mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-14 08:57:58 +00:00
e76cd5d4cf
There were a number of shared files that were using CONFIG_SYS_MPC85xx_DDR_ADDR, or CONFIG_SYS_MPC86xx_DDR_ADDR, and several variants (DDR2, DDR3). A recent patchset added 85xx-specific ones to code which was used by 86xx systems. After reviewing places where these constants were used, and noting that the type definitions of the pointers assigned to point to those addresses were the same, the cleanest approach to fixing this problem was to unify the namespace for the 85xx, 83xx, and 86xx DDR address definitions. This patch does: s/CONFIG_SYS_MPC8.xx_DDR/CONFIG_SYS_MPC8xxx_DDR/g All 85xx, 86xx, and 83xx have been built with this change. Signed-off-by: Andy Fleming <afleming@freescale.com> Tested-by: Andy Fleming <afleming@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
133 lines
3.4 KiB
C
133 lines
3.4 KiB
C
/*
|
|
* Copyright 2008 Freescale Semiconductor, Inc.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* Version 2 as published by the Free Software Foundation.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
|
|
#include <asm/fsl_ddr_sdram.h>
|
|
#include <asm/fsl_ddr_dimm_params.h>
|
|
|
|
void fsl_ddr_board_options(memctl_options_t *popts,
|
|
dimm_params_t *pdimm,
|
|
unsigned int ctrl_num)
|
|
{
|
|
/*
|
|
* Factors to consider for clock adjust:
|
|
* - number of chips on bus
|
|
* - position of slot
|
|
* - DDR1 vs. DDR2?
|
|
* - ???
|
|
*
|
|
* This needs to be determined on a board-by-board basis.
|
|
* 0110 3/4 cycle late
|
|
* 0111 7/8 cycle late
|
|
*/
|
|
popts->clk_adjust = 7;
|
|
|
|
/*
|
|
* Factors to consider for CPO:
|
|
* - frequency
|
|
* - ddr1 vs. ddr2
|
|
*/
|
|
popts->cpo_override = 10;
|
|
|
|
/*
|
|
* Factors to consider for write data delay:
|
|
* - number of DIMMs
|
|
*
|
|
* 1 = 1/4 clock delay
|
|
* 2 = 1/2 clock delay
|
|
* 3 = 3/4 clock delay
|
|
* 4 = 1 clock delay
|
|
* 5 = 5/4 clock delay
|
|
* 6 = 3/2 clock delay
|
|
*/
|
|
popts->write_data_delay = 3;
|
|
|
|
/*
|
|
* Factors to consider for half-strength driver enable:
|
|
* - number of DIMMs installed
|
|
*/
|
|
popts->half_strength_driver_enable = 0;
|
|
}
|
|
|
|
#ifdef CONFIG_SPD_EEPROM
|
|
/*
|
|
* Workaround for hardware errata. An i2c address conflict
|
|
* existed on earlier boards; the workaround moved the DDR
|
|
* SPD from 0x51 to 0x53. So we try and read 0x53 1st, and
|
|
* if that fails, then fall back to reading at 0x51.
|
|
*/
|
|
void get_spd(generic_spd_eeprom_t *spd, u8 i2c_address)
|
|
{
|
|
int ret;
|
|
|
|
#ifdef ALT_SPD_EEPROM_ADDRESS
|
|
if (i2c_address == SPD_EEPROM_ADDRESS) {
|
|
ret = i2c_read(ALT_SPD_EEPROM_ADDRESS, 0, 1, (uchar *)spd,
|
|
sizeof(generic_spd_eeprom_t));
|
|
if (ret == 0)
|
|
return; /* Good data at 0x53 */
|
|
memset(spd, 0, sizeof(generic_spd_eeprom_t));
|
|
}
|
|
#endif
|
|
ret = i2c_read(i2c_address, 0, 1, (uchar *)spd,
|
|
sizeof(generic_spd_eeprom_t));
|
|
if (ret) {
|
|
printf("DDR: failed to read SPD from addr %u\n", i2c_address);
|
|
memset(spd, 0, sizeof(generic_spd_eeprom_t));
|
|
}
|
|
}
|
|
|
|
#else
|
|
/*
|
|
* fixed_sdram init -- doesn't use serial presence detect.
|
|
* Assumes 256MB DDR2 SDRAM SODIMM, without ECC, running at DDR400 speed.
|
|
*/
|
|
phys_size_t fixed_sdram(void)
|
|
{
|
|
volatile ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_MPC8xxx_DDR_ADDR);
|
|
|
|
out_be32(&ddr->cs0_bnds, 0x0000007f);
|
|
out_be32(&ddr->cs1_bnds, 0x008000ff);
|
|
out_be32(&ddr->cs2_bnds, 0x00000000);
|
|
out_be32(&ddr->cs3_bnds, 0x00000000);
|
|
|
|
out_be32(&ddr->cs0_config, 0x80010101);
|
|
out_be32(&ddr->cs1_config, 0x80010101);
|
|
out_be32(&ddr->cs2_config, 0x00000000);
|
|
out_be32(&ddr->cs3_config, 0x00000000);
|
|
|
|
out_be32(&ddr->timing_cfg_3, 0x00000000);
|
|
out_be32(&ddr->timing_cfg_0, 0x00220802);
|
|
out_be32(&ddr->timing_cfg_1, 0x38377322);
|
|
out_be32(&ddr->timing_cfg_2, 0x0fa044C7);
|
|
|
|
out_be32(&ddr->sdram_cfg, 0x4300C000);
|
|
out_be32(&ddr->sdram_cfg_2, 0x24401000);
|
|
|
|
out_be32(&ddr->sdram_mode, 0x23C00542);
|
|
out_be32(&ddr->sdram_mode_2, 0x00000000);
|
|
|
|
out_be32(&ddr->sdram_interval, 0x05080100);
|
|
out_be32(&ddr->sdram_md_cntl, 0x00000000);
|
|
out_be32(&ddr->sdram_data_init, 0x00000000);
|
|
out_be32(&ddr->sdram_clk_cntl, 0x03800000);
|
|
asm("sync;isync;msync");
|
|
udelay(500);
|
|
|
|
#ifdef CONFIG_DDR_ECC
|
|
/* Enable ECC checking */
|
|
out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL | 0x20000000);
|
|
#else
|
|
out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
|
|
#endif
|
|
|
|
return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
|
|
}
|
|
#endif
|