mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-18 17:23:09 +00:00
401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
140 lines
3.6 KiB
C
140 lines
3.6 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* evm.c
|
|
*
|
|
* Copyright (C) 2013, Adeneo Embedded <www.adeneo-embedded.com>
|
|
* Antoine Tenart, <atenart@adeneo-embedded.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <env.h>
|
|
#include <init.h>
|
|
#include <net.h>
|
|
#include <spl.h>
|
|
#include <asm/cache.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/ddr_defs.h>
|
|
#include <asm/arch/hardware.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/arch/mmc_host_def.h>
|
|
#include <asm/arch/mem.h>
|
|
#include <asm/arch/mux.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int board_init(void)
|
|
{
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
#if defined(CONFIG_MTD_RAW_NAND)
|
|
gpmc_init();
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
int board_eth_init(struct bd_info *bis)
|
|
{
|
|
uint8_t mac_addr[6];
|
|
uint32_t mac_hi, mac_lo;
|
|
struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
|
|
|
|
if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
|
|
printf("<ethaddr> not set. Reading from E-fuse\n");
|
|
/* try reading mac address from efuse */
|
|
mac_lo = readl(&cdev->macid0l);
|
|
mac_hi = readl(&cdev->macid0h);
|
|
mac_addr[0] = mac_hi & 0xFF;
|
|
mac_addr[1] = (mac_hi & 0xFF00) >> 8;
|
|
mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
|
|
mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
|
|
mac_addr[4] = mac_lo & 0xFF;
|
|
mac_addr[5] = (mac_lo & 0xFF00) >> 8;
|
|
|
|
if (is_valid_ethaddr(mac_addr))
|
|
eth_env_set_enetaddr("ethaddr", mac_addr);
|
|
else
|
|
printf("Unable to read MAC address. Set <ethaddr>\n");
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_SPL_BUILD
|
|
static struct module_pin_mux mmc_pin_mux[] = {
|
|
{ OFFSET(pincntl157), PULLDOWN_EN | PULLUDDIS | MODE(0x0) },
|
|
{ OFFSET(pincntl158), PULLDOWN_EN | PULLUDEN | MODE(0x0) },
|
|
{ OFFSET(pincntl159), PULLUP_EN | PULLUDDIS | MODE(0x0) },
|
|
{ OFFSET(pincntl160), PULLUP_EN | PULLUDDIS | MODE(0x0) },
|
|
{ OFFSET(pincntl161), PULLUP_EN | PULLUDDIS | MODE(0x0) },
|
|
{ OFFSET(pincntl162), PULLUP_EN | PULLUDDIS | MODE(0x0) },
|
|
{ OFFSET(pincntl163), PULLUP_EN | PULLUDDIS | MODE(0x0) },
|
|
{ -1 },
|
|
};
|
|
|
|
void set_uart_mux_conf(void) {}
|
|
|
|
void set_mux_conf_regs(void)
|
|
{
|
|
configure_module_pin_mux(mmc_pin_mux);
|
|
}
|
|
|
|
/*
|
|
* EMIF Paramters. Refer the EMIF register documentation and the
|
|
* memory datasheet for details. This is for 796 MHz.
|
|
*/
|
|
#define EMIF_TIM1 0x1779C9FE
|
|
#define EMIF_TIM2 0x50608074
|
|
#define EMIF_TIM3 0x009F857F
|
|
#define EMIF_SDREF 0x10001841
|
|
#define EMIF_SDCFG 0x62A73832
|
|
#define EMIF_PHYCFG 0x00000110
|
|
static const struct emif_regs ddr3_emif_regs = {
|
|
.sdram_config = EMIF_SDCFG,
|
|
.ref_ctrl = EMIF_SDREF,
|
|
.sdram_tim1 = EMIF_TIM1,
|
|
.sdram_tim2 = EMIF_TIM2,
|
|
.sdram_tim3 = EMIF_TIM3,
|
|
.emif_ddr_phy_ctlr_1 = EMIF_PHYCFG,
|
|
};
|
|
|
|
static const struct cmd_control ddr3_ctrl = {
|
|
.cmd0csratio = 0x100,
|
|
.cmd0iclkout = 0x001,
|
|
.cmd1csratio = 0x100,
|
|
.cmd1iclkout = 0x001,
|
|
.cmd2csratio = 0x100,
|
|
.cmd2iclkout = 0x001,
|
|
};
|
|
|
|
/* These values are obtained from the CCS app */
|
|
#define RD_DQS_GATE (0x1B3)
|
|
#define RD_DQS (0x35)
|
|
#define WR_DQS (0x93)
|
|
static struct ddr_data ddr3_data = {
|
|
.datardsratio0 = ((RD_DQS<<10) | (RD_DQS<<0)),
|
|
.datawdsratio0 = ((WR_DQS<<10) | (WR_DQS<<0)),
|
|
.datawiratio0 = ((0x20<<10) | 0x20<<0),
|
|
.datagiratio0 = ((0x20<<10) | 0x20<<0),
|
|
.datafwsratio0 = ((RD_DQS_GATE<<10) | (RD_DQS_GATE<<0)),
|
|
.datawrsratio0 = (((WR_DQS+0x40)<<10) | ((WR_DQS+0x40)<<0)),
|
|
};
|
|
|
|
static const struct dmm_lisa_map_regs evm_lisa_map_regs = {
|
|
.dmm_lisa_map_0 = 0x00000000,
|
|
.dmm_lisa_map_1 = 0x00000000,
|
|
.dmm_lisa_map_2 = 0x80640300,
|
|
.dmm_lisa_map_3 = 0xC0640320,
|
|
};
|
|
|
|
void sdram_init(void)
|
|
{
|
|
/*
|
|
* Pass in our DDR3 config information and that we have 2 EMIFs to
|
|
* configure.
|
|
*/
|
|
config_ddr(&ddr3_data, &ddr3_ctrl, &ddr3_emif_regs,
|
|
&evm_lisa_map_regs, 2);
|
|
}
|
|
#endif /* CONFIG_SPL_BUILD */
|