mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-13 06:42:56 +00:00
401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
122 lines
2.5 KiB
C
122 lines
2.5 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* (C) Copyright 2016 Nexell
|
|
* Hyunseok, Jung <hsjung@nexell.co.kr>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <command.h>
|
|
#include <asm/system.h>
|
|
#include <asm/cache.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/sections.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/nexell.h>
|
|
#include <asm/arch/clk.h>
|
|
#include <asm/arch/reset.h>
|
|
#include <asm/arch/tieoff.h>
|
|
#include <cpu_func.h>
|
|
#include <linux/delay.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#ifndef CONFIG_ARCH_CPU_INIT
|
|
#error must be define the macro "CONFIG_ARCH_CPU_INIT"
|
|
#endif
|
|
|
|
void s_init(void)
|
|
{
|
|
}
|
|
|
|
static void cpu_soc_init(void)
|
|
{
|
|
/*
|
|
* NOTE> ALIVE Power Gate must enable for Alive register access.
|
|
* must be clear wfi jump address
|
|
*/
|
|
writel(1, ALIVEPWRGATEREG);
|
|
writel(0xFFFFFFFF, SCR_ARM_SECOND_BOOT);
|
|
|
|
/* write 0xf0 on alive scratchpad reg for boot success check */
|
|
writel(readl(SCR_SIGNAGURE_READ) | 0xF0, (SCR_SIGNAGURE_SET));
|
|
|
|
/* set l2 cache tieoff */
|
|
nx_tieoff_set(NX_TIEOFF_CORTEXA9MP_TOP_QUADL2C_L2RET1N_0, 1);
|
|
nx_tieoff_set(NX_TIEOFF_CORTEXA9MP_TOP_QUADL2C_L2RET1N_1, 1);
|
|
}
|
|
|
|
#ifdef CONFIG_PL011_SERIAL
|
|
static void serial_device_init(void)
|
|
{
|
|
char dev[10];
|
|
int id;
|
|
|
|
sprintf(dev, "nx-uart.%d", CONFIG_CONS_INDEX);
|
|
id = RESET_ID_UART0 + CONFIG_CONS_INDEX;
|
|
|
|
struct clk *clk = clk_get((const char *)dev);
|
|
|
|
/* reset control: Low active ___|--- */
|
|
nx_rstcon_setrst(id, RSTCON_ASSERT);
|
|
udelay(10);
|
|
nx_rstcon_setrst(id, RSTCON_NEGATE);
|
|
udelay(10);
|
|
|
|
/* set clock */
|
|
clk_disable(clk);
|
|
clk_set_rate(clk, CONFIG_PL011_CLOCK);
|
|
clk_enable(clk);
|
|
}
|
|
#endif
|
|
|
|
int arch_cpu_init(void)
|
|
{
|
|
flush_dcache_all();
|
|
cpu_soc_init();
|
|
clk_init();
|
|
|
|
if (IS_ENABLED(CONFIG_PL011_SERIAL))
|
|
serial_device_init();
|
|
|
|
return 0;
|
|
}
|
|
|
|
#if defined(CONFIG_DISPLAY_CPUINFO)
|
|
int print_cpuinfo(void)
|
|
{
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
void reset_cpu(ulong ignored)
|
|
{
|
|
void *clkpwr_reg = (void *)PHY_BASEADDR_CLKPWR;
|
|
const u32 sw_rst_enb_bitpos = 3;
|
|
const u32 sw_rst_enb_mask = 1 << sw_rst_enb_bitpos;
|
|
const u32 sw_rst_bitpos = 12;
|
|
const u32 sw_rst_mask = 1 << sw_rst_bitpos;
|
|
int pwrcont = 0x224;
|
|
int pwrmode = 0x228;
|
|
u32 read_value;
|
|
|
|
read_value = readl((void *)(clkpwr_reg + pwrcont));
|
|
|
|
read_value &= ~sw_rst_enb_mask;
|
|
read_value |= 1 << sw_rst_enb_bitpos;
|
|
|
|
writel(read_value, (void *)(clkpwr_reg + pwrcont));
|
|
writel(sw_rst_mask, (void *)(clkpwr_reg + pwrmode));
|
|
}
|
|
|
|
void enable_caches(void)
|
|
{
|
|
/* Enable D-cache. I-cache is already enabled in start.S */
|
|
dcache_enable();
|
|
}
|
|
|
|
#if defined(CONFIG_ARCH_MISC_INIT)
|
|
int arch_misc_init(void)
|
|
{
|
|
return 0;
|
|
}
|
|
#endif /* CONFIG_ARCH_MISC_INIT */
|