u-boot/arch/arm/mach-omap2/am33xx/Kconfig
Tom Rini 8457d023b8 global: Remove extraneous DM_ETH imply/select
We only need to enable DM_ETH if we have a networking driver. All
networking drivers depend on DM_ETH being enabled, and their selection
ensures DM_ETH will be enabled.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-07 16:04:16 -05:00

325 lines
6.9 KiB
Text

if TI816X
config TARGET_TI816X_EVM
bool "Support ti816x_evm"
help
This option specifies support for the TI8168 EVM development platform
with PG2.0 silicon and DDR3 DRAM.
endif
if TI814X
config TARGET_TI814X_EVM
bool "Support ti814x_evm"
help
This option specifies support for the TI8148
EVM development platform.
endif
if AM33XX
config AM33XX_CHILISOM
bool
select SUPPORT_SPL
choice
prompt "AM33xx board select"
config TARGET_AM335X_EVM
bool "Support am335x_evm"
select BOARD_LATE_INIT
select DM
select DM_GPIO
select DM_SERIAL
select TI_I2C_BOARD_DETECT
select SUPPORT_EXTENSION_SCAN
imply CMD_DM
imply SPL_DM
imply SPL_DM_SEQ_ALIAS
imply SPL_ENV_SUPPORT
imply SPL_FS_EXT4
imply SPL_FS_FAT
imply SPL_GPIO
imply SPL_I2C
imply SPL_LIBCOMMON_SUPPORT
imply SPL_LIBDISK_SUPPORT
imply SPL_LIBGENERIC_SUPPORT
imply SPL_MMC
imply SPL_NAND_SUPPORT
imply SPL_OF_LIBFDT
imply SPL_POWER
imply SPL_SEPARATE_BSS
imply SPL_SERIAL
imply SPL_SYS_MALLOC_SIMPLE
imply SPL_WATCHDOG
imply SPL_YMODEM_SUPPORT
help
This option specifies support for the AM335x
GP and HS EVM development platforms. The AM335x
GP EVM is a standalone test, development, and
evaluation module system that enables developers
to write software and develop hardware around
an AM335x processor subsystem.
config TARGET_AM335X_BALTOS
bool "Support am335x_baltos"
select BOARD_LATE_INIT
select DM
select DM_GPIO
select DM_SERIAL
imply CMD_DM
config TARGET_AM335X_IGEP003X
bool "Support am335x_igep003x"
select BOARD_LATE_INIT
select DM
select DM_GPIO
select DM_SERIAL
imply CMD_DM
config TARGET_AM335X_SHC
bool "Support am335x based shc board from bosch"
select BOARD_LATE_INIT
select DM
select DM_GPIO
select DM_SERIAL
imply CMD_DM
imply CMD_SPL
config TARGET_AM335X_GUARDIAN
bool "Support am335x based guardian board from bosch"
select BOARD_LATE_INIT
select DM
select DM_SERIAL
select DM_GPIO
select VIDEO
select PANEL_HX8238D
config TARGET_AM335X_SL50
bool "Support am335x_sl50"
select BOARD_LATE_INIT
select DM
select DM_GPIO
select DM_SERIAL
imply CMD_DM
config TARGET_BRXRE1
bool "Support BRXRE1"
select BOARD_LATE_INIT
config TARGET_BRSMARC1
bool "Support BRSMARC1"
select BOARD_LATE_INIT
config TARGET_BRPPT1
bool "Support BRPPT1"
select BOARD_LATE_INIT
config TARGET_CHILIBOARD
bool "Grinn chiliBoard"
select AM33XX_CHILISOM
select BOARD_LATE_INIT
select DM
select DM_SERIAL
imply CMD_DM
config TARGET_DRACO
bool "Support draco"
select BOARD_LATE_INIT
select DM
select DM_GPIO
select DM_SERIAL
select FACTORYSET
imply CMD_DM
config TARGET_ETAMIN
bool "Support etamin"
select BOARD_LATE_INIT
select DM
select DM_GPIO
select DM_SERIAL
select FACTORYSET
imply CMD_DM
config TARGET_PCM051
bool "Support pcm051"
select DM
select DM_GPIO
select DM_SERIAL
imply CMD_DM
config TARGET_PHYCORE_AM335X_R2
bool "Support phyCORE AM335X R2"
select DM
select DM_GPIO
select DM_SERIAL
imply CMD_DM
config TARGET_PXM2
bool "Support pxm2"
select BOARD_LATE_INIT
select DM
select DM_GPIO
select DM_SERIAL
select FACTORYSET
imply CMD_DM
config TARGET_RASTABAN
bool "Support rastaban"
select BOARD_LATE_INIT
select DM
select DM_GPIO
select DM_SERIAL
select FACTORYSET
imply CMD_DM
config TARGET_RUT
bool "Support rut"
select BOARD_LATE_INIT
select DM
select DM_GPIO
select DM_SERIAL
select FACTORYSET
imply CMD_DM
config TARGET_THUBAN
bool "Support thuban"
select BOARD_LATE_INIT
select DM
select DM_GPIO
select DM_SERIAL
select FACTORYSET
imply CMD_DM
config TARGET_PDU001
bool "Support PDU001"
select DM
select DM_SERIAL
imply SPL_SEPARATE_BSS
imply CMD_DM
help
Support for PDU001 platform developed by EETS GmbH.
The PDU001 is a processor and display unit developed around
the Computing-Module m2 from bytes at work AG.
endchoice
config CLOCK_SYNTHESIZER
bool "CDCE913 and CDCEL913 clock synthesizer support"
help
The CDCE913 and CDCEL913 devices are modular PLL-based, low cost,
high performance , programmable clock synthesizers. They generate
up to 3 output clocks from a single input frequency. Each output can
be programmed for any clock-frequency.
config CLK_SYNTHESIZER_I2C_ADDR
hex "Clock synthesizer i2c bus address"
depends on CLOCK_SYNTHESIZER
default 0x65
endif
if AM43XX
choice
prompt "AM43xx board select"
config TARGET_AM43XX_EVM
bool "Support am43xx_evm"
select BOARD_LATE_INIT
select TI_I2C_BOARD_DETECT
imply DM_I2C
imply DM_SPI
imply DM_SPI_FLASH
imply SPL_ENV_SUPPORT
imply SPL_FS_EXT4
imply SPL_FS_FAT
imply SPL_GPIO
imply SPL_I2C
imply SPL_LIBCOMMON_SUPPORT
imply SPL_LIBDISK_SUPPORT
imply SPL_LIBGENERIC_SUPPORT
imply SPL_MMC
imply SPL_NAND_SUPPORT
imply SPL_POWER
imply SPL_SERIAL
imply SPL_WATCHDOG
imply SPL_YMODEM_SUPPORT
help
This option specifies support for the AM43xx
GP and HS EVM development platforms.The AM437x
GP EVM is a standalone test, development, and
evaluation module system that enables developers
to write software and develop hardware around
an AM43xx processor subsystem.
config TARGET_CM_T43
bool "Support cm_t43"
endchoice
config SPL_RTC_DDR_SUPPORT
bool
depends on SPL
prompt "Enable RTC-DDR ONLY Support"
help
If you want RTC-DDR ONLY Support, say Y. RTC Only with DDR in
self-refresh mode is a special power saving mode where in all
the other voltages are turned off apart from the RTC domain and DDR.
So only RTC is alive and ticking and one can program it to wake
up after a predetermined period. Once RTC alarm fires, the PMIC
powers up all the voltage domains. U-Boot takes a special path
as the DDR has contents is in self-refresh and restore path is
followed.
endif
if AM43XX || AM33XX
config PUB_ROM_DATA_SIZE
hex "Size in bytes of the L3 SRAM reserved by ROM to store data"
default 0x8400
help
During the device boot, the public ROM uses the top of
the public L3 OCMC RAM to store r/w data like stack,
heap, globals etc. When the ROM is copying the boot
image from the boot media into memory, the image must
not spill over into this area. This value can be used
during compile time to determine the maximum size of a
boot image. Once the ROM transfers control to the boot
image, this area is no longer used, and can be reclaimed
for run time use by the boot image.
endif
config AM335X_USB0
bool "Static mode configuration for USB0 in SPL"
depends on AM33XX && SPL_MUSB_NEW && !SPL_OF_CONTROL
choice
prompt "USB0 port configuration"
depends on AM335X_USB0
config AM335X_USB0_HOST
bool "Port is used in host mode"
config AM335X_USB0_PERIPHERAL
bool "Port is used in peripheral mode"
endchoice
config AM335X_USB1
bool "Static mode configuration for USB1 in SPL"
depends on AM33XX && SPL_MUSB_NEW && !SPL_OF_CONTROL
choice
prompt "USB1 port configuration"
depends on AM335X_USB1
config AM335X_USB1_HOST
bool "Port is used in host mode"
config AM335X_USB1_PERIPHERAL
bool "Port is used in peripheral mode"
endchoice