mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-08 22:24:32 +00:00
10e959a1ca
MYS-6ULX is single board computer (SBC) comes with eMMC or NAND based on imx6ULL SoC from NXP and provision for expansion board. This commit adds support only for SBC with NAND. CPU: Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz) CPU: Commercial temperature grade (0C to 95C) at 45C Reset cause: WDOG Model: MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND Board: MYiR MYS-6ULX 6ULL Single Board Computer DRAM: 256 MiB NAND: 256 MiB MMC: FSL_SDHC: 0 In: serial@2020000 Out: serial@2020000 Err: serial@2020000 Net: FEC0 Working: - Eth0 - MMC/SD - NAND - UART 1 - USB host Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
52 lines
1.3 KiB
Text
52 lines
1.3 KiB
Text
How to use U-Boot on MYiR MYS-6ULX Single Board Computer
|
|
--------------------------------------------------------
|
|
|
|
- Configure and build U-Boot for MYS-6ULX iMX6ULL:
|
|
|
|
$ make mrproper
|
|
$ make myir_mys_6ulx_defconfig
|
|
$ make
|
|
|
|
This will generate SPL and u-boot-dtb.img images.
|
|
|
|
Boot from MMC/SD:
|
|
- The SPL and u-boot-dtb.img images need to be flashed into the micro SD card:
|
|
|
|
$ sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
|
|
$ sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69; sync
|
|
|
|
- Boot mode settings:
|
|
|
|
Boot switch position: SW1 -> 0
|
|
SW2 -> 1
|
|
SW3 -> 0
|
|
SW4 -> 1
|
|
|
|
Boot from NAND:
|
|
- Boot the board using SD/MMC or Serial download and load the SPL into memory
|
|
either from SD/MMC or TFTP.
|
|
|
|
Default MTD layout is 512k(spl),1m(uboot),1m(uboot-dup),-(ubi)
|
|
|
|
Flash SPL to NAND from SD/MMC,
|
|
|
|
$ ext4load mmc 0:2 $loadaddr SPL
|
|
$ nand erase.part spl
|
|
$ nandbcb init $loadaddr 0x0 $filesize
|
|
|
|
Flash u-boot proper to NAND from SD/MMC,
|
|
|
|
$ ext4load mmc 0:2 $loadaddr u-boot-dtb.img
|
|
$ nand erase.part uboot
|
|
$ nand write $loadaddr uboot $filesize
|
|
|
|
- Boot mode settings:
|
|
|
|
Boot switch position: SW1 -> 1
|
|
SW2 -> 0
|
|
SW3 -> 0
|
|
SW4 -> 1
|
|
|
|
- Connect the Serial cable to UART0 and the PC for the console.
|
|
|
|
- Reset the board using and U-Boot should boot from NAND.
|