u-boot/arch/arm/mach-k3/am6_init.c
Andreas Dannenberg c222e3d927 armV7R: K3: am654: Load SYSFW binary and config from boot media
Use the System Firmware (SYSFW) loader framework to load and start
the SYSFW as part of the AM654 early initialization sequence. While
at it also initialize the WKUP_UART0 pinmux as it is used by SYSFW
to print diagnostic messages.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
2019-07-17 11:12:54 -04:00

212 lines
5.7 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* K3: Architecture initialization
*
* Copyright (C) 2017-2018 Texas Instruments Incorporated - http://www.ti.com/
* Lokesh Vutla <lokeshvutla@ti.com>
*/
#include <common.h>
#include <asm/io.h>
#include <spl.h>
#include <asm/arch/hardware.h>
#include <asm/arch/sysfw-loader.h>
#include "common.h"
#include <dm.h>
#include <dm/uclass-internal.h>
#include <dm/pinctrl.h>
#ifdef CONFIG_SPL_BUILD
static void mmr_unlock(u32 base, u32 partition)
{
/* Translate the base address */
phys_addr_t part_base = base + partition * CTRL_MMR0_PARTITION_SIZE;
/* Unlock the requested partition if locked using two-step sequence */
writel(CTRLMMR_LOCK_KICK0_UNLOCK_VAL, part_base + CTRLMMR_LOCK_KICK0);
writel(CTRLMMR_LOCK_KICK1_UNLOCK_VAL, part_base + CTRLMMR_LOCK_KICK1);
}
static void ctrl_mmr_unlock(void)
{
/* Unlock all WKUP_CTRL_MMR0 module registers */
mmr_unlock(WKUP_CTRL_MMR0_BASE, 0);
mmr_unlock(WKUP_CTRL_MMR0_BASE, 1);
mmr_unlock(WKUP_CTRL_MMR0_BASE, 2);
mmr_unlock(WKUP_CTRL_MMR0_BASE, 3);
mmr_unlock(WKUP_CTRL_MMR0_BASE, 6);
mmr_unlock(WKUP_CTRL_MMR0_BASE, 7);
/* Unlock all MCU_CTRL_MMR0 module registers */
mmr_unlock(MCU_CTRL_MMR0_BASE, 0);
mmr_unlock(MCU_CTRL_MMR0_BASE, 1);
mmr_unlock(MCU_CTRL_MMR0_BASE, 2);
mmr_unlock(MCU_CTRL_MMR0_BASE, 6);
/* Unlock all CTRL_MMR0 module registers */
mmr_unlock(CTRL_MMR0_BASE, 0);
mmr_unlock(CTRL_MMR0_BASE, 1);
mmr_unlock(CTRL_MMR0_BASE, 2);
mmr_unlock(CTRL_MMR0_BASE, 3);
mmr_unlock(CTRL_MMR0_BASE, 6);
mmr_unlock(CTRL_MMR0_BASE, 7);
}
/*
* This uninitialized global variable would normal end up in the .bss section,
* but the .bss is cleared between writing and reading this variable, so move
* it to the .data section.
*/
u32 bootindex __attribute__((section(".data")));
static void store_boot_index_from_rom(void)
{
bootindex = *(u32 *)(CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX);
}
void board_init_f(ulong dummy)
{
#if defined(CONFIG_K3_LOAD_SYSFW) || defined(CONFIG_K3_AM654_DDRSS)
struct udevice *dev;
int ret;
#endif
/*
* Cannot delay this further as there is a chance that
* K3_BOOT_PARAM_TABLE_INDEX can be over written by SPL MALLOC section.
*/
store_boot_index_from_rom();
/* Make all control module registers accessible */
ctrl_mmr_unlock();
#ifdef CONFIG_CPU_V7R
setup_k3_mpu_regions();
#endif
/* Init DM early in-order to invoke system controller */
spl_early_init();
#ifdef CONFIG_K3_LOAD_SYSFW
/*
* Process pinctrl for the serial0 a.k.a. WKUP_UART0 module and continue
* regardless of the result of pinctrl. Do this without probing the
* device, but instead by searching the device that would request the
* given sequence number if probed. The UART will be used by the system
* firmware (SYSFW) image for various purposes and SYSFW depends on us
* to initialize its pin settings.
*/
ret = uclass_find_device_by_seq(UCLASS_SERIAL, 0, true, &dev);
if (!ret)
pinctrl_select_state(dev, "default");
/*
* Load, start up, and configure system controller firmware. Provide
* the U-Boot console init function to the SYSFW post-PM configuration
* callback hook, effectively switching on (or over) the console
* output.
*/
k3_sysfw_loader(preloader_console_init);
#else
/* Prepare console output */
preloader_console_init();
#endif
#ifdef CONFIG_K3_AM654_DDRSS
ret = uclass_get_device(UCLASS_RAM, 0, &dev);
if (ret)
panic("DRAM init failed: %d\n", ret);
#endif
}
u32 spl_boot_mode(const u32 boot_device)
{
#if defined(CONFIG_SUPPORT_EMMC_BOOT)
u32 devstat = readl(CTRLMMR_MAIN_DEVSTAT);
u32 bootmode = (devstat & CTRLMMR_MAIN_DEVSTAT_BOOTMODE_MASK) >>
CTRLMMR_MAIN_DEVSTAT_BOOTMODE_SHIFT;
/* eMMC boot0 mode is only supported for primary boot */
if (bootindex == K3_PRIMARY_BOOTMODE &&
bootmode == BOOT_DEVICE_MMC1)
return MMCSD_MODE_EMMCBOOT;
#endif
/* Everything else use filesystem if available */
#if defined(CONFIG_SPL_FS_FAT) || defined(CONFIG_SPL_FS_EXT4)
return MMCSD_MODE_FS;
#else
return MMCSD_MODE_RAW;
#endif
}
static u32 __get_backup_bootmedia(u32 devstat)
{
u32 bkup_boot = (devstat & CTRLMMR_MAIN_DEVSTAT_BKUP_BOOTMODE_MASK) >>
CTRLMMR_MAIN_DEVSTAT_BKUP_BOOTMODE_SHIFT;
switch (bkup_boot) {
case BACKUP_BOOT_DEVICE_USB:
return BOOT_DEVICE_USB;
case BACKUP_BOOT_DEVICE_UART:
return BOOT_DEVICE_UART;
case BACKUP_BOOT_DEVICE_ETHERNET:
return BOOT_DEVICE_ETHERNET;
case BACKUP_BOOT_DEVICE_MMC2:
{
u32 port = (devstat & CTRLMMR_MAIN_DEVSTAT_BKUP_MMC_PORT_MASK) >>
CTRLMMR_MAIN_DEVSTAT_BKUP_MMC_PORT_SHIFT;
if (port == 0x0)
return BOOT_DEVICE_MMC1;
return BOOT_DEVICE_MMC2;
}
case BACKUP_BOOT_DEVICE_SPI:
return BOOT_DEVICE_SPI;
case BACKUP_BOOT_DEVICE_HYPERFLASH:
return BOOT_DEVICE_HYPERFLASH;
case BACKUP_BOOT_DEVICE_I2C:
return BOOT_DEVICE_I2C;
};
return BOOT_DEVICE_RAM;
}
static u32 __get_primary_bootmedia(u32 devstat)
{
u32 bootmode = (devstat & CTRLMMR_MAIN_DEVSTAT_BOOTMODE_MASK) >>
CTRLMMR_MAIN_DEVSTAT_BOOTMODE_SHIFT;
if (bootmode == BOOT_DEVICE_OSPI || bootmode == BOOT_DEVICE_QSPI)
bootmode = BOOT_DEVICE_SPI;
if (bootmode == BOOT_DEVICE_MMC2) {
u32 port = (devstat & CTRLMMR_MAIN_DEVSTAT_MMC_PORT_MASK) >>
CTRLMMR_MAIN_DEVSTAT_MMC_PORT_SHIFT;
if (port == 0x0)
bootmode = BOOT_DEVICE_MMC1;
} else if (bootmode == BOOT_DEVICE_MMC1) {
u32 port = (devstat & CTRLMMR_MAIN_DEVSTAT_EMMC_PORT_MASK) >>
CTRLMMR_MAIN_DEVSTAT_EMMC_PORT_SHIFT;
if (port == 0x1)
bootmode = BOOT_DEVICE_MMC2;
}
return bootmode;
}
u32 spl_boot_device(void)
{
u32 devstat = readl(CTRLMMR_MAIN_DEVSTAT);
if (bootindex == K3_PRIMARY_BOOTMODE)
return __get_primary_bootmedia(devstat);
else
return __get_backup_bootmedia(devstat);
}
#endif
#ifndef CONFIG_SYSRESET
void reset_cpu(ulong ignored)
{
}
#endif