u-boot/include/configs/vinco.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

104 lines
3.1 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Configuration settings for the VInCo platform.
*
* Based on the settings for the SAMA5-EK board
* Copyright (C) 2014 Atmel
* Bo Shen <voice.shen@atmel.com>
* Copyright (C) 2015 Free Electrons
* Gregory CLEMENT gregory.clement@free-electrons.com
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include "at91-sama5_common.h"
/* The value in the common file is too far away for the VInCo platform */
/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE 0xfc00c000
#define CONFIG_USART_ID 30
/* Timer */
#define CONFIG_SYS_TIMER_COUNTER 0xfc06863c
/* SDRAM */
#define CONFIG_SYS_SDRAM_BASE 0x20000000
#define CONFIG_SYS_SDRAM_SIZE 0x4000000
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
/* SerialFlash */
#ifdef CONFIG_CMD_SF
#define CONFIG_ATMEL_SPI0
#define CONFIG_SPI_FLASH_STMICRO
#endif
/* MMC */
#ifdef CONFIG_CMD_MMC
#define CONFIG_GENERIC_ATMEL_MCI
#define ATMEL_BASE_MMCI 0xfc000000
#define CONFIG_SYS_MMC_CLK_OD 500000
/* For generating MMC partitions */
#endif
/* USB device */
/* Ethernet Hardware */
#define CONFIG_PHY_SMSC
#define CONFIG_MACB
#define CONFIG_RMII
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_MACB_SEARCH_PHY
#ifdef CONFIG_SPI_BOOT
/* bootstrap + u-boot + env + linux in serial flash */
/* Use our own mapping for the VInCo platform */
/* Update the bootcommand according to our mapping for the VInCo platform */
#undef CONFIG_BOOTCOMMAND
#define CONFIG_BOOTCOMMAND "mmc dev 0 0;" \
"mmc read ${loadaddr} ${k_offset} ${k_blksize};" \
"mmc read ${oftaddr} ${dtb_offset} ${dtb_blksize};" \
"bootz ${loadaddr} - ${oftaddr}"
#define CONFIG_EXTRA_ENV_SETTINGS \
"kernel_start=0x20000\0" \
"kernel_size=0x800000\0" \
"mmcblksize=0x200\0" \
"oftaddr=0x21000000\0" \
"loadaddr=0x22000000\0" \
"update_uboot=tftp ${loadaddr} u-boot.bin;sf probe 0;" \
"sf erase 0x20000 0x4B000; sf write ${loadaddr} 0x20000 0x4B000\0" \
"create_partition=setexpr dtb_start ${kernel_start} + 0x400000;" \
"setexpr rootfs_start ${kernel_start} + ${kernel_size};" \
"setenv partitions 'name=kernel,size=${kernel_size}," \
"start=${kernel_start};name=rootfs,size=-';" \
"gpt write mmc 0 ${partitions} \0"\
"f2blk_size=setexpr fileblksize ${filesize} / ${mmcblksize};" \
"setexpr fileblksize ${fileblksize} + 1\0" \
"store_kernel=tftp ${loadaddr} zImage; run f2blk_size;" \
"setexpr k_blksize ${fileblksize};" \
"setexpr k_offset ${kernel_start} / ${mmcblksize};" \
"mmc write ${fileaddr} ${k_offset} ${fileblksize}\0" \
"store_dtb=tftp ${loadaddr} at91-vinco.dtb; run f2blk_size;" \
"setexpr dtb_blksize ${fileblksize};" \
"setexpr dtb_offset ${dtb_start} / ${mmcblksize};" \
"mmc write ${fileaddr} ${dtb_offset} ${fileblksize}\0" \
"store_rootfs=tftp ${loadaddr} vinco-gateway-image-vinco.ext4;" \
"setexpr rootfs_offset ${rootfs_start} / ${mmcblksize};" \
"mmc write ${fileaddr} ${rootfs_offset} ${fileblksize}\0" \
"bootdelay=0\0"
#endif
#endif