u-boot/include/configs/at91-sama5_common.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

73 lines
1.8 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Common part of configuration settings for the AT91 SAMA5 board.
*
* Copyright (C) 2015 Atmel Corporation
* Josh Wu <josh.wu@atmel.com>
*/
#ifndef __AT91_SAMA5_COMMON_H
#define __AT91_SAMA5_COMMON_H
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SKIP_LOWLEVEL_INIT
#endif
/* general purpose I/O */
#ifndef CONFIG_DM_GPIO
#define CONFIG_AT91_GPIO
#endif
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
/*
* Command line configuration.
*/
#ifdef CONFIG_SD_BOOT
#ifdef CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV 0
#endif
#define CONFIG_BOOTCOMMAND "if test ! -n ${dtb_name}; then " \
"setenv dtb_name at91-${board_name}.dtb; " \
"fi; " \
"fatload mmc 0:1 0x21000000 ${dtb_name}; " \
"fatload mmc 0:1 0x22000000 zImage; " \
"bootz 0x22000000 - 0x21000000"
#else
#ifdef CONFIG_NAND_BOOT
/* u-boot env in nand flash */
#define CONFIG_BOOTCOMMAND "nand read 0x21000000 0x180000 0x80000;" \
"nand read 0x22000000 0x200000 0x600000;" \
"bootz 0x22000000 - 0x21000000"
#elif CONFIG_SPI_BOOT
/* u-boot env in serial flash, by default is bus 0 and cs 0 */
#define CONFIG_BOOTCOMMAND "sf probe 0; " \
"sf read 0x21000000 0x60000 0xc000; " \
"sf read 0x22000000 0x6c000 0x394000; " \
"bootz 0x22000000 - 0x21000000"
#elif CONFIG_QSPI_BOOT
#define CONFIG_BOOTCOMMAND "sf probe 0; " \
"sf read 0x21000000 0x180000 0x80000; " \
"sf read 0x22000000 0x200000 0x600000; " \
"bootz 0x22000000 - 0x21000000"
#endif
#endif
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
#endif