u-boot/board/eric/eric.c
2005-10-13 16:45:02 +02:00

195 lines
5.9 KiB
C

/*
* (C) Copyright 2001
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <i2c.h>
#include "eric.h"
#include <asm/processor.h>
#define PPC405GP_GPIO0_OR 0xef600700 /* GPIO Output */
#define PPC405GP_GPIO0_TCR 0xef600704 /* GPIO Three-State Control */
#define PPC405GP_GPIO0_ODR 0xef600718 /* GPIO Open Drain */
#define PPC405GP_GPIO0_IR 0xef60071c /* GPIO Input */
int board_early_init_f (void)
{
/*-------------------------------------------------------------------------+
| Interrupt controller setup for the ERIC board.
| Note: IRQ 0-15 405GP internally generated; active high; level sensitive
| IRQ 16 405GP internally generated; active low; level sensitive
| IRQ 17-24 RESERVED
| IRQ 25 (EXT IRQ 0) FLASH; active low; level sensitive
| IRQ 26 (EXT IRQ 1) PHY ; active low; level sensitive
| IRQ 27 (EXT IRQ 2) HOST FAIL, active low; level sensitive
| indicates NO Power or HOST RESET active
| check GPIO7 (HOST RESET#) and GPIO8 (NO Power#)
| for real IRQ source
| IRQ 28 (EXT IRQ 3) HOST; active high; level sensitive
| IRQ 29 (EXT IRQ 4) PCI INTC#; active low; level sensitive
| IRQ 30 (EXT IRQ 5) PCI INTB#; active low; level sensitive
| IRQ 31 (EXT IRQ 6) PCI INTA#; active low; level sensitive
| -> IRQ6 Pin is NOW GPIO23 and can be activateted by setting
| PPC405GP_GPIO0_TCR Bit 0 = 1 (driving the output as defined in PPC405GP_GPIO0_OR,
| else tristate)
| Note for ERIC board:
| An interrupt taken for the HOST (IRQ 28) indicates that
| the HOST wrote a "1" to one of the following locations
| - VGA CRT_GPIO0 (if R1216 is loaded)
| - VGA CRT_GPIO1 (if R1217 is loaded)
|
+-------------------------------------------------------------------------*/
mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */
mtdcr (uicer, 0x00000000); /* disable all ints */
mtdcr (uiccr, 0x00000000); /* set all SMI to be non-critical */
mtdcr (uicpr, 0xFFFFFF88); /* set int polarities; IRQ3 to 1 */
mtdcr (uictr, 0x10000000); /* set int trigger levels, UART0 is EDGE */
mtdcr (uicvcr, 0x00000001); /* set vect base=0,INT0 highest priority */
mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */
mtdcr (cntrl0, 0x00002000); /* set IRQ6 as GPIO23 to generate an interrupt request to the PCP2PCI bridge */
out32 (PPC405GP_GPIO0_OR, 0x60000000); /*fixme is SMB_INT high or low active??; IRQ6 is GPIO23 output */
out32 (PPC405GP_GPIO0_TCR, 0x7E400000);
return 0;
}
/* ------------------------------------------------------------------------- */
/*
* Check Board Identity:
*/
int checkboard (void)
{
char *s = getenv ("serial#");
char *e;
puts ("Board: ");
if (!s || strncmp (s, "ERIC", 9)) {
puts ("### No HW ID - assuming ERIC");
} else {
for (e = s; *e; ++e) {
if (*e == ' ')
break;
}
for (; s < e; ++s) {
putc (*s);
}
}
putc ('\n');
return (0);
}
/* ------------------------------------------------------------------------- */
/* ------------------------------------------------------------------------- */
/* ------------------------------------------------------------------------- */
/*
initdram(int board_type) reads EEPROM via I2c. EEPROM contains all of
the necessary info for SDRAM controller configuration
*/
/* ------------------------------------------------------------------------- */
/* ------------------------------------------------------------------------- */
long int initdram (int board_type)
{
#ifndef CONFIG_ERIC
int i;
unsigned char datain[128];
int TotalSize;
#endif
#ifdef CONFIG_ERIC
/*
* we have no EEPROM on ERIC
* so let init.S do the init job for SDRAM
* and simply return 32MByte here
*/
return (CFG_SDRAM_SIZE * 1024 * 1024);
#else
/* Read Serial Presence Detect Information */
for (i = 0; i < 128; i++)
datain[i] = 127;
i2c_send (SPD_EEPROM_ADDRESS, 0, 1, datain, 128);
printf ("\nReading DIMM...\n");
#if 0
for (i = 0; i < 128; i++) {
printf ("%d=0x%x ", i, datain[i]);
if (((i + 1) % 10) == 0)
printf ("\n");
}
printf ("\n");
#endif
/*****************************/
/* Retrieve interesting data */
/*****************************/
/* size of a SDRAM bank */
/* Number of bytes per side / number of banks per side */
if (datain[31] == 0x08)
TotalSize = 32;
else if (datain[31] == 0x10)
TotalSize = 64;
else {
printf ("IIC READ ERROR!!!\n");
TotalSize = 32;
}
/* single-sided DIMM or double-sided DIMM? */
if (datain[5] != 1) {
/* double-sided DIMM => SDRAM banks 0..3 are valid */
printf ("double-sided DIMM\n");
TotalSize *= 2;
}
/* else single-sided DIMM => SDRAM bank 0 and bank 2 are valid */
else {
printf ("single-sided DIMM\n");
}
/* return size in Mb unit => *(1024*1024) */
return (TotalSize * 1024 * 1024);
#endif
}
/* ------------------------------------------------------------------------- */
int testdram (void)
{
/* TODO: XXX XXX XXX */
printf ("test: xxx MB - ok\n");
return (0);
}
/* ------------------------------------------------------------------------- */