u-boot/include/configs/mx53ppd.h
Ian Ray b186cfa1a3 board: ge: pass rtc_status via device tree
Pass rtc_status via the device tree, instead of on kernel command line.
Additionally, the 2038 mitigation is reported, if applied successfully.

Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-01-07 10:26:56 +01:00

212 lines
6.2 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2011 Freescale Semiconductor, Inc.
* Jason Liu <r64343@freescale.com>
*
* Configuration settings for Freescale MX53 low cost board.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/arch/imx-regs.h>
#define CONSOLE_DEV "ttymxc0"
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_SYS_FSL_CLK
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_REVISION_TAG
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART1_BASE
/* Eth Configs */
#define CONFIG_FEC_MXC
#define IMX_FEC_BASE FEC_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1F
/* USB Configs */
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_USB_ETHER_MCS7830
#define CONFIG_USB_ETHER_SMSC95XX
#define CONFIG_MXC_USB_PORT 1
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#define CONFIG_SYS_RTC_BUS_NUM 2
#define CONFIG_SYS_I2C_RTC_ADDR 0x30
/* I2C Configs */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
/* PMIC Controller */
#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_DIALOG_POWER
#define CONFIG_POWER_FSL
#define CONFIG_POWER_FSL_MC13892
#define CONFIG_SYS_DIALOG_PMIC_I2C_ADDR 0x48
#define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x8
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_BAUDRATE 115200
/* Command definition */
#define CONFIG_ETHPRIME "FEC0"
#define CONFIG_LOADADDR 0x72000000 /* loadaddr env var */
#define PPD_CONFIG_NFS \
"nfsserver=192.168.252.95\0" \
"gatewayip=192.168.252.95\0" \
"netmask=255.255.255.0\0" \
"ipaddr=192.168.252.99\0" \
"kernsize=0x2000\0" \
"use_dhcp=0\0" \
"nfsroot=/opt/springdale/rd\0" \
"bootargs_nfs=setenv bootargs ${bootargs} root=/dev/nfs " \
"${kern_ipconf} nfsroot=${nfsserver}:${nfsroot},v3,tcp rw\0" \
"choose_ip=if test $use_dhcp = 1; then setenv kern_ipconf ip=dhcp; " \
"setenv getcmd dhcp; else setenv kern_ipconf " \
"ip=${ipaddr}:${nfsserver}:${gatewayip}:${netmask}::eth0:off; " \
"setenv getcmd tftp; fi\0" \
"nfs=run choose_ip setargs bootargs_nfs; ${getcmd} ${loadaddr} " \
"${nfsserver}:${image}; bootm ${loadaddr}\0" \
#define CONFIG_EXTRA_ENV_SETTINGS \
PPD_CONFIG_NFS \
"image=/boot/fitImage\0" \
"fdt_high=0xffffffff\0" \
"dev=mmc\0" \
"devnum=2\0" \
"rootdev=mmcblk0p\0" \
"quiet=quiet loglevel=0\0" \
"console=" CONSOLE_DEV "\0" \
"lvds=ldb\0" \
"setargs=setenv bootargs ${lvds} jtag=on mem=2G " \
"vt.global_cursor_default=0 bootcause=${bootcause} ${quiet} " \
"console=${console}\0" \
"bootargs_emmc=setenv bootargs root=/dev/${rootdev}${partnum} ro " \
"rootwait ${bootargs}\0" \
"doquiet=if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; " \
"then setenv quiet; fi\0" \
"hasfirstboot=ext2load ${dev} ${devnum}:${partnum} 0x7000A000 " \
"/boot/bootcause/firstboot\0" \
"swappartitions=setexpr partnum 3 - ${partnum}\0" \
"failbootcmd=" \
"ppd_lcd_enable; " \
"msg=\"Monitor failed to start. " \
"Try again, or contact GE Service for support.\"; " \
"echo $msg; " \
"setenv stdout vga; " \
"echo \"\n\n\n\n \" $msg; " \
"setenv stdout serial; " \
"mw.b 0x7000A000 0xbc; " \
"mw.b 0x7000A001 0x00; " \
"ext4write ${dev} ${devnum}:5 0x7000A000 /boot/failures 2\0" \
"altbootcmd=" \
"run doquiet; " \
"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
"run hasfirstboot || setenv partnum 0; " \
"if test ${partnum} != 0; then " \
"setenv bootcause REVERT; " \
"run swappartitions loadimage doboot; " \
"fi; " \
"run failbootcmd\0" \
"loadimage=" \
"ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
"doboot=" \
"echo Booting from ${dev}:${devnum}:${partnum} ...; " \
"run setargs; " \
"run bootargs_emmc; " \
"bootm ${loadaddr}\0" \
"tryboot=" \
"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
"run loadimage || run swappartitions && run loadimage || " \
"setenv partnum 0 && echo MISSING IMAGE;" \
"run doboot; " \
"run failbootcmd\0" \
"video-mode=" \
"lcd:800x480-24@60,monitor=lcd\0" \
#define CONFIG_MMCBOOTCOMMAND \
"if mmc dev ${devnum}; then " \
"run doquiet; " \
"run tryboot; " \
"fi; " \
#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND
#define CONFIG_ARP_TIMEOUT 200UL
/* Miscellaneous configurable options */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_MAXARGS 48 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x70000000
#define CONFIG_SYS_MEMTEST_END 0x70010000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
/* Physical Memory Map */
#define PHYS_SDRAM_1 CSD0_BASE_ADDR
#define PHYS_SDRAM_1_SIZE (gd->bd->bi_dram[0].size)
#define PHYS_SDRAM_2 CSD1_BASE_ADDR
#define PHYS_SDRAM_2_SIZE (gd->bd->bi_dram[1].size)
#define PHYS_SDRAM_SIZE (gd->ram_size)
#define CONFIG_SYS_SDRAM_BASE (PHYS_SDRAM_1)
#define CONFIG_SYS_INIT_RAM_ADDR (IRAM_BASE_ADDR)
#define CONFIG_SYS_INIT_RAM_SIZE (IRAM_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* FLASH and environment organization */
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_CMD_FUSE
#define CONFIG_FSL_IIM
#define CONFIG_SYS_I2C_SPEED 100000
/* I2C1 */
#define CONFIG_SYS_NUM_I2C_BUSES 9
#define CONFIG_SYS_I2C_MAX_HOPS 1
#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
{0, {{I2C_MUX_PCA9547, 0x70, 0} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 6} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 7} } }, \
}
#define CONFIG_BCH
/* Backlight Control */
#define CONFIG_IMX6_PWM_PER_CLK 66666000
#endif /* __CONFIG_H */