u-boot/board/keymile/km_arm/km_arm.c
Holger Brunck 37605c466d arm/km: adapt bootcounter evaluation
The bootcounter (stored in the RAM) is not enough protected with the 4 Bytes
BOOTCOUNT_MAGIC against bit errors due to short power loss or holding a system
in RESET. It has been seen, that the bootcounter value has been changed due to
a bit flip on a system holding in RESET, but the BOOTCOUNT_MAGIC was still valid.

A bit pattern with 4000 bytes (after BOOTCOUNT_MAGIC) has been implemented,
which should be enough to detect a bit error.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2011-11-03 22:56:23 +01:00

523 lines
11 KiB
C

/*
* (C) Copyright 2009
* Marvell Semiconductor <www.marvell.com>
* Prafulla Wadaskar <prafulla@marvell.com>
*
* (C) Copyright 2009
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* (C) Copyright 2010
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301 USA
*/
#include <common.h>
#include <i2c.h>
#include <nand.h>
#include <netdev.h>
#include <miiphy.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/kirkwood.h>
#include <asm/arch/mpp.h>
#include "../common/common.h"
DECLARE_GLOBAL_DATA_PTR;
/*
* BOCO FPGA definitions
*/
#define BOCO 0x10
#define REG_CTRL_H 0x02
#define MASK_WRL_UNITRUN 0x01
#define MASK_RBX_PGY_PRESENT 0x40
#define REG_IRQ_CIRQ2 0x2d
#define MASK_RBI_DEFECT_16 0x01
/* Multi-Purpose Pins Functionality configuration */
u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
MPP3_NF_IO5,
MPP4_NF_IO6,
MPP5_NF_IO7,
MPP6_SYSRST_OUTn,
MPP7_PEX_RST_OUTn,
#if defined(CONFIG_SOFT_I2C)
MPP8_GPIO, /* SDA */
MPP9_GPIO, /* SCL */
#endif
#if defined(CONFIG_HARD_I2C)
MPP8_TW_SDA,
MPP9_TW_SCK,
#endif
MPP10_UART0_TXD,
MPP11_UART0_RXD,
MPP12_GPO, /* Reserved */
MPP13_UART1_TXD,
MPP14_UART1_RXD,
MPP15_GPIO, /* Not used */
MPP16_GPIO, /* Not used */
MPP17_GPIO, /* Reserved */
MPP18_NF_IO0,
MPP19_NF_IO1,
MPP20_GPIO,
MPP21_GPIO,
MPP22_GPIO,
MPP23_GPIO,
MPP24_GPIO,
MPP25_GPIO,
MPP26_GPIO,
MPP27_GPIO,
MPP28_GPIO,
MPP29_GPIO,
MPP30_GPIO,
MPP31_GPIO,
MPP32_GPIO,
MPP33_GPIO,
MPP34_GPIO, /* CDL1 (input) */
MPP35_GPIO, /* CDL2 (input) */
MPP36_GPIO, /* MAIN_IRQ (input) */
MPP37_GPIO, /* BOARD_LED */
MPP38_GPIO, /* Piggy3 LED[1] */
MPP39_GPIO, /* Piggy3 LED[2] */
MPP40_GPIO, /* Piggy3 LED[3] */
MPP41_GPIO, /* Piggy3 LED[4] */
MPP42_GPIO, /* Piggy3 LED[5] */
MPP43_GPIO, /* Piggy3 LED[6] */
MPP44_GPIO, /* Piggy3 LED[7], BIST_EN_L */
MPP45_GPIO, /* Piggy3 LED[8] */
MPP46_GPIO, /* Reserved */
MPP47_GPIO, /* Reserved */
MPP48_GPIO, /* Reserved */
MPP49_GPIO, /* SW_INTOUTn */
0
};
#if defined(CONFIG_MGCOGE3UN)
/*
* Wait for startup OK from mgcoge3ne
*/
int startup_allowed(void)
{
unsigned char buf;
/*
* Read CIRQ16 bit (bit 0)
*/
if (i2c_read(BOCO, REG_IRQ_CIRQ2, 1, &buf, 1) != 0)
printf("%s: Error reading Boco\n", __func__);
else
if ((buf & MASK_RBI_DEFECT_16) == MASK_RBI_DEFECT_16)
return 1;
return 0;
}
#endif
#if (defined(CONFIG_MGCOGE3UN)|defined(CONFIG_PORTL2))
/*
* These two boards have always ethernet present. Its connected to the mv
* switch.
*/
int ethernet_present(void)
{
return 1;
}
#else
int ethernet_present(void)
{
uchar buf;
int ret = 0;
if (i2c_read(BOCO, REG_CTRL_H, 1, &buf, 1) != 0) {
printf("%s: Error reading Boco\n", __func__);
return -1;
}
if ((buf & MASK_RBX_PGY_PRESENT) == MASK_RBX_PGY_PRESENT)
ret = 1;
return ret;
}
#endif
int initialize_unit_leds(void)
{
/*
* Init the unit LEDs per default they all are
* ok apart from bootstat
*/
uchar buf;
if (i2c_read(BOCO, REG_CTRL_H, 1, &buf, 1) != 0) {
printf("%s: Error reading Boco\n", __func__);
return -1;
}
buf |= MASK_WRL_UNITRUN;
if (i2c_write(BOCO, REG_CTRL_H, 1, &buf, 1) != 0) {
printf("%s: Error writing Boco\n", __func__);
return -1;
}
return 0;
}
#if defined(CONFIG_BOOTCOUNT_LIMIT)
void set_bootcount_addr(void)
{
uchar buf[32];
unsigned int bootcountaddr;
bootcountaddr = gd->ram_size - BOOTCOUNT_ADDR;
sprintf((char *)buf, "0x%x", bootcountaddr);
setenv("bootcountaddr", (char *)buf);
}
#endif
int misc_init_r(void)
{
char *str;
int mach_type;
str = getenv("mach_type");
if (str != NULL) {
mach_type = simple_strtoul(str, NULL, 10);
printf("Overwriting MACH_TYPE with %d!!!\n", mach_type);
gd->bd->bi_arch_number = mach_type;
}
#if defined(CONFIG_MGCOGE3UN)
char *wait_for_ne;
wait_for_ne = getenv("waitforne");
if (wait_for_ne != NULL) {
if (strcmp(wait_for_ne, "true") == 0) {
int cnt = 0;
int abort = 0;
puts("NE go: ");
while (startup_allowed() == 0) {
if (tstc()) {
(void) getc(); /* consume input */
abort = 1;
break;
}
udelay(200000);
cnt++;
if (cnt == 5)
puts("wait\b\b\b\b");
if (cnt == 10) {
cnt = 0;
puts(" \b\b\b\b");
}
}
if (abort == 1)
printf("\nAbort waiting for ne\n");
else
puts("OK\n");
}
}
#endif
initialize_unit_leds();
set_km_env();
#if defined(CONFIG_BOOTCOUNT_LIMIT)
set_bootcount_addr();
#endif
return 0;
}
int board_early_init_f(void)
{
u32 tmp;
kirkwood_mpp_conf(kwmpp_config);
/*
* The FLASH_GPIO_PIN switches between using a
* NAND or a SPI FLASH. Set this pin on start
* to NAND mode.
*/
tmp = readl(KW_GPIO0_BASE);
writel(tmp | FLASH_GPIO_PIN , KW_GPIO0_BASE);
tmp = readl(KW_GPIO0_BASE + 4);
writel(tmp & (~FLASH_GPIO_PIN) , KW_GPIO0_BASE + 4);
#if defined(CONFIG_SOFT_I2C)
/* init the GPIO for I2C Bitbang driver */
kw_gpio_set_valid(KM_KIRKWOOD_SDA_PIN, 1);
kw_gpio_set_valid(KM_KIRKWOOD_SCL_PIN, 1);
kw_gpio_direction_output(KM_KIRKWOOD_SDA_PIN, 0);
kw_gpio_direction_output(KM_KIRKWOOD_SCL_PIN, 0);
#endif
#if defined(CONFIG_SYS_EEPROM_WREN)
kw_gpio_set_valid(KM_KIRKWOOD_ENV_WP, 38);
kw_gpio_direction_output(KM_KIRKWOOD_ENV_WP, 1);
#endif
#if defined(CONFIG_KM_RECONFIG_XLX)
/* trigger the reconfiguration of the xilinx fpga */
kw_gpio_set_valid(KM_XLX_PROGRAM_B_PIN, 1);
kw_gpio_direction_output(KM_XLX_PROGRAM_B_PIN, 0);
kw_gpio_direction_input(KM_XLX_PROGRAM_B_PIN);
#endif
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
return 0;
}
#if defined(CONFIG_CMD_SF)
int do_spi_toggle(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
u32 tmp;
if (argc < 2)
return cmd_usage(cmdtp);
if ((strcmp(argv[1], "off") == 0)) {
printf("SPI FLASH disabled, NAND enabled\n");
/* Multi-Purpose Pins Functionality configuration */
kwmpp_config[0] = MPP0_NF_IO2;
kwmpp_config[1] = MPP1_NF_IO3;
kwmpp_config[2] = MPP2_NF_IO4;
kwmpp_config[3] = MPP3_NF_IO5;
kirkwood_mpp_conf(kwmpp_config);
tmp = readl(KW_GPIO0_BASE);
writel(tmp | FLASH_GPIO_PIN , KW_GPIO0_BASE);
} else if ((strcmp(argv[1], "on") == 0)) {
printf("SPI FLASH enabled, NAND disabled\n");
/* Multi-Purpose Pins Functionality configuration */
kwmpp_config[0] = MPP0_SPI_SCn;
kwmpp_config[1] = MPP1_SPI_MOSI;
kwmpp_config[2] = MPP2_SPI_SCK;
kwmpp_config[3] = MPP3_SPI_MISO;
kirkwood_mpp_conf(kwmpp_config);
tmp = readl(KW_GPIO0_BASE);
writel(tmp & (~FLASH_GPIO_PIN) , KW_GPIO0_BASE);
} else {
return cmd_usage(cmdtp);
}
return 0;
}
U_BOOT_CMD(
spitoggle, 2, 0, do_spi_toggle,
"En-/disable SPI FLASH access",
"<on|off> - Enable (on) or disable (off) SPI FLASH access\n"
);
#endif
int dram_init(void)
{
/* dram_init must store complete ramsize in gd->ram_size */
/* Fix this */
gd->ram_size = get_ram_size((void *)kw_sdram_bar(0),
kw_sdram_bs(0));
return 0;
}
void dram_init_banksize(void)
{
int i;
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
gd->bd->bi_dram[i].start = kw_sdram_bar(i);
gd->bd->bi_dram[i].size = get_ram_size((long *)kw_sdram_bar(i),
kw_sdram_bs(i));
}
}
#if (defined(CONFIG_MGCOGE3UN)|defined(CONFIG_PORTL2))
#define PHY_LED_SEL 0x18
#define PHY_LED0_LINK (0x5)
#define PHY_LED1_ACT (0x8<<4)
#define PHY_LED2_INT (0xe<<8)
#define PHY_SPEC_CTRL 0x1c
#define PHY_RGMII_CLK_STABLE (0x1<<10)
#define PHY_CLSA (0x1<<1)
/* Configure and enable MV88E3018 PHY */
void reset_phy(void)
{
char *name = "egiga0";
unsigned short reg;
if (miiphy_set_current_dev(name))
return;
/* RGMII clk transition on data stable */
if (miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL, &reg) != 0)
printf("Error reading PHY spec ctrl reg\n");
if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL,
reg | PHY_RGMII_CLK_STABLE | PHY_CLSA) != 0)
printf("Error writing PHY spec ctrl reg\n");
/* leds setup */
if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL,
PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT) != 0)
printf("Error writing PHY LED reg\n");
/* reset the phy */
miiphy_reset(name, CONFIG_PHY_BASE_ADR);
}
#else
/* Configure and enable MV88E1118 PHY on the piggy*/
void reset_phy(void)
{
char *name = "egiga0";
if (miiphy_set_current_dev(name))
return;
/* reset the phy */
miiphy_reset(name, CONFIG_PHY_BASE_ADR);
}
#endif
#if defined(CONFIG_HUSH_INIT_VAR)
int hush_init_var(void)
{
ivm_read_eeprom();
return 0;
}
#endif
#if defined(CONFIG_BOOTCOUNT_LIMIT)
const ulong patterns[] = { 0x00000000,
0xFFFFFFFF,
0xFF00FF00,
0x0F0F0F0F,
0xF0F0F0F0};
const ulong NBR_OF_PATTERNS = sizeof(patterns)/sizeof(*patterns);
const ulong OFFS_PATTERN = 3;
const ulong REPEAT_PATTERN = 1000;
void bootcount_store(ulong a)
{
volatile ulong *save_addr;
volatile ulong size = 0;
int i;
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
size += gd->bd->bi_dram[i].size;
}
save_addr = (ulong*)(size - BOOTCOUNT_ADDR);
writel(a, save_addr);
writel(BOOTCOUNT_MAGIC, &save_addr[1]);
for (i = 0; i < REPEAT_PATTERN; i++)
writel(patterns[i % NBR_OF_PATTERNS],
&save_addr[i+OFFS_PATTERN]);
}
ulong bootcount_load(void)
{
volatile ulong *save_addr;
volatile ulong size = 0;
ulong counter = 0;
int i, tmp;
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
size += gd->bd->bi_dram[i].size;
}
save_addr = (ulong*)(size - BOOTCOUNT_ADDR);
counter = readl(&save_addr[0]);
/* Is the counter reliable, check in the big pattern for bit errors */
for (i = 0; (i < REPEAT_PATTERN) && (counter != 0); i++) {
tmp = readl(&save_addr[i+OFFS_PATTERN]);
if (tmp != patterns[i % NBR_OF_PATTERNS])
counter = 0;
}
return counter;
}
#endif
#if defined(CONFIG_SOFT_I2C)
void set_sda(int state)
{
I2C_ACTIVE;
I2C_SDA(state);
}
void set_scl(int state)
{
I2C_SCL(state);
}
int get_sda(void)
{
I2C_TRISTATE;
return I2C_READ;
}
int get_scl(void)
{
return kw_gpio_get_value(KM_KIRKWOOD_SCL_PIN) ? 1 : 0;
}
#endif
#if defined(CONFIG_POST)
#define KM_POST_EN_L 44
#define POST_WORD_OFF 8
int post_hotkeys_pressed(void)
{
return !kw_gpio_get_value(KM_POST_EN_L);
}
ulong post_word_load(void)
{
volatile void* addr = (void *) (gd->ram_size - BOOTCOUNT_ADDR + POST_WORD_OFF);
return in_le32(addr);
}
void post_word_store(ulong value)
{
volatile void* addr = (void *) (gd->ram_size - BOOTCOUNT_ADDR + POST_WORD_OFF);
out_le32(addr, value);
}
int arch_memory_test_prepare(u32 *vstart, u32 *size, phys_addr_t *phys_offset)
{
*vstart = CONFIG_SYS_SDRAM_BASE;
/* we go up to relocation plus a 1 MB margin */
*size = CONFIG_SYS_TEXT_BASE - (1<<20);
return 0;
}
#endif
#if defined(CONFIG_SYS_EEPROM_WREN)
int eeprom_write_enable(unsigned dev_addr, int state)
{
kw_gpio_set_value(KM_KIRKWOOD_ENV_WP, !state);
return !kw_gpio_get_value(KM_KIRKWOOD_ENV_WP);
}
#endif