mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-11 05:42:58 +00:00
c39f44dc6f
Move fsl_ddr_get_spd into common mpc8xxx/ddr/main.c as most boards pretty much do the same thing. The only variations are in how many controllers or DIMMs per controller exist. To make this work we standardize on the names of the SPD_EEPROM_ADDRESS defines based on the use case of the board. We allow boards to override get_spd to either do board specific fixups to the SPD data or deal with any unique behavior of how the SPD eeproms are wired up. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
140 lines
4.1 KiB
C
140 lines
4.1 KiB
C
/*
|
|
* Copyright 2009 Extreme Engineering Solutions, Inc.
|
|
* Copyright 2007-2008 Freescale Semiconductor, Inc.
|
|
*
|
|
* See file CREDITS for list of people who contributed to this
|
|
* project.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
|
|
* MA 02111-1307 USA
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include <asm/fsl_ddr_sdram.h>
|
|
#include <asm/fsl_ddr_dimm_params.h>
|
|
|
|
void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address)
|
|
{
|
|
i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd,
|
|
sizeof(ddr2_spd_eeprom_t));
|
|
}
|
|
|
|
/*
|
|
* There are four board-specific SDRAM timing parameters which must be
|
|
* calculated based on the particular PCB artwork. These are:
|
|
* 1.) CPO (Read Capture Delay)
|
|
* - TIMING_CFG_2 register
|
|
* Source: Calculation based on board trace lengths and
|
|
* chip-specific internal delays.
|
|
* 2.) WR_DATA_DELAY (Write Command to Data Strobe Delay)
|
|
* - TIMING_CFG_2 register
|
|
* Source: Calculation based on board trace lengths.
|
|
* Unless clock and DQ lanes are very different
|
|
* lengths (>2"), this should be set to the nominal value
|
|
* of 1/2 clock delay.
|
|
* 3.) CLK_ADJUST (Clock and Addr/Cmd alignment control)
|
|
* - DDR_SDRAM_CLK_CNTL register
|
|
* Source: Signal Integrity Simulations
|
|
* 4.) 2T Timing on Addr/Ctl
|
|
* - TIMING_CFG_2 register
|
|
* Source: Signal Integrity Simulations
|
|
* Usually only needed with heavy load/very high speed (>DDR2-800)
|
|
*
|
|
* PCB routing on the XPedite5170 is nearly identical to the XPedite5370
|
|
* so we use the XPedite5370 settings as a basis for the XPedite5170.
|
|
*/
|
|
|
|
typedef struct board_memctl_options {
|
|
uint16_t datarate_mhz_low;
|
|
uint16_t datarate_mhz_high;
|
|
uint8_t clk_adjust;
|
|
uint8_t cpo_override;
|
|
uint8_t write_data_delay;
|
|
} board_memctl_options_t;
|
|
|
|
static struct board_memctl_options bopts_ctrl[][2] = {
|
|
{
|
|
/* Controller 0 */
|
|
{
|
|
/* DDR2 600/667 */
|
|
.datarate_mhz_low = 500,
|
|
.datarate_mhz_high = 750,
|
|
.clk_adjust = 5,
|
|
.cpo_override = 8,
|
|
.write_data_delay = 2,
|
|
},
|
|
{
|
|
/* DDR2 800 */
|
|
.datarate_mhz_low = 750,
|
|
.datarate_mhz_high = 850,
|
|
.clk_adjust = 5,
|
|
.cpo_override = 9,
|
|
.write_data_delay = 2,
|
|
},
|
|
},
|
|
{
|
|
/* Controller 1 */
|
|
{
|
|
/* DDR2 600/667 */
|
|
.datarate_mhz_low = 500,
|
|
.datarate_mhz_high = 750,
|
|
.clk_adjust = 5,
|
|
.cpo_override = 7,
|
|
.write_data_delay = 2,
|
|
},
|
|
{
|
|
/* DDR2 800 */
|
|
.datarate_mhz_low = 750,
|
|
.datarate_mhz_high = 850,
|
|
.clk_adjust = 5,
|
|
.cpo_override = 8,
|
|
.write_data_delay = 2,
|
|
},
|
|
},
|
|
};
|
|
|
|
void fsl_ddr_board_options(memctl_options_t *popts,
|
|
dimm_params_t *pdimm,
|
|
unsigned int ctrl_num)
|
|
{
|
|
struct board_memctl_options *bopts = bopts_ctrl[ctrl_num];
|
|
sys_info_t sysinfo;
|
|
int i;
|
|
unsigned int datarate;
|
|
|
|
get_sys_info(&sysinfo);
|
|
datarate = get_ddr_freq(0) / 1000000;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) {
|
|
if ((bopts[i].datarate_mhz_low <= datarate) &&
|
|
(bopts[i].datarate_mhz_high >= datarate)) {
|
|
debug("controller %d:\n", ctrl_num);
|
|
debug(" clk_adjust = %d\n", bopts[i].clk_adjust);
|
|
debug(" cpo = %d\n", bopts[i].cpo_override);
|
|
debug(" write_data_delay = %d\n",
|
|
bopts[i].write_data_delay);
|
|
popts->clk_adjust = bopts[i].clk_adjust;
|
|
popts->cpo_override = bopts[i].cpo_override;
|
|
popts->write_data_delay = bopts[i].write_data_delay;
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Factors to consider for half-strength driver enable:
|
|
* - number of DIMMs installed
|
|
*/
|
|
popts->half_strength_driver_enable = 0;
|
|
}
|