u-boot/include/configs/ls1012a_common.h
Yuantian Tang b584510f07 armv8: configs: ls1012a: correct the generic timer frequency
On ls1012a soc, core clock source frequency is fixed at 100Mhz.
Generic timer frequency is core clock source divided by 4, which
is 25Mhz.

Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27 08:39:49 -07:00

117 lines
3 KiB
C

/*
* Copyright 2016 Freescale Semiconductor
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __LS1012A_COMMON_H
#define __LS1012A_COMMON_H
#define CONFIG_FSL_LAYERSCAPE
#define CONFIG_GICV2
#include <asm/arch/config.h>
#include <asm/arch/stream_id_lsch2.h>
#define CONFIG_SUPPORT_RAW_INITRD
#define CONFIG_DISPLAY_BOARDINFO_LATE
#define CONFIG_SYS_TEXT_BASE 0x40100000
#define CONFIG_SYS_CLK_FREQ 125000000
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_DDR_BLOCK2_BASE 0x880000000ULL
/* Generic Timer Definitions */
#define COUNTER_FREQUENCY 25000000 /* 25MHz */
/* CSU */
#define CONFIG_LAYERSCAPE_NS_ACCESS
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024)
/*SPI device */
#ifdef CONFIG_QSPI_BOOT
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
#define CONFIG_SYS_FMAN_FW_ADDR 0x400d0000
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_CS 0
#define CONFIG_ENV_SPI_MAX_HZ 1000000
#define CONFIG_ENV_SPI_MODE 0x03
#define CONFIG_SPI_FLASH_SPANSION
#define CONFIG_FSL_SPI_INTERFACE
#define CONFIG_SF_DATAFLASH
#define CONFIG_FSL_QSPI
#define QSPI0_AMBA_BASE 0x40000000
#define CONFIG_SPI_FLASH_SPANSION
#define FSL_QSPI_FLASH_SIZE SZ_64M
#define FSL_QSPI_FLASH_NUM 2
/*
* Environment
*/
#define CONFIG_ENV_OVERWRITE
#define CONFIG_ENV_SIZE 0x40000 /* 256KB */
#define CONFIG_ENV_OFFSET 0x200000 /* 2MB */
#define CONFIG_ENV_SECT_SIZE 0x40000
#endif
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_serial_clock())
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_SYS_HZ 1000
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
"verify=no\0" \
"loadaddr=0x80100000\0" \
"kernel_addr=0x100000\0" \
"fdt_high=0xffffffffffffffff\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0xa00000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
#define CONFIG_BOOTCOMMAND "sf probe 0:0; sf read $kernel_load "\
"$kernel_start $kernel_size && "\
"bootm $kernel_load"
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING 1
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#define CONFIG_PANIC_HANG
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#include <asm/arch/soc.h>
#endif /* __LS1012A_COMMON_H */