mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-30 08:31:03 +00:00
4d7d0e2e78
Update the sdmmc2 node for eMMC support on eval board stm32mp157c-ev1. - update slew-rate for pin configuration - update "vqmmc-supply" - remove "st,sig-dir" - add mandatory "pinctrl-names" - add "mmc-ddr-3_3v" This patch solve the eMMC detection issue for command "mmc dev 1". Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
206 lines
2.9 KiB
Text
206 lines
2.9 KiB
Text
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
|
|
/*
|
|
* Copyright : STMicroelectronics 2018
|
|
*/
|
|
|
|
#include <dt-bindings/clock/stm32mp1-clksrc.h>
|
|
#include "stm32mp157-u-boot.dtsi"
|
|
#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
|
|
|
|
/ {
|
|
aliases {
|
|
i2c3 = &i2c4;
|
|
mmc0 = &sdmmc1;
|
|
mmc1 = &sdmmc2;
|
|
};
|
|
|
|
config {
|
|
u-boot,boot-led = "heartbeat";
|
|
u-boot,error-led = "error";
|
|
st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
|
|
st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led {
|
|
red {
|
|
label = "error";
|
|
gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
status = "okay";
|
|
};
|
|
|
|
blue {
|
|
default-state = "on";
|
|
};
|
|
};
|
|
};
|
|
|
|
&clk_hse {
|
|
st,digbypass;
|
|
};
|
|
|
|
&i2c4 {
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
|
|
&i2c4_pins_a {
|
|
u-boot,dm-pre-reloc;
|
|
pins {
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
};
|
|
|
|
&pmic {
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
|
|
&rcc {
|
|
st,clksrc = <
|
|
CLK_MPU_PLL1P
|
|
CLK_AXI_PLL2P
|
|
CLK_MCU_PLL3P
|
|
CLK_PLL12_HSE
|
|
CLK_PLL3_HSE
|
|
CLK_PLL4_HSE
|
|
CLK_RTC_LSE
|
|
CLK_MCO1_DISABLED
|
|
CLK_MCO2_DISABLED
|
|
>;
|
|
|
|
st,clkdiv = <
|
|
1 /*MPU*/
|
|
0 /*AXI*/
|
|
0 /*MCU*/
|
|
1 /*APB1*/
|
|
1 /*APB2*/
|
|
1 /*APB3*/
|
|
1 /*APB4*/
|
|
2 /*APB5*/
|
|
23 /*RTC*/
|
|
0 /*MCO1*/
|
|
0 /*MCO2*/
|
|
>;
|
|
|
|
st,pkcs = <
|
|
CLK_CKPER_HSE
|
|
CLK_FMC_ACLK
|
|
CLK_QSPI_ACLK
|
|
CLK_ETH_DISABLED
|
|
CLK_SDMMC12_PLL4P
|
|
CLK_DSI_DSIPLL
|
|
CLK_STGEN_HSE
|
|
CLK_USBPHY_HSE
|
|
CLK_SPI2S1_PLL3Q
|
|
CLK_SPI2S23_PLL3Q
|
|
CLK_SPI45_HSI
|
|
CLK_SPI6_HSI
|
|
CLK_I2C46_HSI
|
|
CLK_SDMMC3_PLL4P
|
|
CLK_USBO_USBPHY
|
|
CLK_ADC_CKPER
|
|
CLK_CEC_LSE
|
|
CLK_I2C12_HSI
|
|
CLK_I2C35_HSI
|
|
CLK_UART1_HSI
|
|
CLK_UART24_HSI
|
|
CLK_UART35_HSI
|
|
CLK_UART6_HSI
|
|
CLK_UART78_HSI
|
|
CLK_SPDIF_PLL4P
|
|
CLK_FDCAN_PLL4Q
|
|
CLK_SAI1_PLL3Q
|
|
CLK_SAI2_PLL3Q
|
|
CLK_SAI3_PLL3Q
|
|
CLK_SAI4_PLL3Q
|
|
CLK_RNG1_LSI
|
|
CLK_RNG2_LSI
|
|
CLK_LPTIM1_PCLK1
|
|
CLK_LPTIM23_PCLK3
|
|
CLK_LPTIM45_LSE
|
|
>;
|
|
|
|
/* VCO = 1300.0 MHz => P = 650 (CPU) */
|
|
pll1: st,pll@0 {
|
|
cfg = < 2 80 0 0 0 PQR(1,0,0) >;
|
|
frac = < 0x800 >;
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
|
|
/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
|
|
pll2: st,pll@1 {
|
|
cfg = < 2 65 1 0 0 PQR(1,1,1) >;
|
|
frac = < 0x1400 >;
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
|
|
/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
|
|
pll3: st,pll@2 {
|
|
cfg = < 1 33 1 16 36 PQR(1,1,1) >;
|
|
frac = < 0x1a04 >;
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
|
|
/* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
|
|
pll4: st,pll@3 {
|
|
cfg = < 3 98 5 7 7 PQR(1,1,1) >;
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
};
|
|
|
|
&sdmmc1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&sdmmc1_b4_pins_a {
|
|
u-boot,dm-spl;
|
|
pins {
|
|
u-boot,dm-spl;
|
|
};
|
|
};
|
|
|
|
&sdmmc1_dir_pins_a {
|
|
u-boot,dm-spl;
|
|
pins1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
pins2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
};
|
|
|
|
&sdmmc2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&sdmmc2_b4_pins_a {
|
|
u-boot,dm-spl;
|
|
pins1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
pins2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
};
|
|
|
|
&sdmmc2_d47_pins_a {
|
|
u-boot,dm-spl;
|
|
pins {
|
|
u-boot,dm-spl;
|
|
};
|
|
};
|
|
|
|
&uart4 {
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
|
|
&uart4_pins_a {
|
|
u-boot,dm-pre-reloc;
|
|
pins1 {
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
pins2 {
|
|
u-boot,dm-pre-reloc;
|
|
/* pull-up on rx to avoid floating level */
|
|
bias-pull-up;
|
|
};
|
|
};
|