u-boot/include/configs/imx8mq_evk.h
Tom Rini b70b2bed1a Convert CONFIG_IMX_BOOTAUX et al to Kconfig
This converts the following to Kconfig:
   CONFIG_IMX_BOOTAUX
   CONFIG_IMX_THERMAL

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-12 14:18:17 -05:00

111 lines
2.9 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2018 NXP
*/
#ifndef __IMX8M_EVK_H
#define __IMX8M_EVK_H
#include <linux/sizes.h>
#include <linux/stringify.h>
#include <asm/arch/imx-regs.h>
#define CONFIG_SYS_BOOTM_LEN (64 * SZ_1M)
#define CONFIG_SPL_MAX_SIZE (124 * 1024)
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300
#ifdef CONFIG_SPL_BUILD
/*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
#define CONFIG_SPL_STACK 0x187FF0
#define CONFIG_SPL_BSS_START_ADDR 0x00180000
#define CONFIG_SPL_BSS_MAX_SIZE 0x2000 /* 8 KB */
#define CONFIG_SYS_SPL_MALLOC_START 0x42200000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 /* 512 KB */
#define CONFIG_SYS_SPL_PTE_RAM_BASE 0x41580000
/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
#define CONFIG_MALLOC_F_ADDR 0x182000
/* For RAW image gives a error info not panic */
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
#undef CONFIG_DM_MMC
#define CONFIG_POWER_PFUZE100
#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
#endif
#define CONFIG_REMAKE_ELF
/* ENET Config */
/* ENET1 */
#if defined(CONFIG_CMD_NET)
#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 0
#define FEC_QUIRK_ENET_MAC
#define IMX_FEC_BASE 0x30BE0000
#endif
#ifndef CONFIG_SPL_BUILD
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
func(MMC, mmc, 1) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#endif
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
BOOTENV \
"scriptaddr=0x43500000\0" \
"kernel_addr_r=0x40880000\0" \
"image=Image\0" \
"console=ttymxc0,115200\0" \
"fdt_addr=0x43000000\0" \
"boot_fdt=try\0" \
"fdt_file=imx8mq-evk.dtb\0" \
"initrd_addr=0x43800000\0" \
"bootm_size=0x10000000\0" \
"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
/* Link Definitions */
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x80000
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC2 */
#define CONFIG_SYS_SDRAM_BASE 0x40000000
#define PHYS_SDRAM 0x40000000
#define PHYS_SDRAM_SIZE 0xC0000000 /* 3GB DDR */
#define CONFIG_MXC_UART_BASE UART1_BASE_ADDR
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 1024
#define CONFIG_SYS_MAXARGS 64
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
#define CONFIG_MXC_GPIO
#define CONFIG_OF_SYSTEM_SETUP
#endif