 1, Use ODT Block
|
|
|
|
DATA 0xFFD01480 0x00000001 # DDR Initialization Control
|
|
# bit 0: 1, enable DDR init upon this register write
|
|
# bit 31-1: 0, reserved
|
|
|
|
# End of Header extension
|
|
DATA 0x0 0x0
|