mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-13 16:37:30 +00:00
6f6b7cfa89
This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini <trini@konsulko.com>
126 lines
3.6 KiB
C
126 lines
3.6 KiB
C
/*
|
|
* Config file for Compulab CM-T54 board
|
|
*
|
|
* Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
|
|
*
|
|
* Author: Dmitry Lifshitz <lifshitz@compulab.co.il>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __CONFIG_CM_T54_H
|
|
#define __CONFIG_CM_T54_H
|
|
|
|
#define CONFIG_CM_T54
|
|
#define CONFIG_DRAM_2G
|
|
|
|
#include <configs/ti_omap5_common.h>
|
|
|
|
/* EEPROM related defines */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_I2C_EEPROM_BUS 0
|
|
|
|
/* Enable SD/MMC CD and WP GPIOs */
|
|
#define OMAP_HSMMC_USE_GPIO
|
|
|
|
/* UART setup */
|
|
#define CONFIG_SYS_NS16550_COM4 UART4_BASE
|
|
|
|
/* MMC ENV related defines */
|
|
#undef CONFIG_ENV_OFFSET
|
|
#undef CONFIG_ENV_SIZE
|
|
|
|
#define CONFIG_SYS_MMC_ENV_DEV 1 /* SLOT2: eMMC(1) */
|
|
#define CONFIG_SYS_MMC_ENV_PART 0
|
|
#define CONFIG_ENV_OFFSET 0xc0000 /* (in bytes) 768 KB */
|
|
#define CONFIG_ENV_SIZE (16 << 10) /* 16 KB */
|
|
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
|
|
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
|
|
|
|
/* Enhance our eMMC support / experience. */
|
|
#define CONFIG_HSMMC2_8BIT
|
|
#define CONFIG_SUPPORT_EMMC_BOOT
|
|
|
|
/* SATA Boot related defines */
|
|
#define CONFIG_SPL_SATA_BOOT_DEVICE 0
|
|
#define CONFIG_SYS_SATA_FAT_BOOT_PARTITION 1
|
|
|
|
#define CONFIG_SCSI_AHCI_PLAT
|
|
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
|
|
#define CONFIG_SYS_SCSI_MAX_LUN 1
|
|
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
|
|
CONFIG_SYS_SCSI_MAX_LUN)
|
|
/* USB UHH support options */
|
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
|
|
|
#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 76 /* HSIC2 HUB #RESET */
|
|
#define CONFIG_OMAP_EHCI_PHY3_RESET_GPIO 83 /* HSIC3 ETH #RESET */
|
|
|
|
/* Enabled commands */
|
|
|
|
/* EEPROM */
|
|
#define CONFIG_ENV_EEPROM_IS_ON_I2C
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
|
|
#define CONFIG_SYS_EEPROM_SIZE 256
|
|
|
|
/* USB Networking options */
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#undef CONFIG_SYS_AUTOLOAD
|
|
#undef CONFIG_EXTRA_ENV_SETTINGS
|
|
#undef CONFIG_BOOTCOMMAND
|
|
|
|
#define CONFIG_SYS_AUTOLOAD "no"
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
DEFAULT_LINUX_BOOT_ENV \
|
|
"baudrate=115200\0" \
|
|
"bootdelay=3\0" \
|
|
"autoload=no\0" \
|
|
"bootscr=bootscr.img\0" \
|
|
"fdtfile=omap5-sbc-t54.dtb\0" \
|
|
"kernel=zImage-cm-t54\0" \
|
|
"ramdisk=ramdisk-cm-t54.img\0" \
|
|
"console=ttyO3\0" \
|
|
"ramdisksize=16384\0" \
|
|
"mmcdev=0\0" \
|
|
"mmcroot=/dev/mmcblk1p2\0" \
|
|
"mmcargs=setenv bootargs console=${console} " \
|
|
"root=${mmcroot} rw rootwait\0" \
|
|
"ramroot=/dev/ram0\0" \
|
|
"ramargs=setenv bootargs console=${console} " \
|
|
"root=${ramroot} ramdisk_size=${ramdisksize} rw\0" \
|
|
"mmcloadkernel=load mmc ${mmcdev} ${loadaddr} ${kernel}\0" \
|
|
"mmcloadfdt=load mmc ${mmcdev} ${fdtaddr} ${fdtfile}\0" \
|
|
"mmcloadramdisk=load mmc ${mmcdev} ${rdaddr} ${ramdisk}\0" \
|
|
"mmcloadbootscript=load mmc ${mmcdev} ${loadaddr} ${bootsrc}\0" \
|
|
"mmcbootscript=echo Running bootscript from mmc${mmcdev}...; " \
|
|
"source ${loadaddr}\0" \
|
|
"mmcbootlinux=echo Booting from mmc${mmcdev} ...; " \
|
|
"bootz ${loadaddr} ${rdaddr} ${fdtaddr}\0" \
|
|
"mmcboot=if mmc dev ${mmcdev} && mmc rescan; then " \
|
|
"if run mmcloadbootscript; " \
|
|
"then run mmcbootscript; " \
|
|
"fi; " \
|
|
"if run mmcloadkernel; then " \
|
|
"if run mmcloadfdt; then " \
|
|
"if run mmcloadramdisk; then " \
|
|
"run ramargs; " \
|
|
"run mmcbootlinux; " \
|
|
"fi; " \
|
|
"run mmcargs; " \
|
|
"setenv rdaddr - ; " \
|
|
"run mmcbootlinux; " \
|
|
"fi; " \
|
|
"fi; " \
|
|
"fi;\0"
|
|
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"bootcmd=run mmcboot || setenv mmcdev 1; setenv mmcroot /dev/mmcblk0p2; run mmcboot;"
|
|
|
|
#endif /* __CONFIG_CM_T54_H */
|