u-boot/include/configs/draco.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

81 lines
1.8 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2013 Siemens Schweiz AG
* (C) Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* Based on:
* U-Boot file:/include/configs/am335x_evm.h
*
* Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
*/
#ifndef __CONFIG_DRACO_H
#define __CONFIG_DRACO_H
#define CONFIG_SIEMENS_MACH_TYPE MACH_TYPE_DRACO
#include "siemens-am33x-common.h"
#define DDR_PLL_FREQ 303
#define BOARD_DFU_BUTTON_GPIO 27 /* Use as default */
#define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */
#define CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \
"button_dfu0=27\0" \
"led0=103,1,0\0" \
"led1=64,0,1\0"
/* Physical Memory Map */
#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */
/* I2C Configuration */
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define EEPROM_ADDR_DDR3 0x90
#define EEPROM_ADDR_CHIP 0x120
#define CONFIG_PHY_SMSC
#define CONFIG_FACTORYSET
/* Define own nand partitions */
#define CONFIG_ENV_RANGE (4 * CONFIG_SYS_ENV_SECT_SIZE)
#ifndef CONFIG_SPL_BUILD
/* Default env settings */
#define CONFIG_EXTRA_ENV_SETTINGS \
"hostname=draco\0" \
"ubi_off=2048\0"\
"nand_img_size=0x400000\0" \
"optargs=\0" \
"preboot=draco_led 0\0" \
CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \
CONFIG_ENV_SETTINGS_V2 \
CONFIG_ENV_SETTINGS_NAND_V2
#ifndef CONFIG_RESTORE_FLASH
/* set to negative value for no autoboot */
#define CONFIG_BOOTCOMMAND \
"if dfubutton; then " \
"run dfu_start; " \
"reset; " \
"fi;" \
"run nand_boot;" \
"run nand_boot_backup;" \
"reset;"
#else
#define CONFIG_BOOTCOMMAND \
"setenv autoload no; " \
"dhcp; " \
"if tftp 80000000 debrick.scr; then " \
"source 80000000; " \
"fi"
#endif
#endif /* CONFIG_SPL_BUILD */
#endif /* ! __CONFIG_DRACO_H */