u-boot/include/configs/cm-bf527.h
Mike Frysinger 821ad16fa9 Blackfin: move CONFIG_BFIN_CPU to board config.mk
The CONFIG_BFIN_CPU option is largely used in the build system, so move
it out of the board config.h and into the board config.mk.  It'd be nice
to keep everything in the config.h, but the patch to extract that value
early was rejected.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02 16:00:38 -04:00

139 lines
3.4 KiB
C

/*
* U-boot - Configuration file for CM-BF527 board
*/
#ifndef __CONFIG_CM_BF527_H__
#define __CONFIG_CM_BF527_H__
#include <asm/config-pre.h>
/*
* Processor Settings
*/
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA
/*
* Clock Settings
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
*/
/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ 25000000
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
/* 1 = CLKIN / 2 */
#define CONFIG_CLKIN_HALF 0
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
/* 1 = bypass PLL */
#define CONFIG_PLL_BYPASS 0
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
/* Values can range from 0-63 (where 0 means 64) */
#define CONFIG_VCO_MULT 21
/* CCLK_DIV controls the core clock divider */
/* Values can be 1, 2, 4, or 8 ONLY */
#define CONFIG_CCLK_DIV 1
/* SCLK_DIV controls the system clock divider */
/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 4
/* Decrease core voltage */
#define CONFIG_VR_CTL_VAL (VLEV_120 | CLKBUFOE | FREQ_1000)
/*
* Memory Settings
*/
#define CONFIG_MEM_ADD_WDTH 9
#define CONFIG_MEM_SIZE 32
#define CONFIG_EBIU_SDRRC_VAL 0x3f8
#define CONFIG_EBIU_SDGCTL_VAL 0x9111cd
#define CONFIG_EBIU_AMGCTL_VAL (AMBEN_ALL)
#define CONFIG_EBIU_AMBCTL0_VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3)
#define CONFIG_EBIU_AMBCTL1_VAL (B3WAT_7 | B3RAT_11 | B3HT_2 | B3ST_3 | B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3)
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
#define CONFIG_SYS_MALLOC_LEN (128 * 1024)
/*
* NAND Settings
* (can't be used sametime as ethernet)
*/
/* #define CONFIG_BFIN_NFC */
#ifdef CONFIG_BFIN_NFC
#define CONFIG_BFIN_NFC_CTL_VAL 0x0033
#define CONFIG_SYS_NAND_BASE 0 /* not actually used */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define NAND_MAX_CHIPS 1
#define CONFIG_CMD_NAND
#endif
/*
* Network Settings
*/
#if !defined(__ADSPBF522__) && !defined(__ADSPBF523__) && \
!defined(__ADSPBF524__) && !defined(__ADSPBF525__) && !defined(CONFIG_BFIN_NFC)
#define ADI_CMDS_NETWORK 1
#define CONFIG_BFIN_MAC
#define CONFIG_RMII
#define CONFIG_NETCONSOLE 1
#define CONFIG_NET_MULTI 1
#endif
#define CONFIG_HOSTNAME cm-bf527
/* Uncomment next line to use fixed MAC address */
/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
/*
* Flash Settings
*/
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
#define CONFIG_SYS_FLASH_BASE 0x20000000
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 67
/*
* Env Storage Settings
*/
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR 0x20008000
#define CONFIG_ENV_OFFSET 0x8000
#define CONFIG_ENV_SIZE 0x8000
#define CONFIG_ENV_SECT_SIZE 0x8000
#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
/*
* I2C Settings
*/
#define CONFIG_BFIN_TWI_I2C 1
#define CONFIG_HARD_I2C 1
/*
* Misc Settings
*/
#define CONFIG_BAUDRATE 115200
#define CONFIG_MISC_INIT_R
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 0
#define CONFIG_BOOTCOMMAND "run flashboot"
#define FLASHBOOT_ENV_SETTINGS \
"flashboot=flread 20040000 1000000 300000;" \
"bootm 0x1000000\0"
/*
* Pull in common ADI header for remaining command/environment setup
*/
#include <configs/bfin_adi_common.h>
#endif