mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-19 11:18:28 +00:00
7da7651251
Arndale board has AX88760, which is USB 2.0 Hub & USB 2.0 Ethernet Combo controller, connected to HSIC Phy of USB host controller via USB3503 hub. This patch uses board specific board_usb_init function to perform reset sequence for USB3503 hub and enables the relevant config options for network to work. Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
122 lines
2.2 KiB
C
122 lines
2.2 KiB
C
/*
|
|
* Copyright (C) 2013 Samsung Electronics
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <usb.h>
|
|
#include <asm/arch/pinmux.h>
|
|
#include <asm/arch/dwmmc.h>
|
|
#include <asm/arch/gpio.h>
|
|
#include <asm/arch/power.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#ifdef CONFIG_USB_EHCI_EXYNOS
|
|
int board_usb_init(int index, enum usb_init_type init)
|
|
{
|
|
struct exynos5_gpio_part1 *gpio = (struct exynos5_gpio_part1 *)
|
|
samsung_get_base_gpio_part1();
|
|
|
|
/* Configure gpios for usb 3503 hub:
|
|
* disconnect, toggle reset and connect
|
|
*/
|
|
s5p_gpio_direction_output(&gpio->d1, 7, 0);
|
|
s5p_gpio_direction_output(&gpio->x3, 5, 0);
|
|
|
|
s5p_gpio_direction_output(&gpio->x3, 5, 1);
|
|
s5p_gpio_direction_output(&gpio->d1, 7, 1);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
int board_init(void)
|
|
{
|
|
gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
|
|
return 0;
|
|
}
|
|
|
|
int dram_init(void)
|
|
{
|
|
int i;
|
|
u32 addr;
|
|
|
|
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
|
|
addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
|
|
gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE);
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
int power_init_board(void)
|
|
{
|
|
set_ps_hold_ctrl();
|
|
return 0;
|
|
}
|
|
|
|
void dram_init_banksize(void)
|
|
{
|
|
int i;
|
|
u32 addr, size;
|
|
|
|
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
|
|
addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
|
|
size = get_ram_size((long *)addr, SDRAM_BANK_SIZE);
|
|
|
|
gd->bd->bi_dram[i].start = addr;
|
|
gd->bd->bi_dram[i].size = size;
|
|
}
|
|
}
|
|
|
|
#ifdef CONFIG_GENERIC_MMC
|
|
int board_mmc_init(bd_t *bis)
|
|
{
|
|
int ret;
|
|
/* dwmmc initializattion for available channels */
|
|
ret = exynos_dwmmc_init(gd->fdt_blob);
|
|
if (ret)
|
|
debug("dwmmc init failed\n");
|
|
|
|
return ret;
|
|
}
|
|
#endif
|
|
|
|
static int board_uart_init(void)
|
|
{
|
|
int err = 0, uart_id;
|
|
|
|
for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) {
|
|
err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE);
|
|
if (err) {
|
|
debug("UART%d not configured\n",
|
|
(uart_id - PERIPH_ID_UART0));
|
|
return err;
|
|
}
|
|
}
|
|
return err;
|
|
}
|
|
|
|
#ifdef CONFIG_BOARD_EARLY_INIT_F
|
|
int board_early_init_f(void)
|
|
{
|
|
int err;
|
|
|
|
err = board_uart_init();
|
|
if (err) {
|
|
debug("UART init failed\n");
|
|
return err;
|
|
}
|
|
return err;
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_DISPLAY_BOARDINFO
|
|
int checkboard(void)
|
|
{
|
|
printf("\nBoard: Arndale\n");
|
|
|
|
return 0;
|
|
}
|
|
#endif
|