u-boot/include/configs/udoo.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

93 lines
2.4 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2013 Freescale Semiconductor, Inc.
*
* Configuration settings for Udoo board.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include "mx6_common.h"
#include "imx6_spl.h"
/* Provide the MACH_TYPE value that the vendor kernel requires. */
#define CONFIG_MACH_TYPE 4800
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (2 * SZ_1M)
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART2_BASE
/* SATA Configs */
#ifdef CONFIG_CMD_SATA
#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
#define CONFIG_LBA48
#endif
/* Network support */
#define CONFIG_FEC_MXC
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 6
#define CONFIG_SYS_MEMTEST_START 0x10000000
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)
/* MMC Configuration */
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define CONFIG_EXTRA_ENV_SETTINGS \
"console=ttymxc1,115200\0" \
"fdt_high=0xffffffff\0" \
"initrd_high=0xffffffff\0" \
"fdtfile=undefined\0" \
"fdt_addr=0x18000000\0" \
"fdt_addr_r=0x18000000\0" \
"ip_dyn=yes\0" \
"mmcdev=0\0" \
"mmcrootfstype=ext4\0" \
"findfdt="\
"if test ${board_rev} = MX6Q; then " \
"setenv fdtfile imx6q-udoo.dtb; fi; " \
"if test ${board_rev} = MX6DL; then " \
"setenv fdtfile imx6dl-udoo.dtb; fi; " \
"if test ${fdtfile} = undefined; then " \
"echo WARNING: Could not determine dtb to use; fi\0" \
"kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
"pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
"ramdisk_addr_r=0x13000000\0" \
"scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
BOOTENV
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
func(SATA, sata, 0) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
/* Physical Memory Map */
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* Environment organization */
#define CONFIG_SYS_MMC_ENV_DEV 0
#endif /* __CONFIG_H * */